Synthesis and characterization of MnO 2 -decorated graphene for supercapacitors

Unveiling the potential of PANI@MnO2@rGO ternary nanocomposite in energy storage and gas sensing

The development of advanced materials for energy storage and gas sensing applications has gained significant attention in recent years. In this study, we synthesized and characterized PANI@MnO2@rGO ternary nanocomposites (NCs) to explore their potential in supercapacitors and gas sensing devices. The ternary NCs were synthesized through a multi-step process involving the hydrothermal synthesis of MnO2 nanoparticles, preparation of PANI@rGO composites and the assembly to the ternary PANI@MnO2@rGO ternary NCs. The structural, morphological, and compositional characteristics of the materials were thoroughly analyzed using techniques such as XRD, FESEM, TEM, FTIR, and Raman spectroscopy. In the realm of gas sensing, the ternary NCs exhibited excellent performance as NH3 gas sensors. The optimized operating temperature of 100 °C yielded a peak response of 15.56 towards 50 ppm NH3. The nanocomposites demonstrated fast response and recovery times of 6 s and 10 s, respectively, and displayed remarkable selectivity for NH3 gas over other tested gases. For supercapacitor applications, the electrochemical performance of the ternary NCs was evaluated using cyclic voltammetry and galvanostatic charge-discharge techniques. The composites exhibited pseudocapacitive behavior, with the capacitance reaching up to 185 F/g at 1 A/g and excellent capacitance retention of approximately 88.54% over 4000 charge-discharge cycles. The unique combination of rGO, PANI, and MnO2 nanoparticles in these ternary NCs offer synergistic advantages, showcasing their potential to address challenges in energy storage and gas sensing technologies.

Removal of methylene blue using MnO2@rGO nanocomposite from textile wastewater: Isotherms, kinetics and thermodynamics studies

In this study, the adsorptive removal of methylene blue dye, which is commonly used in textile industries, was investigated using the MnO₂@reduced graphene oxide (rGO) adsorbent. The sonication-assisted synthesis from rGO nanosheets and MnO₂ nanoparticles resulted to the MnO₂@rGO nanocomposite with improved physicochemical properties. The characterization results showed the improved surface area, porous structure and adsorption sites from the nitrogen adsorption-desorption studies, improved morphology from the Scanning Electron Microscope (SEM) and Transmission Electron Microscope (TEM) and the improved crystal structure from X-ray powder diffraction (XRD). The improved physicochemical properties on the MnO₂@rGO nanocomposite played a significant role in enhancing the dye removal in textile wastewater. The equilibrium experimental data was best described by the Langmuir isotherm model with a maximum adsorption capacity of 156 mg g^-1, suggesting a monolayer adsorption. The kinetic data best fitted the pseudo-second order kinetic model, suggesting a chemisorption adsorption process. The thermodynamic data (ΔG°, ΔH° and ΔS°) confirmed the feasibility, randomness and spontaneous nature of the adsorption process. The mechanism of adsorption involved the hydrogen bonding, π-π interactions and electrostatic interactions. The removal of methylene blue using MnO₂@rGO nanocomposite in spiked textile wastewater yielded a 98-99% removal. The method demonstrated competitiveness when compared with literature reported results, paving way for further investigations towards industrial scale applications.

Catalytic oxidation of VOCs over 3D@2D Pd/CoMn2O4 nanosheets supported on hollow Al2O3 microspheres

Catalytic oxidation is a promising method for removing harmful volatile organic compounds (VOCs). Therefore, exploring high-efficiency catalysts for catalyzing VOCs is of great significance to the realization of an environment-friendly and sustainable society. Here, a series of 3D@2D constructed Al₂O₃@CoMn₂O₄ microspheres with a hollow hierarchical structure supporting Pd nanoparticles was successfully synthesized. The introduction of hollow Al₂O₃ for the in situ vertical growth of 2D CMO spinel materials constructs a well-defined core - shell hollow hierarchical structure, leading to larger specific surface area, more accessible active sites and promoted catalytic activity of support material. Additionally, theoretical calculations also indicate that the addition of Al₂O₃ as the support material strengthens the adsorption of toluene and oxygen on CoMn₂O₄, which promotes their activation. The dispersion of Pd further strengthens the low-temperature reducibility along with more active surface oxygen species and lower apparent activation energy. The optimum 1 wt% Pd/h-Al@4CMO catalyst possesses the lowest apparent activation energy for toluene of 77.4 kJ mol^-1, showing the relatively best catalytic activity for VOC oxidation, reaching 100% toluene, benzene, and ethyl acetate conversion at 165, 160, and 155 °C, respectively. Meanwhile, the 1 wt% Pd/h-Al@4CMO sample possesses excellent catalytic stability, outstanding selectivity, and good moisture tolerance, which is an effective candidate for eliminating VOCs contaminants.

