New tabletop SEM-EDS-based approach for cost-efficient monitoring of airborne particulate matter

Characteristics and health implications of fine particulate matter near urban road site in Islamabad, Pakistan

The escalating issue of air pollution has become a significant concern in urban regions, including Islamabad, Pakistan, due to the rise in air pollutant emissions driven by economic and industrial expansion. To gain a deeper understanding of air pollution, a study was conducted during winter 2022-2023, assessing physical, chemical, and biological factors in Islamabad. The findings revealed that the average concentration of fine particulate matter (PM2.5) was notably greater than the World Health Organization (WHO) guidelines, reaching 133.39 μg/m³. Additionally, the average concentration of bacteria (308.64 CFU/m³) was notably greater than that of fungi (203.55 CFU/m³) throughout the study. Analytical analyses, including SEM-EDS and FTIR, showed that the PM2.5 in Islamabad is composed of various particles such as soot aggregates, coal fly ash, minerals, bio-particles, and some unidentified particles. EF analysis distinguished PM2.5 sources, enhancing understanding of pollutants origin, whereas Spearman's correlation analysis elucidated constituent interactions, further explaining air quality impact. The results from the Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-OES) indicated a gradual increase in the total elemental composition of PM2.5 from autumn to winter, maintaining high levels throughout the winter season. Furthermore, a significant variation was found in the mass concentration of PM2.5 when comparing samples collected in the morning and evening. The study also identified the presence of semi-volatile organic compounds (SVOCs) in PM2.5 samples, including polycyclic aromatic hydrocarbons (PAHs) and phenolic compounds, with notable variations in their concentrations. Utilizing health risk assessment models developed by the US EPA, we estimated the potential health risks associated with PM2.5 exposure, highlighting the urgency of addressing air quality issues. These findings provide valuable insights into the sources and composition of PM2.5 in Islamabad, contributing to a comprehensive understanding of air quality and its potential environmental and health implications.

Geochemical distribution and mineralogy of heavy metals in the gasification residue of coal-waste activated carbon-slurry: Insights into leaching behavior

Here, a novel approach to the detoxification and reuse of waste activated carbon (WAC) through co-gasification with coal-water slurry (CWS) is proposed. To evaluate the harmlessness to the environment of this method, the mineralogical composition, leaching characteristics, and geochemical distribution of heavy metals were investigated, enabling the leaching behavior of heavy metals in gasification residues to be explained. The results showed that the gasification residue of coal-waste activated carbon-slurry (CWACS) contained higher concentrations of Cr, Cu, and Zn, while those of Cd, Pb, As, Hg, and Se were well below 100 μg/g. Further, the spatial distributions of Cr, Cu, and Zn in the mineral phases of the gasification residue of CWACS were relatively uniform overall, and no obvious regional enrichment was observed. The leaching concentrations of various heavy metals in the gasification residues of the two CWACS samples were all lower than the standard limit. Following the co-gasification of WAC with CWS, the stability of the heavy metals in the environment was enhanced. Meanwhile, the gasification residues of the two CWACS samples showed no environmental risk for Cr, low environmental risk for Pb and Hg, and only a moderate environmental risk for Cd, As, and Se.

Chemical Characterization of Particulate Matter in the Renaissance City of Ferrara

Atmospheric aerosols are today a key issue in air pollution, mostly related to public health. Two test areas in Ferrara, one in the city center (urban location) and one in the industrial area (industrial location), were studied in June–July 2016 using the SEM technique to identify the environmental impact of some potential pollutant sources. Collection was performed using adhesive tapes applied on the surface of road signs, which allows to select particulate matter moving on air with diffusion movement and to exclude the particles usually deposed by the gravitational process. Dimensional characterization has shown that, usually, smaller particles tend to aggregate themselves in bigger polycrystalline particles with the geometric diameter of up to 10 μm. Micro-analytical data have revealed a wide heterogeneous range of compositions: more abundant silicate followed by carbonate, chlorine, sulphate, carbon, and organic. This preliminary study has highlighted that the Renaissance city of Ferrara is affected by an environmental problem linked to the presence of particulate matter induced by industrial activities, as is the case with some of the most polluted cities in the world. The observations and analytical data pointed out the need for further investigation to better define the features of the fine particulate matter. This will be useful to preserve the cultural heritage of this Medieval-Renaissance city.

