Co-oxidative removal of arsenite and tetracycline based on a heterogeneous Fenton-like reaction using iron nanoparticles-impregnated biochar

UV-blocking and photocatalytic properties of Ag-coated cotton fabrics with Si binders for photo-degradation of recalcitrant dyes in aqueous solutions under sunlight

Textile wastewater laden with dyes has emerged as a source of water pollution. This possesses a challenge in its effective treatment using a single functional material. In respond to this technological constraint, this work presents multifunctional cotton fabrics (CFs) within a single, streamlined preparation process. This approach utilizes the adherence of Ag NPs (nanoparticles) using Si binder on the surface of CFs, resulting in Ag-coated CFs through a pad dry method. The prepared samples were characterized using scanning electron microscope-energy dispersive X-ray electroscopy (SEM-EDS), thermal gravimetric analysis (TGA), Fourier transformation infrared (FT-IR). It was found that the FT-IR spectra of Ag NPs-coated CFs had peaks appear at 3400, 2900, and 1200 cm-1, implying the stretching vibrations of O-H, C-H, and C-O, respectively. Based on the EDX analysis, the presence of C, O, and Ag related to the coated CFs were detected. After coating the CFs with varying concentrations of Ag NPs (1%, 2% and 3% (w/w)), they were used to remove dyes. Under the same concentration of 10 mg/L and optimized pH 7.5 and 2 h of reaction time, 3% (w/w) Ag-coated CFs exhibited a substantial MB degradation of 98 %, while removing 95% of methyl orange, 85% of rhodamine B, and 96% of Congo red, respectively, following 2 h of Vis exposure. Ag NPs had a strong absorption at 420 nm with 2.51 eV of energy band gap. Under UV irradiation, electrons excited and produced free radicals that promoted dyes photodegradation. The oxidation by-products included p-dihydroxybenzene and succinic acid. Spent Ag-coated CFs attained 98% of regeneration efficiency. The utilization of Ag-coated CFs as a photocatalyst facilitated treated effluents to meet the required discharge standard of lower than 1 mg/L mandated by national legislation. The integration of multifunctional CFs in the treatment system presents a new option for tackling water pollution due to dyes.

Leveraging food waste for electricity: A low-carbon approach in energy sector for mitigating climate change and achieving net zero emission in Hong Kong (China)

In recent years, food waste has been a global concern that contributes to climate change. To deal with the rising impacts of climate change, in Hong Kong, food waste is converted into electricity in the framework of low-carbon approach. This work provides an overview of the conversion of food waste into electricity to achieve carbon neutrality. The production of methane and electricity from waste-to-energy (WTE) conversion are determined. Potential income from its sale and environmental benefits are also assessed quantitatively and qualitatively. It was found that the electricity generation from the food waste could reach 4.33 × 109 kWh annually, avoiding equivalent electricity charge worth USD 3.46 × 109 annually (based on US' 8/kWh). An equivalent CO2 mitigation of 9.9 × 108 kg annually was attained. The revenue from its electricity sale in market was USD 1.44×109 in the 1st year and USD 4.24 ×109 in the 15th year, respectively, according to the projected CH4 and electricity generation. The modelling study indicated that the electricity production is 0.8 kWh/kg of landfilled waste. The food waste could produce electricity as low as US' 8 per kW ∙ h. In spite of its promising results, there are techno-economic bottlenecks in commercial scale production and its application at comparable costs to conventional fossil fuels. Issues such as high GHG emissions and high production costs have been determined to be resolved later. Overall, this work not only leads to GHG avoidance, but also diversifies energy supply in providing power for homes in the future.

Hydrochar-nanoparticle integration for arsenic removal from wastewater: Challenges, possible solutions, and future horizon

