Pyramid-like CdS nanoparticles grown on porous TiO 2 monolith: An advanced photocatalyst for H 2 production

Enhancing mechanical and photocatalytic properties by surface microstructure regulation of TiO2 nanofiber membranes

In this work, TiO₂ nanofiber membrane (NFM) with a complete surface microstructure was prepared through regulating the surface microstructure of TiO₂ NFM by doping Zr. The crystal structures and morphological analyses indicated that the nanofiber membranes were consisted by disordered accumulation of Zr-doped TiO₂ nanofibers with a crack-free surface, small grain size and high aspect ratio. When the doping amount of Zr was 0.8 mL, the tensile strength of the doped membranes reached 1.27 MPa, which was 60.7% higher than that of pure TiO₂ NFM. The photocatalytic performance of Zr-doped TiO₂ NFM was evaluated by the degradation performance of Methylene orange (MO) under simulated sunlight irradiation. Compared with the undoped TiO₂ NFM, the 0.8-Zr/TiO₂ NFM presented a higher catalytic degradation efficiency (improved by 69.6%), and the photocatalytic performance maintained stable after five circulating. It was found that the doping of Zr ions effectively limited the surface crack size and grain size of TiO₂ nanofibers, thereby improving the tensile strength, and enhanced the surface area effect and carrier transfer efficiency of TiO₂ NFM. On the other hand, a narrow band-gap was obtained by doping a small amount of Zr ions, which expanded the visible light response range to improve the photocatalytic performance of TiO₂ nanofibers.

Enhanced photocatalytic degradation of Acid Blue dye using CdS/TiO2 nanocomposite

Photocatalytic degradation is essential for the successful removal of organic contaminants from wastewater, which is important for ecological and environmental safety. The advanced oxidation process of photocatalysis has become a hot topic in recent years for the remediation of water. Cadmium sulphide (CdS) nanostructures doped with Titanium oxide (CdS/TiO₂) nanocomposites has manufactured under ambient conditions using a simple and modified Chemical Precipitation technique. The nanocomposites crystal structure, thermal stability, recombination of photo-generated charge carriers, bandgap, surface morphology, particle size, molar ratio, and charge transfer properties are determined. The production of nanocomposites (CdS-TiO₂) and their efficient photocatalytic capabilities are observed. The goal of the experiment is to improve the photocatalytic efficiency of TiO₂ in the visible region by doping CdS nanocomposites. The results showed that as-prepared CdS-TiO₂ nanocomposites has exhibited the highest photocatalytic activity in the process of photocatalytic degradation of AB-29 dye, and its degradation efficiency is 84%. After 1 h 30 min of visible light irradiation, while CdS and TiO₂ showed only 68% and 09%, respectively. The observed decolorization rate of AB-29 is also higher in the case of CdS-TiO₂ photocatalyst ~ 5.8 × 10⁻⁴mol L⁻¹ min⁻¹) as compared to the reported decolorization rate of CdS ~ 4.5 × 10⁻⁴mol L⁻¹ min⁻¹ and TiO₂ ~ 0.67 × 10⁻⁴mol L⁻¹ min⁻¹. This increased photocatalytic effectiveness of CdS-TiO₂ has been accomplished by reduced charge carrier recombination as a result of improved charge separation and extension of TiO₂ in response to visible light.

Facile decoration of CdS nanoparticles on TiO2: robust photocatalytic activity under LED illumination

A facile approach is presented to obtain visible-light-active TiO2/CdS nanocomposites with visible-light photocatalytic activity. Ordered nanospheres of TiO2 (with anatase as the main crystalline phase) were synthesized using evaporation-induced self-assembly (EIS) with P123 block polymer without any hazardous additives. Then, a rapid microwave (MW) protocol was used to obtain visible-light-absorbing nanocomposites between TiO2 and CdS in just 10 s. Based on Rietveld refinements of X-ray diffractrograms and elemental analysis it was found that nanoparticles of CdS are mainly decorated between the nanospheres of TiO2, which can simultaneously improve light absorption and suppress the unwanted photo-corrosion effects. The prepared nanocomposites were put to test for the removal of malachite green as a model pollutant from aqueous media under irradiation. The results revealed, that excessive loading results in unwanted surface covering and less than ideal activity, but for the sample with optimized loading, about 86 and 77% of the pollutant was degraded after 100 min of illumination at room temperature under the xenon short-arc and LED illumination, respectively.