Physicochemical and morphological characterization of atmospheric coarse particles by SEM/EDS in new urban central districts of a megacity

Physicochemical and morphological characteristics of atmospheric particles in new urban centers of fast-developing megacities are not well understood. In this study, atmospheric coarse particles (PM_2.5-10) were simultaneously collected in multiple stations (10) in new urban centers, namely Beylikduzu, Buyukcekmece, and Esenyurt, of Istanbul using a modified passive particulate sampling method. Scanning electron microscope and energy dispersive X-photon spectroscopy (SEM-EDS) was used to investigate the size distribution characteristics, chemical composition and their weight percent abundances, and morphological properties of the collected particles. The particle clusters were mainly dominated by Ca-rich Al silicates, Ca dominant, Ca- and S-rich, and NaCl particles, respectively. Their potential sources were assigned to the natural sources (e.g., wind erosion, soil resuspension, and sea sprays) and anthropogenic activities (construction, transportation, mining and crushing, and cement production). In addition to the major contributions (up to 47% of particle number abundance), the minor contribution clusters (less than 1%) with transitional metals rich particles (Fe, Zn, and Cu rich) mainly from anthropogenic sources (combustion, traffic, and vehicular emissions) were identified. The typical size range (> 0.65 to < 11.00 μm) distribution of the major particle clusters fits a left-skewed modal distribution with a peak at 1.10-2.30-μm size range. However, the number of particles decreases significantly with increasing distance to the source, and this justification is stronger for larger size fractions (> 2.3 μm). Particle numbers and varieties indicated significant spatial variations depending upon the identified sources, meteorological factors, and temporal conditions. In general, the results of this study suggest that the passive sampling of PM_2.5-10 coupled with SEM/EDS based single-particle analysis is an effective tool to understand the physicochemical characterization and spatial and temporal variations of atmospheric particles in urban environments.

Choosing the number of images and image position when analyzing the UNC Passive Aerosol Sampler for occupational exposure assessment

The University of North Carolina passive aerosol sampler (UNC sampler) could be an alternative when measuring occupational dust exposure, but the time required for microscopic imaging of the sampler needs to be reduced to make it more attractive. The aims of this study were to (1) characterize the effect on precision when reducing imaging, in order to shorten analysis time and (2) assess if the position of the images makes a difference. Eighty-eight samplers were deployed in different locations of an open pit mine. Sixty images were captured for each UNC sampler, covering 51% of its collection surface, using scanning electron microscopy. Bootstrapped samples were generated with different image combinations, to assess the within-sampler coefficient of variation (CV_ws) for different numbers of images. In addition, the particle concentration relative to the distance from the center of the sampler was studied. Reducing the number of images collected from the UNC sampler led to up to 8.3% CV_ws for 10 images when calculating respirable fraction. As the overall CV has previously been assessed to 36%, the additional contribution becomes minimal, increasing the overall CV to 37%. The mean concentrations of the images were modestly related to distance from the center of the sampler. The CV_ws changed from 8.26% to 8.13% for 10 images when applying rules for the image collection based on distance. Thus, the benefit of these rules on the precision is small and the images can therefore be chosen at random. In conclusion, reducing the number of images analyzed from 60 to 10, corresponding to a reduction of the imaged sampling area from 51% to 8.5%, results in a negligible loss in precision for respirable fraction dust measurements in occupational environments.