Arsenic (As) contamination poses a significant threat to human health, ecosystems, and agriculture, with levels ranging from 12 to 75% attributed to mine waste and stream sediments. This naturally element is abundant in Earth's crust and gets released into the environment through mining and rock processing, causing ≈363 million people to depend on As-contaminated groundwater. To combat this issue, introducing a sustainable hydrochar system has achieved a remarkable removal efficiency of over 92% for arsenic through adsorption. This comprehensive review presents an overview of As contamination in the environment, with a specific focus on its impact on drinking water and wastewater. It delves into the far-reaching effects of As on human health, ecosystems, aquatic systems, and agriculture, while also exploring the effectiveness of existing As treatment systems. Additionally, the study examines the potential of hydrochar as an efficient adsorbent for As removal from water/wastewater, along with other relevant adsorbents and biomass-based preparations of hydrochar. Notably, the fusion of hydrochar with nanoparticle-centric approaches presents a highly promising and environmentally friendly solution for achieving the removal of As from wastewater, exceeding >99% efficiency. This innovative approach holds immense potential for advancing the realms of green chemistry and environmental restoration. Various challenges associated with As contamination and treatment are highlighted, and proposed solutions are discussed. The review emphasizes the urgent need to advance treatment technologies, improve monitoring methods, and enhance regulatory frameworks. Looking outlook, the article underscores the importance of fostering research efforts, raising public awareness, and fostering interdisciplinary collaboration to address this critical environmental issue. Such efforts are vital for UN Sustainable Development Goals, especially clean water and sanitation (Goal 6) and climate action (Goal 13), crucial for global sustainability.

Resource recovery and valorization of food wastewater for sustainable development: An overview of current approaches

The food processing industry is one of the world's largest consumers of potable water. Agri-food wastewater systems consume about 70% of the world's fresh water and cause at least 80% of deforestation. Food wastewater is characterized by complex composition, a wide range of pollutants, and fluctuating water quality, which can cause huge environmental pollution problems if discharged directly. In recent years, food wastewater has attracted considerable attention as it is considered to have great prospects for resource recovery and reuse due to its rich residues of nutrients and low levels of harmful substances. This review explored and compared the sources and characteristics of different types of food wastewater and methods of wastewater treatment. Particular attention was paid to the different methods of resource recovery and reuse of food wastewater. The diversity of raw materials in the food industry leads to different compositional characteristics of wastewater, which determine the choice and efficiency of wastewater treatment methods. Physicochemical methods, and biological methods alone or in combination have been used for the efficient treatment of food wastewater. Current approaches for recycling and reuse of food wastewater include culture substrates, agricultural irrigation, and bio-organic fertilizers, recovery of high-value products such as proteins, lipids, biopolymers, and bioenergy to alleviate the energy crisis. Food wastewater is a promising substrate for resource recovery and reuse, and its valorization meets the current international policy requirements regarding food waste and environment protection, follows the development trend of the food industry, and is also conducive to energy conservation, emission reduction, and economic development. However, more innovative biotechnologies are necessary to advance the effectiveness of food wastewater treatment and the extent of resource recovery and valorization.

Fabrication, characterization, and application of light weight thermal insulation material from combined buffing dust and plaster of paris for construction industry

Buffing dust, generated from tannery industries, is a source of air pollution in Pakistan. Valorization of the waste into another useful material is important to deal with the environmental pollution, while reducing waste disposal costs in landfills. To demonstrate its technological strength, this work fabricates a thermal insulation material made of plaster of Paris and the buffing dust (from tanning waste) in the form of a composite with superior mechanical properties and low thermal conductivity. Buffing dust with concentrations ranging from 5 to 20% (w/w) were loaded in the composite. The samples synthesized were made slurry of plaster of Paris, buffing dust, and water at ambient temperature. The physico-mechanical properties of composite were analyzed. It was found that the composite had better thermal insulation properties than the panels of the plaster of Paris. Its thermal conductivity was reduced to 15% after adding buffing dust (20% w/w). All the materials had physico-chemical properties like tensile strength (0.02 MPa and 0.06 MPa), density (700-400 kg/m3), water absorption (5.2-8.6%) and thermal conductivity (0.17000-0.09218 W/m-K). Thermogravimetric analysis showed that the material was thermally stable at temperatures ranging from 145 to 177 °C, while FT-IR results revealed that the composite contained O-H, N-H, and CO functional groups. SEM analysis displayed that the composite's homogeneity was reduced with low voids due to buffing dust addition, while EDX analysis showed that the composite contained 23.62% of S, 26.76% of Ca, 49.2% of O and 0.42% of C. This implies that buffing dust could be recycled to manufacture heat insulation materials for construction sector to reduce air pollution, while minimizing energy consumption. By integrating the buffing dust from tanning waste and the plaster of Paris as a composite for construction sector, this work promotes the recycling of unused waste, while saving public funds. Instead of paying landfill fees and polluting soil, the waste may be recycled at lower cost, while reducing environmental damage.