Flash-Induced Ultrafast Production of Graphene/MnO with Extraordinary Supercapacitance

Production of high-capacitance electrodes beyond the theoretical limit of 550 F g^-1 of pure graphene materials is highly desired for energy storage applications, yet remains an open challenge, especially with a facile and simple process. By rational design of reaction condition guided by theoretical analysis, the ultrafast (within millisecond) fabrication of high-performance graphene/MnO electrodes via a low-cost and one-step flash reduction process is proposed and demonstrated. This simple method enables high-quality porous graphene networks and the effective synthesis of embedding pseudocapacitive-active MnO nanomaterials simultaneously. Due to the high-density and homogeneous distribution of MnO nano-needles on 3D graphene networks, an ultrahigh capacitance (up to 1706 F g^-1 based on electrode mass and 2150 F g^-1 based on MnO mass only) is demonstrated. Functional supercapacitor prototype further illustrates the broad potential applications enabled by the fabricated electrodes in energy storage, sensing, and catalysts.

Ternary flower-sphere-like MnO2-graphite/reduced graphene oxide nanocomposites for supercapacitor

Chemical fabrication of a nanocomposite structure for electrode materials to regulate the ion diffusion channels and charge transfer resistances and Faradaic active sites is a versatile strategy towards building a high-performance supercapacitor. Here, a new ternary flower-sphere-like nanocomposite MnO₂-graphite (MG)/reduced graphene oxide (RGO) was designed using the RGO as a coating for the MG. MnO₂-graphite (MnO₂-4) was obtained by KMnO₄ oxidizing the pretreated graphite in an acidic medium (pH = 4). The GO coating was finally reduced by the NaBH₄ to prepare the ternary nanocomposite MG. The microstructures and pore sizes were investigated by x-ray diffraction, scanning electron microscopy, thermogravimetric analysis, and nitrogen adsorption/desorption. The electrochemical properties of MG were systematically investigated by the cyclic voltammetry, galvanostatic charge-discharge, and electrochemical impedance spectroscopy in Na₂SO₄ solution. The MG as an electrode material for supercapacitor exhibits a specific capacitance of 478.2 and 454.6 F g^-1 at a current density of 1.0 and 10.0 A g^-1, respectively. In addition, the capacitance retention was 90% after 8,000 cycles. The ternary nanocomposite enhanced electrochemical performance originates from the specific flower-sphere-like morphology and coating architecture bringing higher specific surface area and lower charge transfer resistance (R_ct).

Hybridized Graphene for Supercapacitors: Beyond the Limitation of Pure Graphene

Graphene-based supercapacitors have been attracting growing attention due to the predicted intrinsic high surface area, high electron mobility, and many other excellent properties of pristine graphene. However, experimentally, the state-of-the-art graphene electrodes face limitations such as low surface area, low electrical conductivity, and low capacitance, which greatly limit their electrochemical performances for supercapacitor applications. To tackle these issues, hybridizing graphene with other species (e.g., atom, cluster, nanostructure, etc.) to enlarge the surface area, enhance the electrical conductivity, and improve capacitance behaviors are strongly desired. In this review, different hybridization principles (spacers hybridization, conductors hybridization, heteroatoms doping, and pseudocapacitance hybridization) are discussed to provide fundamental guidance for hybridization approaches to solve these challenges. Recent progress in hybridized graphene for supercapacitors guided by the above principles are thereafter summarized, pushing the performance of hybridized graphene electrodes beyond the limitation of pure graphene materials. In addition, the current challenges of energy storage using hybridized graphene and their future directions are discussed.