Phosphorus Sorption Characteristics in Aluminum-based Water Treatment Residuals Reacted with Dairy Wastewater: 1. Isotherms, XRD, and SEM-EDS Analysis

We examined P sorption characteristics in Al-based water treatment residuals (Al-WTR) generated from slightly alkaline surface water and in an organic residual composite (WW-Al/O-WTR), produced by using the Al-WTR to treat organic-rich and high P concentration dairy wastewater. Solids from both residuals were examined using scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) and X-ray diffraction (XRD), and exposed to P additions of 0 to 4000 mg L in a sorption experiment. The Al-WTR removed ∼97% of the added P, whereas WW-Al/O-WTR removed only 78% of the added P in the addition range of 0 to 100 mg P L. With P additions of ≥100 mg L, the removal rate declined to <38% by Al-WTR and to 16% by WW-Al/O-WTR, possibly implying a change in sorption mechanisms. Analysis by XRD indicated that the major mineral was calcite, with some silica and poorly crystalline Al hydroxides. Analysis by SEM-EDS, which used three-element overlay maps of the residual surfaces, indicated that P was sparsely sorbed on both calcic and Al (hydr)oxide surfaces, along with a few clusters, even at low P concentrations of the treated waters. Ternary clusters of P, Al, and Ca were more abundant on the WW-Al/O-WTR. Carbon distribution suggested that organic substances covered Al surfaces. Sorption of P onto WW-Al/O-WTR may be reversible due to relatively weak Ca-P and Al-P bonds induced by the slight alkaline nature and in the presence of organic moieties, enhancing the WW-Al/O-WTR potential to act as a P source, rather than a P sink, in agricultural applications.

Replacing process water and nitrogen sources with biogas slurry during cellulosic ethanol production

BACKGROUND

Environmental issues, such as the fossil energy crisis, have resulted in increased public attention to use bioethanol as an alternative renewable energy. For ethanol production, water and nutrient consumption has become increasingly important factors being considered by the bioethanol industry as reducing the consumption of these resources would decrease the overall cost of ethanol production. Biogas slurry contains not only large amounts of wastewater, but also the nutrients required for microbial growth, e.g., nitrogen, ammonia, phosphate, and potassium. Therefore, biogas slurry is an attractive potential resource for bioethanol production that could serve as an alternative to process water and nitrogen sources.

RESULTS

In this study, we propose a method that replaces the process water and nitrogen sources needed for cellulosic ethanol production by Zymomonas mobilis with biogas slurry. To test the efficacy of these methods, corn straw degradation following pretreatment with diluted NaOH and enzymatic hydrolysis in the absence of fresh water was evaluated. Then, ethanol fermentation using the ethanologenic bacterial strain Z. mobilis ZMT2 was conducted without supplementing with additional nitrogen sources. After pretreatment with 1.34% NaOH (w/v) diluted in 100% biogas slurry and continuous enzymatic hydrolysis for 144 h, 29.19 g/L glucose and 12.76 g/L xylose were generated from 30 g dry corn straw. The maximum ethanol concentration acquired was 13.75 g/L, which was a yield of 72.63% ethanol from the hydrolysate medium. Nearly 94.87% of the ammonia nitrogen was depleted and no nitrate nitrogen remained after ethanol fermentation. The use of biogas slurry as an alternative to process water and nitrogen sources may decrease the cost of cellulosic ethanol production by 10.0-20.0%. By combining pretreatment with NaOH diluted in biogas slurry, enzymatic hydrolysis, and ethanol fermentation, 56.3 kg of ethanol was produced by Z. mobilis ZMT-2 through fermentation of 1000 kg of dried corn straw.

CONCLUSIONS

In this study, biogas slurry replaced process water and nitrogen sources during cellulosic ethanol production. The results suggest that biogas slurry is a potential alternative to water when pretreating corn straw and, thus, has important potential applications in cellulosic ethanol production from corn straw. This study not only provides a novel method for utilizing biogas slurry, but also demonstrates a means of reducing the overall cost of cellulosic ethanol.