Tackling microplastics pollution in global environment through integration of applied technology, policy instruments, and legislation

Microplastic pollution is a serious environmental problem that affects both aquatic and terrestrial ecosystems. Small particles with size of less than 5 mm, known as microplastics (MPs), persist in the environment and pose serious threats to various species from micro-organisms to humans. However, terrestrial environment has received less attention than the aquatic environment, despite being a major source of MPs that eventually reaches water body. To reflect its novelty, this work aims at providing a comprehensive overview of the current state of MPs pollution in the global environment and various solutions to address MP pollution by integrating applied technology, policy instruments, and legislation. This review critically evaluates and compares the existing technologies for MPs detection, removal, and degradation, and a variety of policy instruments and legislation that can support the prevention and management of MPs pollution scientifically. Furthermore, this review identifies the gaps and challenges in addressing the complex and diverse nature of MPs and calls for joint actions and collaboration from stakeholders to contain MPs. As water pollution by MPs is complex, managing it effectively requires their responses through the utilization of technology, policy instruments, and legislation. It is evident from a literature survey of 228 published articles (1961-2023) that existing water technologies are promising to remove MPs pollution. Membrane bioreactors and ultrafiltration achieved 90% of MPs removal, while magnetic separation was effective at extracting 88% of target MPs from wastewater. In biological process, one kg of wax worms could consume about 80 g of plastic/day. This means that 100 kg of wax worms can eat about 8 kg of plastic daily, or about 2.9 tons of plastic annually. Overall, the integration of technology, policy instrument, and legislation is crucial to deal with the MPs issues.

Fabrication, characterization, and application of BiOI@ZIF-8 nanocomposite for enhanced photocatalytic degradation of acetaminophen from aqueous solutions under UV-vis irradiation

This work investigates the use of novel BiOI@ZIF-8 nanocomposite for the removal of acetaminophen (Ace) from synthetic wastewater. The samples were analyzed using FTIR, XRD, XPS, DRS, PL, FESEM-EDS, and ESR techniques. The effects of the loading capacity of ZIF-8 on the photocatalytic oxidation performance of bismuth oxyiodide (BiOI) were studied. The photocatalytic degradation of Ace was maximized by optimizing pH, reaction time and the amount of photocatalyst. On this basis, the removal mechanisms of the target pollutant by the nanocomposite and its photodegradation pathways were elucidated. Under optimized conditions of 1 g/L of composite, pH 6.8, and 4 h of reaction time, it was found that the BiOI@ZIF-8 (w/w = 1:0.01) nanocomposite exhibited the highest Ace removal (94%), as compared to that of other loading ratios at the same Ace concentration of 25 mg/L. Although this result was encouraging, the treated wastewater still did not satisfy the required statutory of 0.2 mg/L. It is suggested that the further biological processes need to be adopted to complement Ace removal in the samples. To sustain its economic viability for wastewater treatment, the spent composite still could be reused for consecutive five cycles with 82% of regeneration efficiency. Overall, this series of work shows that the nanocomposite was a promising photocatalyst for Ace removal from wastewater samples.

N,S-codoped biochar outperformed N-doped biochar on co-activation of H2O2 with trace dissolved Fe(Ⅲ) for enhanced oxidation of organic pollutants

Co-activation of H2O2 with biochar and iron sources together provides an attractive strategy for efficient removal of refractory pollutants, because it can solve the problems of slow Fe(Ⅱ) regeneration in Fenton/Fenton-like processes and of low •OH yield in biochar-activated process. In this study, a wood-derived biochar (WB) was modified by heteroatom doping for the objective of enhancing its reactivity toward co-activation of H2O2. The performance of the co-activated system using doped biochars and trace dissolved Fe(Ⅲ) on oxidation of organic pollutants was evaluated for the first time. The characterizations using X-ray photoelectron spectroscopy (XPS), Raman spectra and electrochemical analyses indicate that heteroatom doping introduced more defects in biochar and improved its electron transfer capacity. The oxidation experiments show that heteroatom doping improved the performance of biochar in the co-activated process, in which the N,S-codoped biochar (NSB) outperformed the N-doped biochar (NB) on oxidation of pollutants. The reaction rate constant (kobs) for oxidation of sulfadiazine in NSB + Fe + H2O2 is 2.25 times that in NB + Fe + H2O2, and is 72.9 times that in the Fenton-like process without biochar, respectively. The mechanism investigations indicate that heteroatom doping enhanced biochar's reactivity on catalyzing the decomposition of H2O2 and on reduction of Fe(Ⅲ) due to the improved electron transfer/donation capacity. In comparison with N-doping, N,S-codoping provided additional electron donor (thiophenic C-S-C) for faster regeneration of Fe(Ⅱ) with less amount of doping reagent used. Furthermore, co-activation with NSB maintained to be efficient at a milder acidic pH than Fenton/Fenton-like processes, and can be used for oxidation of different pollutants and in real water. Therefore, this research provides a novel, sustainable and cost-efficient method for oxidation of refractory pollutants.

