Disposable graphite paper based sensor for sensitive simultaneous determination of hydroquinone and catechol

Cobalt-nickel phosphide supported on reduced graphene oxide for sensitive electrochemical detection of bisphenol A

Bisphenol A (BPA) is a commonly utilized phenolic contaminant in several manufacturing processes, contributing to environmental pollution. Therefore, the detection of BPA holds significant importance for monitoring water quality. In this work, we report a robust electrochemical detection method for BPA utilizing cobalt-nickel bimetal phosphide nanoparticles (CoNiP) supported on reduced graphene oxide (rGO). The CoNiP@rGO-modified glassy carbon electrode exhibits remarkable electrochemical activity in BPA detection. The detection mechanism is controlled by adsorption-mediated electron transfer, showcasing a low limit of detection (LOD) at 0.38 nM and a high sensitivity of 96.4 A M-1 cm-2 within the linear range of 0.001-8 μM. Furthermore, our developed sensor demonstrates good reproducibility and successfully detected BPA in actual water samples. The electrochemical activity of CoNiP@rGO was also characterized for hydroquinone (HQ) detected through a diffusion-controlled mechanism, displaying an excellent sensitivity of 36.4 A M-1 cm-2 across a broad linear range. These findings underscore the promising potential of CoNiP@rGO as a candidate for electrochemical detection of phenolic contaminants, especially in the sensing of BPA in environmental water samples. This efficacy is attributed to the modulation of its electronic properties, combined with its large electroactive surface area and low electron-transfer resistance.

CO2-plasma surface treatment of graphite sheet electrodes for detection of chloramphenicol, ciprofloxacin and sulphanilamide

Graphite sheet (GS) electrodes are flexible and versatile substrates for sensing electrochemical; however, their use has been limited to incorporate (bio)chemical modifiers. Herein, we demonstrated that a cold (low temperature) CO2 plasma treatment of GS electrodes provides a substantial improvement of the electrochemical activity of these electrodes due to the increased structural defects on the GS surface as revealed by Raman spectroscopy (ID/IG ratio), and scanning electron microscopy images. XPS analyses confirmed the formation of oxygenated functional groups at the GS surface after the plasma treatment that are intrinsically related to the substantial increase in the electron transfer coefficient (K0 values increased from 1.46 × 10-6 to 2.09 × 10-3 cm s-1) and with reduction of the resistance to charge transfer (from 129.8 to 0.251 kΩ). The improved electrochemical activity of CO2-GS electrodes was checked for the detection of emerging contaminant species, such as chloramphenicol (CHL), ciprofloxacin (CIP) and sulphanilamide (SUL) antibiotics, at around + 0.15, + 1.10 and + 0.85 V (versus Ag/AgCl), respectively, by square wave voltammetry. Limit of detection values in the submicromolar range were achieved for CHL (0.08 μmol L-1), CIP (0.01 μmol L-1) and SFL (0.11 μmol L-1), which enabled the sensor to be successfully applied to natural waters and urine samples (recovery values from 85 to 119%). The CO2-GS electrode is highly stable and inexpensive ($0.09 each sensor) and can be easily inserted in portable 3D printed cells for environmental on-site analyses.

Facile Synthesis of Copper-Coated-Reduced-Graphene-Oxide and Its Application as a Highly Sensitive Electrochemical Sensor for Hydroquinone

A facile step-by-step approach for synthesizing copper nanoparticles (CuNPs) loaded on the wrinkled surface of reduced-graphene-oxide (Cu/rGO) was conducted using a reductant at room temperature. Multiple characterization methods were applied to specify the morphology and composition of the nanocomposites. The scanning electron microscope and transmission electron microscope of Cu/rGO show that spherical CuNps were dispersed uniformly on the surface of rGO. In addition, the characteristic peaks of Cu and carbon in energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy analyses spectra proved that Cu/rGO nanocomposites were synthesized. Soon afterwards, a new hydroquinone electrochemical sensor was prepared with Cu/rGO and a glassy carbon electrode. The sensor was characterized by cyclic voltammetry and electrochemical impedance spectroscopy. Hydroquinone was detected by differential pulse voltammetry using the composite electrode. Under the optimal condition, the linear response range was from 0.05 μM to 90 μM; the detection limit is 0.02 μM (S/N = 3) for hydroquinone. The electrochemical sensor exhibited high sensitivity in practical environmental water sample detection.

Dihydroxybenzene isomers electrochemical sensor based on activated carbon sensitive material activated by mechanochemistry and low-dosage phosphoric acid

A dihydroxybenzene isomers electrochemical sensor based on bamboo activated carbon (MCPBAC) sensitive material activated by mechanochemistry and low-dosage phosphoric acid was fabricated in this work. The sensor, modified by MCPBAC with GCE, can significantly distinguish and sensitively measure hydroquinone (HQ) and catechol (CC). The MCPBAC exhibits a well-developed porous structure, high specific surface area, and good electrical conductivity. Using differential pulse voltammetry (DPV), wide linear ranges for both HQ and CC are 0.6-600 μM, with low detection limits (S/N = 3) for both of 0.2 μM. The dihydroxybenzene isomers electrochemical sensor has wide application prospects in the determination of trace HQ and CC in environmental water.