Controllable growth of three-dimensional CdS nanoparticles on TiO2 nanotubes to enhance photocatalytic activity

Exploiting photocatalysts with characteristics of low cost, high reactivity and good recyclability is a great significance for environmental remediation and energy conversion. Herein, hollow TiO2 nanotubes were fabricated by a novel and efficient method via electrospinning and an impregnation calcination method. With the hydrothermal method, the CdS nanoparticles were modified on the surface and in walls of the TiO2 nanotubes. By changing the reaction conditions, the morphology of CdS nanoparticles presents a controllable three-dimensional (3D) structure. The morphology of the samples was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The structure and components of samples were characterized by X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX) and X-ray photoelectron spectroscopy (XPS). The light absorption efficiency was detected using UV-vis diffuse reflectance spectroscopy (DRS) and photoluminescence (PL). The photocatalytic properties were evaluated by degradation of methyl orange (MO) and photocatalytic hydrogen evolution under visible light irradiation. From the results, the TiO2/CdS nanotubes exhibit better photocatalytic activity than the pure TiO2. The synthetic mechanism of TiO2/CdS heterostructures and a possible photocatalytic mechanism based on the experimental results were proposed.

Recent Achievements in Development of TiO2-Based Composite Photocatalytic Materials for Solar Driven Water Purification and Water Splitting

Clean water and the increased use of renewable energy are considered to be two of the main goals in the effort to achieve a sustainable living environment. The fulfillment of these goals may include the use of solar-driven photocatalytic processes that are found to be quite effective in water purification, as well as hydrogen generation. H2 production by water splitting and photocatalytic degradation of organic pollutants in water both rely on the formation of electron/hole (e-/h+) pairs at a semiconducting material upon its excitation by light with sufficient photon energy. Most of the photocatalytic studies involve the use of TiO2 and well-suited model compounds, either as sacrificial agents or pollutants. However, the wider application of this technology requires the harvesting of a broader spectrum of solar irradiation and the suppression of the recombination of photogenerated charge carriers. These limitations can be overcome by the use of different strategies, among which the focus is put on the creation of heterojunctions with another narrow bandgap semiconductor, which can provide high response in the visible light region. In this review paper, we report the most recent advances in the application of TiO2 based heterojunction (semiconductor-semiconductor) composites for photocatalytic water treatment and water splitting. This review article is subdivided into two major parts, namely Photocatalytic water treatment and Photocatalytic water splitting, to give a thorough examination of all achieved progress. The first part provides an overview on photocatalytic degradation mechanism principles, followed by the most recent applications for photocatalytic degradation and mineralization of contaminants of emerging concern (CEC), such as pharmaceuticals and pesticides with a critical insight into removal mechanism, while the second part focuses on fabrication of TiO2-based heterojunctions with carbon-based materials, transition metal oxides, transition metal chalcogenides, and multiple composites that were made of three or more semiconductor materials for photocatalytic water splitting.

Gradient Energy Band Driven High-Performance Self-Powered Perovskite/CdS Photodetector

Self-powered photodetectors are highly desired to meet the great demand in applications of sensing, communication, and imaging. Manipulating the carrier separation and recombination is critical to achieve high performance. In this paper, a self-powered photodetector based on the integrated gradient O-doped CdS nanorod array and perovskite is presented. Through optimizing the degree of continuous built-in band bending in the gradient-O CdS, the photodetector demonstrates a remarkable detectivity of 2.1 × 10¹³ Jones. Under the self-powered voltage mode, the responsivity can be as high as 0.48 A W^-1 , and the rise and decay time are 0.54/2.21 ms. The comprehensive performance is comparable and even better than reported perovskite and other types of self-powered photodetectors. The improved mechanism reveals that the gradient band bending promotes the photogenerated carrier transfer and hinders the recombination at the interface.