Decarbonization in waste recycling industry using digitalization to promote net-zero emissions and its implications on sustainability

Digitalization and sustainability have been considered as critical elements in tackling a growing problem of solid waste in the framework of circular economy (CE). Although digitalization can enhance time-efficiency and/or cost-efficiency, their end-results do not always lead to sustainability. So far, the literatures still lack of a holistic view in understanding the development trends and key roles of digitalization in waste recycling industry to benefit stakeholders and to protect the environment. To bridge this knowledge gap, this work systematically investigates how leveraging digitalization in waste recycling industry could address these research questions: (1) What are the key problems of solid waste recycling? (2) How the trends of digitalization in waste management could benefit a CE? (3) How digitalization could strengthen waste recycling industry in a post-pandemic era? While digitalization boosts material flows in a CE, it is evident that utilizing digital solutions to strengthen waste recycling business could reinforce a resource-efficient, low-carbon, and a CE. In the Industry 4.0 era, digitalization can add 15% (about USD 15.7 trillion) to global economy by 2030. As digitalization grows, making the waste sector shift to a CE could save between 30% and 35% of municipalities' waste management budget. With digitalization, a cost reduction of 3.6% and a revenue increase of 4.1% are projected annually. This would contribute to USD 493 billion in an increasing revenue yearly in the next decade. As digitalization enables tasks to be completed shortly with less manpower, this could save USD 421 billion annually for the next decade. With respect to environmental impacts, digitalization in the waste sector could reduce global CO₂ emissions by 15% by 2030 through technological solutions. Overall, this work suggests that digitalization in the waste sector contributes net-zero emission to a digital economy, while transitioning to a sustainable world as its social impacts.

Source, occurrence, distribution, fate, and implications of microplastic pollutants in freshwater on environment: A critical review and way forward

The generation of microplastics (MPs) has increased recently and become an emerging issue globally. Due to their long-term durability and capability of traveling between different habitats in air, water, and soil, MPs presence in freshwater ecosystem threatens the environment with respect to its quality, biotic life, and sustainability. Although many previous works have been undertaken on the MPs pollution in the marine system recently, none of the study has covered the scope of MPs pollution in the freshwater. To consolidate scattered knowledge in the literature body into one place, this work identifies the sources, fate, occurrence, transport pathways, and distribution of MPs pollution in the aquatic system with respect to their impacts on biotic life, degradation, and detection techniques. This article also discusses the environmental implications of MPs pollution in the freshwater ecosystems. Certain techniques for identifying MPs and their limitations in applications are presented. Through a literature survey of over 276 published articles (2000-2023), this study presents an overview of solutions to the MP pollution, while identifying research gaps in the body of knowledge for further work. It is conclusive from this review that the MPs exist in the freshwater due to an improper littering of plastic waste and its degradation into smaller particles. Approximately 15-51 trillion MP particles have accumulated in the oceans with their weight ranging between 93,000 and 236,000 metric ton (Mt), while about 19-23 Mt of plastic waste was released into rivers in 2016, which was projected to increase up to 53 Mt by 2030. A subsequent degradation of MPs in the aquatic environment results in the generation of NPs with size ranging from 1 to 1000 nm. It is expected that this work facilitates stakeholders to understand the multi-aspects of MPs pollution in the freshwater and recommends policy actions to implement sustainable solutions to this environmental problem.

