Influence of annealing atmosphere on Li2ZrO3-coated LiNi0.6Co0.2Mn0.2O2 and its high-voltage cycling performance

Enhanced Structural Stability and Electrochemical Performance of LiNi0.6Co0.2Mn0.2O2 Cathode Materials by Ga Doping

Structural instability during cycling is an important factor affecting the electrochemical performance of nickel-rich ternary cathode materials for Li-ion batteries. In this work, enhanced structural stability and electrochemical performance of LiNi_0.6Co_0.2Mn_0.2O₂ cathode materials are achieved by Ga doping. Compared with the pristine electrode, Li[Ni_0.6Co_0.2Mn_0.2]_0.98Ga_0.02O₂ electrode exhibits remarkably improved electrochemical performance and thermal safety. At 0.5C rate, the discharge capacity increases from 169.3 mAh g^-1 to 177 mAh g^-1, and the capacity retention also rises from 82.8% to 89.8% after 50 cycles. In the charged state of 4.3 V, its exothermic temperature increases from 245.13 °C to more than 271.24 °C, and the total exothermic heat decreases from 561.7 to 225.6 J·g^-1. Both AC impedance spectroscopy and in situ XRD analysis confirmed that Ga doping can improve the stability of the electrode/electrolyte interface structure and bulk structure during cycling, which helps to improve the electrochemical performance of LiNi_0.6Co_0.2Mn_0.2O₂ cathode material.

Preparation and Electrochemical Properties of LiNi2/3Co1/6Mn1/6O2 Cathode Material for Lithium-Ion Batteries

The cathode material LiNi_2/3Co_1/6Mn_1/6O₂ with excellent electrochemical performance was prepared successfully by a rheological phase method. The materials obtained were characterized by X-ray diffraction, scanning electron microscopy, electrochemical impedance spectroscopy and charge-discharge tests. The results showed that both calcination temperatures and atmosphere are very important factors affecting the structure and electrochemical performance of LiNi_2/3Co_1/6Mn_1/6O₂ material. The sample calcinated at 800 °C under O₂ atmosphere displayed well-crystallized particle morphology, a highly ordered layered structure with low defects, and excellent electrochemical performance. In the voltage range of 2.8–4.3 V, it delivered capacity of 188.9 mAh g⁻¹ at 0.2 C and 130.4 mAh g⁻¹ at 5 C, respectively. The capacity retention also reached 93.9% after 50 cycles at 0.5 C. All the results suggest that LiNi_2/3Co_1/6Mn_1/6O₂ is a promising cathode material for lithium-ion batteries.

Li2ZrO3-Coated NCM622 for Application in Inorganic Solid-State Batteries: Role of Surface Carbonates in the Cycling Performance

All-inorganic solid-state batteries (SSBs) currently attract much attention as next-generation high-density energy-storage technology. However, to make SSBs competitive with conventional Li-ion batteries, several obstacles and challenges must be overcome, many of which are related to interface stability issues. Protective coatings can be applied to the electrode materials to mitigate side reactions with the solid electrolyte, with lithium transition metal oxides, such as LiNbO₃ or Li₂ZrO₃, being well established in research. In addition, it has been recognized lately that carbonates incorporated into the coating may also positively affect the interface stability. In this work, we studied the effect that surface carbonates in case of Li₂ZrO₃-coated Li_1+x(Ni_0.6Co_0.2Mn_0.2)_1-xO₂ (NCM622) cathode material have on the cyclability of pellet stack SSB cells with Li₆PS₅Cl and Li₄Ti₅O₁₂ as a solid electrolyte and an anode, respectively. Both carbonate-rich and carbonate-poor hybrid coatings were produced by altering the synthesis conditions. The best cycling performance was achieved for carbonate-deficient Li₂ZrO₃-coated NCM622 due to decreased degradation of the argyrodite solid electrolyte at the interfaces, as determined by ex situ X-ray photoelectron spectroscopy and in situ differential electrochemical mass spectrometry. The results emphasize the importance of tailoring the composition and nature of protective coatings to improve the cyclability of bulk SSBs.

