A comparative study of LiTi2(P8/9V1/9O4)3 and LiTi2(PO4)3: Synthesis, structure and electrochemical properties

Latest progress and challenges associated with lithium-ion semi-solid flow batteries: a critical review

Since the proposal of the concept of semi-solid flow batteries (SSFBs), SSFBs have gained increased attention as an alternative for large-scale energy storage applications. As a new type of high energy density flow battery system, lithium-ion semi-solid flow batteries (Li-SSFBs) combine the features of both flow batteries and lithium-ion batteries and show the advantages of decoupling power and capacity. Moreover, Li-SSFBs typically can achieve much higher energy density while maintaining a lower cost. Therefore, Li-SSFBs are some of the most promising technologies for future energy storage. Despite these advantages, a significant gap towards the commercialization of Li-SSFBs still exists. In this article, we have reviewed the research progress of Li-SSFBs in aqueous and non-aqueous systems in recent years. We have further discussed the future research trends and application prospects of Li-SSFBs, providing guidelines for future research in this area.

Two-dimensional LiTi2(PO4)3 flakes for enhanced lithium ions battery anode

In this work, the LiTi2(PO4)3 (LTP) flakes have been prepared by employing a template method for lithium-ion batteries with high capacity. The 2D layered structure of LTP offers large aspect ratio and rich active sites, which not only create the large contact area between the electrolyte and electrode, but also promote the diffusion kinetics of Li+. As a result, the Li+ diffusion coefficient of lamellar LTP anode is 3.12 × 10-8 cm2 s-1, while it is only 5.01 × 10-10 cm2 s-1 for granular LTP anode. Further, the lamellar LTP anode delivers a high initial discharge capacity of 986.8 mAh·g-1 at 0.1 A g-1, and remains at 231.1 mAh·g-1 after 100 cycles, which is higher than that of the granular LTP anode (340.5 mAh·g-1 at 1st cycle, 169.3 mAh·g-1 at 100th cycles). Thus, the lamellar LTP should be recommended as a potential anode for high-performance LIBs due to the fast charge-discharge performance and superior cycling stability.

Synthesis and electrochemical properties of Mn-doped Li2Mn0.1Ti1.9(PO4)3 materials

The hunt for a higher power storage, relatively inexpensive, non-polluting battery technology is currently a pressing issue because of the rapid growth of the worldwide economic and the progressively significant environmental pollution. Among the possible nanomaterials for rechargeable batteries that can have heteroatoms applied to it in order to improve its electrochemical behavior is Li_xTi_y(PO₄)₃. Carbon-coated Mn-doped Li₂Mn_0.1Ti_1.9(PO₄)₃ materials was synthesized by spray drying method. The material was characterized by XRD, SEM, TEM, BET, TGA et al. Crystal data refinement results by Rietveld method showed that the symmetry space group is Pbcn.The lattice parameters of Li₂Mn_0.1Ti_1.9(PO₄)₃ are a = 11.9372 Å, b = 8.5409 Å, c = 8.5979 Å, α = β = γ = 90°, V = 876.59 ų and Z = 4). Rietveld refinement was performed, and the confidence factors are Rwp = 11.79%, Rp = 9.14%, and χ² = 1.425. It was exhibited that LMTP0.1/CA-700 material has good crystallinity. Testing the cells with LAND test procedure (200 mA/g current density for 200 cycles), the LMTP0.1/CA-700 material has a discharge specific capacity of about 65 mAh/g. The capacity decayed by only 3% during the cycle. It has some potential application values as cathode of lithium ion battery in the future.