Challenges and opportunities for biochar to promote circular economy and carbon neutrality

Biochar, derived from unused biomass, is widely considered for its potential to deal with climate change problems. Global interest in biochar is attributed to its ability to sequester carbon in soil and to remediate aquatic environment from water pollution. As soil conditioner and/or adsorbent, biochar offers opportunity through a circular economy (CE) paradigm. While energy transition continues, progress toward low-emissions materials accelerates their advance towards net-zero emissions. However, none of existing works addresses CE-based biochar management to achieve carbon neutrality. To reflect its novelty, this work provides a critical overview of challenges and opportunities for biochar to promote CE and carbon neutrality. This article also offers seminal perspectives about strengthening biomass management through CE and resource recovery paradigms, while exploring how the unused biomass can promote net zero emissions in its applications. By consolidating scattered knowledge in the body of literature into one place, this work uncovers new research directions to close the loops by implementing the circularity of biomass resources in various fields. It is conclusive from a literature survey of 113 articles (2003-2023) that biomass conversion into biochar can promote net zero emissions and CE in the framework of the UN Sustainable Development Goals (SDGs). Depending on their physico-chemical properties, biochar can become a suitable feedstock for CE. Biochar application as soil enrichment offsets 12% of CO₂ emissions by land use annually. Adding biochar to soil can improve its health and agricultural productivity, while minimizing about 1/8 of CO₂ emissions. Biochar can also sequester CO₂ in the long-term and prevent the release of carbon back into the atmosphere after its decomposition. This practice could sequester 2.5 gigatons (Gt) of CO₂ annually. With the global biochar market reaching USD 368.85 million by 2028, this work facilitates biochar with its versatile characteristics to promote carbon neutrality and CE applications.

Influence of Fe2O3 and bacterial biofilms on Cu(II) distribution in a simulated aqueous solution: A feasibility study to sediments in the Pearl River Estuary (PR China)

This study investigated physico-chemical interactions among Cu(II), biogenic materials, and Fe₂O₃ in a continuous-flow biofilm reactor system under a well-controlled environment. The effects of Fe₂O₃ and bacterial biofilms on the distribution of Cu(II) in a simulated aquatic environment were studied. To control biological and abiotic elements in the marine environment, a biofilm reactor was designed to understand the metal speciation of Cu(II) and its distribution. The reactor consisted of a biofilm chamber equipped with glass slides for biofilms attachment. Due to its ability to grow as biofilm in the medium, Pseudomonas atlantica was cultivated to adsorb trace Cu(II) to attached and suspended cells. It was found that biofilms with 170-285 mequiv chemical oxygen demand (COD) concentration/m² of total oxidizable materials accelerated the Cu(II) adsorption to the surface of the reactor significantly by a factor of five. A significant inhibition to the bacterial growth took place (p ≤ 0.05; t-test) when Cu(II) concentration was higher than 0.5 mg/L. In the absence of Cu(II), bacterial cells grew normally to 0.075 of optical density (OD). However, at the Cu(II) concentration of 0.2 mg/L, the cells grew to a lower OD of 0.58. The presence of glycine and EDTA substantially reduced the toxicity of Cu(II) on bacterial growth (p ≤ 0.05; paired t-test). Their complexation with Cu(II) rendered the metal ions less available to bacterial cells. This implies that the Fe₂O₃ and bacterial biofilm affected Cu(II) distribution and speciation in the aquatic environment.

Removal of arsenic from semiarid area groundwater using a biosorbent from watermelon peel waste

Groundwater is one of the most important reservoirs in semi-arid and arid zones of the world, particularly in Mexico. The aims of this work were to produce a biosorbent from watermelon peel waste and a biosorbent with citric acid treatment and to evaluate both biosorbents with different concentrations of arsenic in groundwater. The biosorbents were produced with watermelon peel residues, which were observed by SEM microscopy to evaluate their physical morphology. Its removal potential was tested at concentrations of 0, 1, 13, 22, and 65 μg/L of arsenic, and both adsorption capacity and removal percentage were analyzed by final measurement obtained by atomic absorption spectrometry. The pH was measured throughout the experimentation maintaining ranges between 5.5 and 7.5. The biosorbent without treatment presented clearer and more compact flakes. At the microscopic level, the biosorbent without treatment presented pores with a more circular shape, and the biosorbent with treatment was more polygonal, similar to a honeycomb. The highest removal percentage was 99.99%, for both treatments at 4 h. The biosorbent without treatment at 4 h with arsenic concentrations of 65 μg/L presented the highest adsorption capacity (2.42 μg/g). It is concluded that watermelon peel biosorbent is a material that has the potential to remove arsenic from groundwater. This type of biosorbent is effective to remove arsenic and could be used in the field, however, it still needs to be optimized to convert it into a material completely suitable for large-scale use.