Simultaneous Enhancement of Interfacial Stability and Kinetics of Single-Crystal LiNi0.6Mn0.2Co0.2O2 through Optimized Surface Coating and Doping

Balancing interfacial stability and Li⁺ transfer kinetics through surface engineering is a key challenge in developing high-performance battery materials. Although conformal coating enabled by atomic layer deposition (ALD) has shown great promise in controlling impedance increase upon cycling by minimizing side reactions at the electrode-electrolyte interface, the coating layer itself usually exhibits poor Li⁺ conductivity and impedes surface charge transfer. In this work, we have shown that by carefully controlling postannealing temperature of an ultrathin ZrO₂ film prepared by ALD, Zr⁴⁺ surface doping could be achieved for Ni-rich layered oxides to accelerate the charge transfer yet provide sufficient protection. Using single-crystal LiNi_0.6Mn_0.2Co_0.2O₂ as a model material, we have shown that surface Zr⁴⁺ doping combined with ZrO₂ coating can enhance both the cycle performance and rate capability during high-voltage operation. Surface doping via controllable postannealing of ALD surface coating layer reveals an attractive path toward developing stable and Li⁺-conductive interfaces for single-crystal battery materials.

Enhanced Surface Chemical and Structural Stability of Ni-Rich Cathode Materials by Synchronous Lithium-Ion Conductor Coating for Lithium-Ion Batteries

Ni-rich cathode materials LiNi_xCo_yMn_1-x-yO₂ (x ≥ 0.6) have attracted much attention due to their high capacity and low cost. However, they usually suffer from rapid capacity decay and short cycle life due to their surface/interface instability, accompanied by the high Ni content. In this work, with the Ni_0.9Co_0.05Mn_0.05(OH)₂ precursor serving as a coating target, a Li-ion conductor Li₂SiO₃ layer was uniformly coated on Ni-rich cathode material LiNi_0.9Co_0.05Mn_0.05O₂ by a precoating and syn-lithiation method. The uniform Li₂SiO₃ coating layer not only improves the Li-ion diffusion kinetics of the electrode but also reduces mechanical microstrain and stabilizes the surface chemistry and structure with a strong Si-O covalent bond. These results will provide further in-depth understanding on the surface chemistry and structure stabilization mechanisms of Ni-rich cathode materials and help to develop high-capacity cathode materials for next-generation high-energy-density Li-ion batteries.

Guidelines and trends for next-generation rechargeable lithium and lithium-ion batteries

This review article summarizes the current trends and provides guidelines towards next-generation rechargeable lithium and lithium-ion battery chemistries.

Selective TiO2 Nanolayer Coating by Polydopamine Modification for Highly Stable Ni-Rich Layered Oxides

Ni-rich layered oxides are promising cathode materials for developing high-energy lithium-ion batteries. To overcome the major challenge of surface degradation, a TiO₂ surface coating based on polydopamine (PDA) modification was investigated in this study. The PDA precoating layer had abundant OH catechol groups, which attracted Ti(OEt)₄ molecules in ethanol solvent and contributed towards obtaining a uniform TiO₂ nanolayer after calcination. Owing to the uniform coating of the TiO₂ nanolayer, TiO₂ -coated PDA-LiNi_0.6 Co_0.2 Mn_0.2 O₂ (TiO₂ -PNCM) displayed an excellent electrochemical stability during cycling under high voltage (3.0-4.5 V vs. Li⁺ /Li), during which the cathode material undergoes a highly oxidative charge process. In addition, TiO₂ -PNCM exhibited excellent cyclability at elevated temperature (60 °C) compared with the bare NCM. The surface degradation of the Ni-rich cathode material, which is accelerated under harsh cycling conditions, was effectively suppressed after the formation of an ultra-thin TiO₂ coating layer.