Bio-ethanol production by Zymomonas mobilis using pretreated dairy manure as a carbon and nitrogen source

Dairy manure contains high levels of cellulose, hemicellulose and a nitrogen source.

Fungal spores and pollen in particulate matter collected during agricultural activities in the Po Valley (Italy)

Airborne particulate matter (PM) containing fungal spores and pollen grains was sampled within a monitoring campaign of wheat threshing, plowing and sowing agricultural operations. Fungal spores and pollen grains were detected and identified on morphological basis. No studies were previously available about fungal spore and pollen content in agricultural PM in the Po Valley. Sampling was conducted in a Po Valley farmland in Mezzano (Ferrara, Italy). The organic particles collected were examined by scanning electron microscopy with energy dispersive X-ray spectrometer. Fungal spores and pollen grains were identified when possible at the level of species. The most frequent components of the organic particles sampled were spores of Aspergillus sp., which could represent a risk of developing allergies and aspergillosis for crop farmers.

Properties of agricultural aerosol released during wheat harvest threshing, plowing and sowing

This study shows for the first time a chemical and morphological characterization of agricultural aerosols released during three important agricultural operations: threshing, plowing and sowing. The field campaigns were carried out in the eastern part of the Po Valley, Italy, in summer and autumn 2009. The aerosol particles were sampled on quartz fiber filters and polytetrafluoroethylene membranes in order to allow Inductively Coupled Plasma Mass Spectrometry (ICP-MS) analysis and Scanning Electron Microscopy equipped with an Energy Dispersive X-ray Spectrometer (SEM-EDS) investigations, respectively. The organic carbon mass concentrations were measured with a Sunset Laboratory Dual-Optical Organic Carbone/Elemental Carbon (OCEC) Aerosol analyzer. The morphological and chemical analyses by SEM-EDS allowed recognizing four main particle classes: organic, silica, calcite and clay minerals. The organic particles contribute to both fine and coarse aerosol fractions up to ca. 50% for all three agricultural activities. This was also confirmed by OCEC analysis for fine fraction. Most of the agricultural aerosols, about 60%, were single particles and the remaining 40% were agglomerations of particles. The ICP-MS results showed that threshing and plowing produce more aerosol particles than sowing, which was characterized by important amounts of clay minerals produced from land soils.

Space and time resolved monitoring of airborne particulate matter in proximity of a traffic roundabout in Sweden

Concerns over exposure to airborne particulate matter (PM) are on the rise. Currently monitoring of PM is done on the basis of interpolating a mass of PM by volume (μg/m(3)) but has the drawback of not taking the chemical nature of PM into account. Here we propose a method of collecting PM at its emission source and employing automated analysis with scanning electron microscopy associated with EDS-analysis together with light scattering to discern the chemical composition, size distribution, and time and space resolved structure of PM emissions in a heavily trafficated roundabout in Sweden. Multivariate methods (PCA, ANOVA) indicate that the technogenic marker Fe follows roadside dust in spreading from the road, and depending on time and location of collection, a statistically significant difference can be seen, adding a useful tool to the repertoiré of detailed PM monitoring and risk assessment of local emission sources.

The Progress in Electron Microscopy Studies of Particulate Matters to Be Used as a Standard Monitoring Method for Air Dust Pollution

The present article reviews studies on air solid particles carried out with the use of electron microscopy. Particle analysis combining scanning and transmission electron microscopy (SEM and TEM) can be used to derive size-resolved information of the composition, mixing state, morphology, and complex refractive index of atmospheric aerosol particles. It seems that electron microscopy is more widely used in atmospheric particulate matter analysis, but the usage of this method is sometimes problematic. First of all, there is no standard methodology adapted for dust analysis, and it is difficult to compare the results coming from different laboratories. Nevertheless, it was shown that this method has potential to be used in the future as a standard monitoring procedure of air solid particles.