Macro-nutrients recovery from liquid waste as a sustainable resource for production of recovered mineral fertilizer: Uncovering alternative options to sustain global food security cost-effectively

Global food security, which has emerged as one of the sustainability challenges, impacts every country. As food cannot be generated without involving nutrients, research has intensified recently to recover unused nutrients from waste streams. As a finite resource, phosphorus (P) is largely wasted. This work critically reviews the technical applicability of various water technologies to recover macro-nutrients such as P, N, and K from wastewater. Struvite precipitation, adsorption, ion exchange, and membrane filtration are applied for nutrient recovery. Technological strengths and drawbacks in their applications are evaluated and compared. Their operational conditions such as pH, dose required, initial nutrient concentration, and treatment performance are presented. Cost-effectiveness of the technologies for P or N recovery is also elaborated. It is evident from a literature survey of 310 published studies (1985-2022) that no single technique can effectively and universally recover target macro-nutrients from liquid waste. Struvite precipitation is commonly used to recover over 95 % of P from sludge digestate with its concentration ranging from 200 to 4000 mg/L. The recovered precipitate can be reused as a fertilizer due to its high content of P and N. Phosphate removal of higher than 80 % can be achieved by struvite precipitation when the molar ratio of Mg²⁺/PO₄^3- ranges between 1.1 and 1.3. The applications of artificial intelligence (AI) to collect data on critical parameters control optimization, improve treatment effectiveness, and facilitate water utilities to upscale water treatment plants. Such infrastructure in the plants could enable the recovered materials to be reused to sustain food security. As nutrient recovery is crucial in wastewater treatment, water treatment plant operators need to consider (1) the costs of nutrient recovery techniques; (2) their applicability; (3) their benefits and implications. It is essential to note that the treatment cost of P and/or N-laden wastewater depends on the process applied and local conditions.

Damage and elimination of soil and water antibiotic and heavy metal pollution caused by livestock husbandry

The combination of antibiotics and heavy metals (HMs) increases the toxicity range of influence and requires additional research attention. This article analyzed the toxicity mechanisms and damage of combined pollution. Cross-resistance, co-resistance, and co-regulation are the primary toxicity mechanisms. Combined pollution increases antibiotic resistance genes (ARGs), increases bacterial resistance, and promotes the horizontal transfer of ARGs, affecting the types and distribution of microorganisms. The hazard of combined pollution varies with concentration and composition. The physicochemical and biological technologies for eliminating combined pollution are primarily elaborated. Adsorption, photocatalytic degradation, and microbial treatment show high removal rates and good recyclability, indicating good application potential. This review provides a basis and reference for the further study the elimination of combined antibiotic and HM pollution.

Evaluation of iron-loaded granular activated carbon used as heterogeneous fenton catalyst for degradation of tetracycline

To optimize the efficiency of general adsorption-Fenton oxidation treatment, iron-loaded granular activated carbon (Fe-GAC) was prepared, characterized, and used as a catalyst in the heterogeneous Fenton oxidation of tetracycline (TC). Characterization revealed that the Fe(II) was successfully introduced onto the original granular activated carbon (GAC) and diversified the materials' surface morphology and elemental compounds. Under an initial pH of 3.0, the Fe-GAC/Fenton system obtained a maximum removal rate of 92.6%, with hydrogen peroxide (H₂O₂) dosages of 9 mmol g^-1. And the GAC/Fenton without iron supplementation was 89.5%, with H₂O₂ dosages of 8 mmol g^-1. Additionally, the Fe-GAC/Fenton system consumed a lower Fe(II) dosage than GAC/Fenton, with Fe(II)/H₂O₂ molar ratios of 0.007:1 and 0.04:1, respectively. Analysis of total organic carbon demonstrated higher mineralization efficiency in the Fe-GAC/Fenton system (67.2%), which was approximately 1.3 times of GAC/Fenton. Desorption experiments showed that the adsorption and degradation accounted for 19.22% and 80.78% of the total TC removal by GAC/Fenton, and 10.58% and 89.42% in the Fe-GAC/Fenton system, respectively. Electron paramagnetic resonance (EPR) technique and quenching experiments demonstrated that the dominant reactive oxygen species (ROS) in synergistic treatments were hydroxyl (•OH) and hydroxy peroxyl (HO₂•) radicals. In addition, three potential degradation pathways for TC were proposed according to the detected fourteen intermediates. Catalyst regeneration treatments were evaluated over six cycles, and the regeneration was 6.5% higher with the iron-supplemented carbon granules. Overall, the Fe-GAC can be used as an efficient catalyst in practical water treatment, and this study demonstrated a promising method to develop adsorption-Fenton technology.

