Nanotubular structures through templateless electropolymerization using thieno[3,4-b]thiophene derivatives with different substituents and water content

Influence of Polyfluorinated Side Chains and Soft-Template Method on the Surface Morphologies and Hydrophobic Properties of Electrodeposited Films from Fluorene Bridged Dicarbazole Monomers

A clear case of relationship between the monomer molecular structure and the capability of tuning the morphology of electrodeposited gas bubbles template polymer thin films is shown. To this end, a series of fluorene-bridged dicarbazole derivatives containing either linear or terminally branched polyfluorinated side chains connected to the fluorene subunit were synthesized and their electrochemical properties were investigated. The new compounds underwent electrochemical polymerization over indium tin oxide electrodes to give hydrophobic films with nanostructural and morphological properties strongly dependent on the nature of the side chains. Gas bubbles templated electropolymerization was next achieved by the addition of tiny amounts of water to the monomer solutions, without using surfactants. Within the investigated set of molecules, the nanostructural properties of the soft-templated films obtained from monomers bearing linear side chains could be fine-tuned by adjusting electrochemical parameters, leading to superhydrophobic surfaces.

A bioinspired approach to fabricate fluorescent nanotubes with strong water adhesion by soft template electropolymerization and post-grafting

HYPOTHESIS

In this original work, we aim to control both the surface wetting and fluorescence properties of extremely ordered and porous conducting polymer nanotubes prepared by soft template electropolymerization and post-grafting. For reaching this aim, various substituents of different hydrophobicity and fluorescence were post-grafted and the post-grafting yields were evaluated by surface analyses. We show that the used polymer is already fluorescent before post-grafting while the post-grafting yield and as a consequence the surface hydrophobicity highly depend on the substituent.

EXPERIMENTS

Here, we have chosen to chemically grafting various fluorinated and aromatic substituents using a post-grafting in order to keep the same surface topography. Flat conducting polymer surfaces with similar properties have been also prepared for determining the surface energy with the Owens-Wendt equation and estimating the post-grafting yield by X-ray Photoemission Spectroscopy (XPS) and Time of Flight Secondary Emission Spectrometry (ToF-SIMS). For example, using fluorinated chains of various length (C₄F₉, C₆F₁₃ and C₈F₁₇), it is demonstrated that the surface hydrophobicity and oleophobicity do not increase with the fluorinated chain length due to the different post-grafting yields and because of the presence of nanoroughness after post-grafting.

FINDINGS

These surfaces have high apparent water contact angle up to 130.5° but also strong water adhesion, comparable to rose petal effect even if there are no nanotubes on petal surface. XPS and ToF-SIMS analyses provided a detailed characterisation of the surface chemistry with a qualitative classification of the grafted surfaces (F6 > F4 > F8). SEM analysis shows that grafting does not alter the surface morphology. Finally, fluorescence analyses show that the polymer surfaces before post-treatment are already nicely fluorescent. Although the main goal of this paper was and is to understand the role of surface chemistry in tailoring the wetting properties of these surfaces rather than provide specific application examples, we believe that the obtained results can help the development of specific nanostructured materials for potential applications in liquid transport, or in stimuli responsive antimicrobial surfaces.

Electrochemical bubble generation via hydrazine oxidation for the in situ control of an electrodeposited conducting polymer micro/-nanostructure

Herein, a simple, in situ, on step and highly repeatable electrochemical method that allows controlling the nanostructure of electrodeposited polymer films is reported. As an example, the tuning of the electrodeposited polypyrrole nanostructures using inert gas bubbles as the template at the electrode surface generated by the electrochemical oxidation of hydrazine is shown. The hydrazine discharge occurs at a lower potential regarding the beginning of pyrrole electropolymerization process, which allows the modulation of the density and size of the bubbles on the surface electrode controlling electrochemical parameters (applied potential, concentration, time, etc.). Subsequently, the applied potential is moved to where the pyrrole polymerization begins, which induces the material discharges around the bubble template producing polypyrrole hollow structures with definite patterns on the electrode surface. This methodology is proposed as a simple model for the electrodeposition with the morphological control of a wide range of conductive polymers.

An electrochemical method to manipulate the size and density of electrodeposited polypyrrole structures at the micro-nanoscale by the discharge of hydrazine.

A bioinspired strategy for designing well-ordered nanotubular structures by templateless electropolymerization of thieno[3,4-b]thiophene-based monomers

Here, a bioinspired strategy is used to prepare well-ordered nanotubular structures, as observed in animals and plants, such as gecko toe pads or corals. The nanotubes are obtained by templateless electropolymerization of thieno[3,4-b]thiophene-based monomers with various aromatic groups in an organic solvent (dichloromethane). The most interesting and robust structures were obtained with carbazole and pyrene substituents to the base monomer structure, since these groups participate significantly in the polymerization and also have strong π-stacking interactions. The addition of water to electropolymerization solvent significantly impacted the formation of nanotubes, as it caused the release of a significant amount of H₂ and O₂ bubbles, depending on the electropolymerization method. Identifying templateless approaches to vary nanotubular structures is very interesting, as these materials are sought-after for applications in water harvesting systems. This article is part of the theme issue 'Bioinspired materials and surfaces for green science and technology (part 3)'.

Tuning nanotubular structures by templateless electropolymerization with thieno[3,4-b]thiophene-based monomers with different substituents and water content

Here, templateless electropolymerization is employed to produce nanotubular structures from various thieno[3,4-b]thiophene-based monomers that differ in substituent structure and size, as well as the linker connecting the thieno[3,4-b]thiophene core and substituent. The formation of densely packed vertically aligned are obtained from monomers with a pyrene substituent and when a significant amount of water (CH₂Cl₂ + H₂O) is included in the solvent. The geometrical parameters of the nanotubes are highly dependent on the electopolymerization method. A significant amount of air is trapped within the structure of the densely packed open nanotubes obtained with Qs = 100 mC cm^-2 causing an increase in water contact angle (θ_w) up to 82.6° (intermediate state between the Wenzel and the Cassie-Baxter state), and θ_w can become even more hydrophobic by further modifying the deposition method or the electrolyte.