Melt-spun modified poly (styrene-co-butyl acrylate) fiber as a carrier to support manganese oxide and its application in dye wastewater decolorization

Polymer fiber, a kind of versatile material, has been widely used in many fields. However, emerging applications still urge us to develop some new kinds of fibers. Advanced oxidation processes (AOPs) have created a promising prospect for organic wastewater decontamination; thus, it is of important significance to design a kind of special fiber that can be applied in AOPs. In this work, a viable route is proposed to fabricate manganese oxide-supporting melt-spun modified poly (styrene-co-butyl acrylate) fiber, and the prepared fiber has an excellent activity to catalyze H₂O₂ and O₃ to decolorize dye-containing water. The results show that the decolorization of a cationic blue solution can be completely accomplished within 10 min with the prepared fiber as a catalyst, and its decolorization efficiency can reach up to 96.2% within 40 min. The concentration of total organic carbon can decrease from 20.3 to 12.3 mg/L. The prepared fiber can be reused five times without any loss in decolorization efficiency. Compared with other manganese oxide-based catalysts reported in the literature, the prepared fiber also shows many advantages in decolorizing methylene blue such as easy separation, mild reaction condition, and high decolorization efficiency. Therefore, we are confident that the fiber introduced in this study will exhibit a great application potential in the field of dye wastewater treatment.

Polyacrylonitrile homogeneous blend hollow fiber membrane with stable structure as a substrate to support Fe/Mn oxide and its enhanced capability to purify dye wastewater

Blending different molecular weight polyacrylonitrile (PAN) was adopted to solve the shrinkage problem of high molecular weight PAN hollow fiber membrane, to enhance the application performance of low molecular weight PAN membrane, and to adjust the porosity, pore size distribution, and hydrophilicity of the end product. The structurally-optimized membrane was chosen as a substrate to support Fe/Mn oxides and then used as a reactor to remove dyes from their solutions in the presence of H2O2. The results showed that the flux of methylene blue (MB) aqueous solution was 83.7 L/m2 h for the PAN homogeneous blend membrane, much higher than 29.1 L/m2 h of high molecular weight PAN membrane; MB removal efficiency was 97.3%, higher than 62.3% of low molecular weight PAN membrane, and it could be reused 25 times to remove dyes from their solutions without any loss in removal efficiency. The membrane was also found to have the application advantages of decreasing H2O2 dosage, reducing operation pressure, and raising MB removal efficiency compared with other membranes reported in the pieces of literature. Therefore, we were confident that the hollow fiber membrane fabricated by us would exhibit great application potential in the field of decontaminating dye wastewater.

Hydrothermal Synthesis of Cobalt Ruthenium Sulfides as Promising Pseudocapacitor Electrode Materials

In this paper, we report the successful synthesis of cobalt ruthenium sulfides by a facile hydrothermal method. The structural aspects of the as-prepared cobalt ruthenium sulfides were characterized using X-ray diffraction, X-ray photoelectron spectroscopy, and Raman spectroscopy. All the prepared materials exhibited nanocrystal morphology. The electrochemical performance of the ternary metal sulfides was investigated by cyclic voltammetry (CV), galvanostatic charge-discharge (GCD), and electrochemical impedance spectroscopy techniques. Noticeably, the optimized ternary metal sulfide electrode exhibited good specific capacitances of 95 F g−1 at 5 mV s−1 and 75 F g−1 at 1 A g−1, excellent rate capability (48 F g−1 at 5 A g−1), and superior cycling stability (81% capacitance retention after 1000 cycles). Moreover, this electrode demonstrated energy densities of 10.5 and 6.7 Wh kg−1 at power densities of 600 and 3001.5 W kg−1, respectively. These attractive properties endow proposed electrodes with significant potential for high-performance energy storage devices.