Biosorption of heavy metals from aqueous solutions using activated sludge, Aeromasss hydrophyla, and Branhamella spp based on modeling with GEOCHEM

This work tests the technical applicability of sewage sludge and isolated dead cells of Aeromasss hydrophyla and Branhamella spp for the elimination of inorganic pollutants such as Zn(II), Pb(II), Cd(II), and/or Cu(II) using synthetic wastewater with their initial concentrations of 100 mg/L, respectively. The sludge samples were collected from local sewage treatment plants. The effects of dose and pH on heavy metals removal were evaluated in batch studies and their removal performances were compared to those of previous studies. Both the Freundlich and the Langmuir models were plotted to study their biosorption using activated sludge and the bacteria. Isotherm data, resulting from the batch studies, were compared to the modeling results of Geochem. It was evident that the activated sludge could achieve 99% of Zn(II), Cd(II), Cu(II) and Pb(II) removal with 100 mg/L of concentration at pH 6.0 and 3 g/L of dose. Under the same conditions, 97% of Cd(II), Cu(II) and/or Pb(II) was removed by Aeromasss hydrophyla and Branhamella spp, as indicated by their adsorption capacities (activated sludge: 99.07 mg Pb²⁺/g; dewatered sludge: 57.15 mg Pb²⁺/g; digested sludge: 83.58 mg Pb²⁺/g; 24.47 mg Cd²⁺/g; Aeromasss hydrophylla: 71.91 mg Pb²⁺/g; Branhamella spp: 37.52 mg Cu²⁺/g). Of the four heavy metals studied, Pb(II) had the highest metal adsorption capacity for all adsorbents studied (Pb²⁺>Cu²⁺> Cd²⁺>Zn²⁺). The modeling results of the Geochem fitted well with the isotherm data of the batch studies at varying concentrations from 20 to 100 mg/L. The thermodynamic constant at pH 4 were comparable to those obtained from previous works. This indicates a reliable prediction over varying metal concentrations and pHs of the batch studies. In spite of the promising results, the treated effluents still could not meet the required effluent limits set by local legislation. Therefore, it is necessary to subsequently treat the samples using biological processes such as activated sludge.

Electronic structure modulation of multi-walled carbon nanotubes using azo dye for inducing non-radical reaction: Effect of graphitic nitrogen and structural defect

Multiwalled carbon nanotube (MWCNT) have a great potential for advanced oxidation process as a metal free catalyst. However, there catalytic activity is very low and needs to be appropriately tuned. Herein, we demonstrate a novel synthesis method for tuning the defect and surface functionality of MWCNT using azo dyes and the catalytic performance was tested for the degradation of different organic contaminates using PMS as an oxidant. The content, type of heteroatom functional groups, and the defect parameters were optimized by varying the pH and concentration of the organic dye. The quenching effect showed that singlet oxygen (¹O₂) is the primary reactive species generated by graphitic nitrogen, which can be boosted by the degree of graphitic structure disruption in MWCNT. The Linear sweep voltammetry (LSV) also confirmed that extrinsic doping enhanced the non-radical degradation by increasing the direct charge transfer rate from MB to PMS. Moreover, the designed catalyst showed a fast degradation performance with 35.1 kJ/mol activation energy and achieved the highest dye degradation rate and even surpassed some state-of-the-art metal-based and metal-free catalysts. The effect of inorganic anions study has also confirmed its industrial applicability.

Self-cleaning MnZn ferrite/biochar adsorbents for effective removal of tetracycline

A renewable tri-metallic spinel decorated biochar adsorbent (MZF-BC) was fabricated by a facile hydrothermal method and to remove tetracycline. The physicochemical properties of MZF-BC were well studied. MZF-BC with a hybrid pore structure of mesopores (~7.6 nm) and macropores (~50 nm) has the maximum tetracycline adsorption capacity reaching 142.4 mg g^-1. Through the study of adsorption kinetics, isotherms and key influencing factors, it was found that MZF-BC adsorption on tetracycline was primarily multi-layer effect with the initial adsorption behavior of pore filling associated with hydrogen bonding and π-π stacking. Furthermore, the MZF-BC performs excellent regeneration ability by driving Fenton-like catalysis as the self-cleaning process in the liquid phase. This study contributes to a new insight into the in-situ regeneration of biochar-based adsorbents after adsorbing organic pollutants in pharmaceutical wastewater treatment.