Coomassie brilliant blue G 250 modified carbon paste electrode sensor for the voltammetric detection of dihydroxybenzene isomers

In this present study, coomassie brilliant blue G-250 (CBBG) modified electrode was fabricated for the specific and simultaneous detection of three dihydroxybenzene isomers such as resorcinol (RS), catechol (CC) and hydroquinone (HQ). The fabrication of the modified electrode was carried out by electrochemical polymerization of CBBG on the surface of unmodified electrode. The surface structures of bare and fabricated electrode were studied by scanning electron microscope (SEM). The established electrode portrays the very fine interface with these isomers and displayed the sufficient sensitivity and selectivity. The specific parameters of pH solution, scan rate and varying the concentration of analytes were optimized at the modified electrode. The sensor process was originated to be adsorption-controlled activity and the low limit of detection (LOD) for RS and CC was attained at 0.24 and 0.21 µM respectively. In the simultaneous study, designed sensor clearly implies the three well separated anodic peaks for RS, HQ and CC nevertheless in unmodified electrode it failed. Also, the constructed electrode was applied for the real sample analysis in tap water and obtained results are agreeable and it consistent in-between 92.80–99.48%.

An efficient electrochemical sensing of hazardous catechol and hydroquinone at direct green 6 decorated carbon paste electrode

In this proposed work, direct green 6 (DG6) decorated carbon paste electrode (CPE) was fabricated for the efficient simultaneous and individual sensing of catechol (CA) and hydroquinone (HY). Electrochemical deeds of the CA and HY were carried out by cyclic voltammetry (CV) and differential pulse voltammetry (DPV) at poly-DG6-modfied carbon paste electrode (Po-DG6-MCPE). Using scanning electron microscopy (SEM) studied the surface property of unmodified CPE (UCPE) and Po-DG6-MCPE. The decorated sensor displayed admirable electrocatalytic performance with fine stability, reproducibility, selectivity, low limit of detection (LLOD) for HY (0.11 μM) and CC (0.09 μM) and sensor process was originated to be adsorption-controlled phenomena. The Po-DG6-MCPE sensor exhibits well separated two peaks for HY and CA in CV and DPV analysis with potential difference of 0.098 V. Subsequently, the sensor was practically applied for the analysis in tap water and it consistent in-between for CA 93.25–100.16% and for HY 97.25–99.87% respectively.

Gold-Carbon Nanocomposites for Environmental Contaminant Sensing

The environmental crisis, due to the rapid growth of the world population and globalisation, is a serious concern of this century. Nanoscience and nanotechnology play an important role in addressing a wide range of environmental issues with innovative and successful solutions. Identification and control of emerging chemical contaminants have received substantial interest in recent years. As a result, there is a need for reliable and rapid analytical tools capable of performing sample analysis with high sensitivity, broad selectivity, desired stability, and minimal sample handling for the detection, degradation, and removal of hazardous contaminants. In this review, various gold–carbon nanocomposites-based sensors/biosensors that have been developed thus far are explored. The electrochemical platforms, synthesis, diverse applications, and effective monitoring of environmental pollutants are investigated comparatively.

A study on the electrochemical behavior of hydroquinone at a nanometer cobalt/l-glutamate-modified electrode

A new electrochemical sensor for hydroquinone (HQ) was prepared. The electrochemical sensor was modified by electrodeposition and electrochemical polymerization to modify nanometer cobalt (nano-Co) and poly-l-glutamic acid (poly-l-glu) on the surface of a glassy carbon electrode (GCE). Then, the electrochemical behavior of hydroquinone on the electrochemical sensor was investigated by cyclic voltammetry (CV). The experimental conditions were optimized from the aspects of electrolyte type, concentration, acidity, enrichment time and scanning speed. The experimental results showed that under optimized conditions the oxidation peak current has a good linear relationship with the concentration of hydroquinone in the range of 3.85 × 10⁻⁶ to 1.30 × 10⁻³ mol L⁻¹ (R² = 0.9998). Moreover, there was a low detection limit of 4.97 × 10⁻⁷ mol L⁻¹. When the sensor was used for the analysis of hydroquinone in water samples, the recoveries with satisfactory results were in the range of 97.2–102.6%.

A new electrochemical sensor for hydroquinone (HQ) was prepared.

Simultaneous sensitive determination of benzenediol isomers using multiwall carbon nanotube–ionic liquid modified carbon paste electrode by a combination of artificial neural network and fast Fourier transform admittance voltammetry

A novel electrochemical method for the simultaneous determination of catechol, hydroquinone, and resorcinol.

A sensitive and disposable indium tin oxide based electrochemical immunosensor for label-free detection of MAGE-1

MAGE-1 (MAGE, for melanoma antigen), was identified by virtue of its processing and cell surface expression as a tumor-specific peptide bound to major histocompatibility complexes which was reactive with autolytic T cells. 3-Glycidoxypropyltrimethoxysilane (3-GOPS) is frequently employed for the preparation of dense heterometal hybrid polymers which are used, e.g., for hard coatings of organic polymers and contact lens materials in the optical industry. In this study, we have improved a new immunological biosensor with indium tin oxide (ITO). Then, Anti-MAGE-1 antibody was covalently immobilized with 3-GOPS which formed a self-assembled monolayers (SAMs) on modified ITO electrodes. Analytical characteristics such as square wave voltammetry, linear determination range, repeatability, reproducibility and regeneration of biosensors are determined. All characterization steps are monitored by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV). The developed biosensor has wide determination range (0.5fg-15fg/mL). To investigate long shelf life of the fabricated biosensor, the immunosensors were stored at 4°C for periods ten weeks. Futhermore, binding kinetics of MAGE1 to antiMAGE-1 is monitored by single frequency technique in real time. Additionally, Kramer's-Kronig transform was used to understand whether the impedance spectra of biosensor system are affected from the variation that occurred because of external factor. Morphological characteristics of constructed biosensor were observed by scanning electron microscopy. Real human serum samples were also analyzed by the proposed biosensor, successfully. A commercial ELISA kit was also used as a reference method to validate the results obtained by the biosensor. Finally, this biosensor was tried in real blood sample and that showed it could be utilized in clinical applications. This biosensor can be preferred due to it has a wide linear range and it can be prepared easily.