Effect of nickel ion doping in MnO2/reduced graphene oxide nanocomposites for lithium adsorption and recovery from aqueous media

Novel and effective reduced graphene oxide–nickel (Ni) doped manganese oxide (RGO/Ni-MnO₂) adsorbents were fabricated via a hydrothermal approach. The reduction of graphite to graphene oxide (GO), formation of α-MnO₂, and decoration of Ni-MnO₂ onto the surface of reduced graphene oxide (RGO) were independently carried out by a hydrothermal technique. The physical and morphological properties of the as-synthesized adsorbents were analyzed. Batch adsorption experiments were performed to identify the lithium uptake capacities of adsorbents. The optimized parameters for Li⁺ adsorption investigated were pH = 12, dose loading = 0.1 g, Li⁺ initial concentration = 50 mg L⁻¹, in 10 h at 25 °C. It is noticeable that the highest adsorption of Li⁺ at optimized parameters are in the following order: RGO/Ni3-MnO₂ (63 mg g⁻¹) > RGO/Ni2-MnO₂ (56 mg g⁻¹) > RGO/Ni1-MnO₂ (52 mg g⁻¹). A Kinetic study revealed that the experimental data were best designated pseudo-second order for each adsorbent. Li⁺ desorption experiments were performed using HCl as an extracting agent. Furthermore, all adsorbents exhibit efficient regeneration ability and to some extent satisfying selectivity for Li⁺ recovery. Briefly, it can be concluded that among the fabricated adsorbents, the RGO/Ni3-MnO₂ exhibited the greatest potential for Li⁺ uptake from aqueous solutions as compared to others.

Novel and effective reduced graphene oxide–nickel (Ni) doped manganese oxide (RGO/Ni-MnO₂) adsorbents were fabricated via a hydrothermal approach for lithium adsorption and recovery from aqueous media.

An efficient electrode material for high performance solid-state hybrid supercapacitors based on a Cu/CuO/porous carbon nanofiber/TiO2 hybrid composite

A Cu/CuO/porous carbon nanofiber/TiO2 (Cu/CuO/PCNF/TiO2) composite uniformly covered with TiO2 nanoparticles was synthesized by electrospinning and a simple hydrothermal technique. The synthesized composite exhibits a unique morphology and excellent supercapacitive performance, including both electric double layer and pseudo-capacitance behavior. Electrochemical measurements were performed by cyclic voltammetry, galvanostatic charge-discharge and electrochemical impedance spectroscopy. The highest specific capacitance value of 530 F g-1 at a current density of 1.5 A g-1 was obtained for the Cu/CuO/PCNF/TiO2 composite electrode in a three-electrode configuration. The solid-state hybrid supercapacitor (SSHSC) fabricated based on this composite exhibits a high specific capacitance value of 330 F g-1 at a current density of 1 A g-1 with 78.8% capacitance retention for up to 10,000 cycles. At the same time, a high energy density of 45.83 Wh kg-1 at a power density of 1.27 kW kg-1 was also realized. The developed electrode material provides new insight into ways to enhance the electrochemical properties of solid-state supercapacitors, based on the synergistic effect of porous carbon nanofibers, metal and metal oxide nanoparticles, which together open up new opportunities for energy storage and conversion applications.

Asymmetric pseudo-capacitors based on dendrite-like MnO2 nanostructures

Dendrite-like MnO₂ nanostructures grown on carbon cloth are successfully prepared by a facile one-step route.

Research Progress in MnO2 -Carbon Based Supercapacitor Electrode Materials

With the serious impact of fossil fuels on the environment and the rapid development of the global economy, the development of clean and usable energy storage devices has become one of the most important themes of sustainable development in the world today. Supercapacitors are a new type of green energy storage device, with high power density, long cycle life, wide temperature range, and both economic and environmental advantages. In many industries, they have enormous application prospects. Electrode materials are an important factor affecting the performance of supercapacitors. MnO₂ -based materials are widely investigated for supercapacitors because of their high theoretical capacitance, good chemical stability, low cost, and environmental friendliness. To achieve high specific capacitance and high rate capability, the current best solution is to use MnO₂ and carbon composite materials. Herein, MnO₂ -carbon composite as supercapacitor electrode materials is reviewed including the synthesis method and research status in recent years. Finally, the challenges and future development directions of an MnO₂ -carbon based supercapacitor are summarized.