Improved photodegradation of antibiotics pollutants in wastewaters by advanced oxidation process based on Ni-doped TiO2

The number of antibiotic compounds in wastewaters has been growing globally due to the covid-19 problem. Using antibiotics to treat the patients would produce larger amounts of these compounds into the environment with negative impacts. Hence, finding out the method for the elimination of toxic organic pollutants as well as antibiotics in water is urgent (In this study, the treatment of antibiotic pollutants including cefalexin (CF) and tetracycline (TC) was investigated by applying the advanced oxidation process based on Ni-doped TiO₂ (Ni-TiO₂). The characterizations technologies such as XRD, XPS, UV-vis, PL, and PC indicated that Ni doping would improve the photocatalytic performance of TiO₂. In the photodegradation experiments, the Ni-TiO₂ possessed high photocatalytic degradation efficiencies with 93.6% for CF and 82.5% for TC. Besides, the removal rates of antibiotics after five cycles are higher than 75%, implying excellent stability of Ni-TiO₂ photocatalyst. The result from the treatment of wastewater samples revealed that the Ni-TiO₂ photocatalytic had good performance for removal of CF and TC at a high level of 88.6 and 80.2%, respectively.

Synthetic organic antibiotics residues as emerging contaminants waste-to-resources processing for a circular economy in China: Challenges and perspective

Synthetic antibiotics have been known for years to combat bacterial antibiotics. But their overuse and resistance have become a concern recently. The antibiotics reach the environment, including soil from the manufacturing process and undigested excretion by cattle and humans. It leads to overburden and contamination of the environment. These organic antibiotics remain in the environment for a very long period. During this period, antibiotics come in contact with various flora and fauna. The ill manufacturing practices and inadequate wastewater treatment cause a severe problem to the water bodies. After pretreatment from pharmaceutical industries, the effluents are released to the water bodies such as rivers. Even after pretreatment, effluents contain a significant number of antibiotic residues, which affect the living organisms living in the water bodies. Ultimately, river contaminated water reaches the ocean, spreading the contamination to a vast environment. This review paper discusses the impact of synthetic organic contamination on the environment and its hazardous effect on health. In addition, it analyzes and suggests the biotechnological strategies to tackle organic antibiotic residue proliferation. Moreover, the degradation of organic antibiotic residues by biocatalyst and biochar is analyzed. The circular economy approach for waste-to-resource technology for organic antibiotic residue in China is analyzed for a sustainable solution. Overall, the significant challenges related to synthetic antibiotic residues and future aspects are analyzed in this review paper.

Treatment of As(III)-Laden Contaminated Water Using Iron-Coated Carbon Fiber

This work presents the fabrication, characterization, and application of iron-coated carbon fiber (Fe@CF), synthesized in a facile in situ iron reduction, for As(III) removal from an aqueous solution. The physico-chemical properties of the composite were characterized using Brunauer–Emmett–Teller (BET) surface area, scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier-transform infrared (FTIR) spectroscopy. Adsorption studies were evaluated in batch experiments with respect to reaction time, the dose of adsorbent, As(III) initial concentration, pH, and co-existing ions. The results showed that the BET surface area and pore volume of Fe@CF slightly decreased after Fe coating, while its pore size remained, while the SEM and XRD analyses demonstrated that the Fe was successfully anchored on the CF. A maximum As(III) adsorption of 95% was achieved with an initial As concentration of 1.5 mg/L at optimum conditions (30 min of reaction time, 1 g/L of dose, 1 mg/L of As(III) concentration, and pH 3.5). Since the treated effluents could not meet the strict discharge standard of ≤10 μg/L set by the World Health Organization (WHO), a longer reaction time is required to complete the removal of remaining As(III) in the wastewater effluents. As compared to the other adsorbents reported previously, the Fe@CF composite has the highest As(III) removal. Overall, the findings suggested that the use of Fe@CF as an adsorbent is promising for effective remediation in the aquatic environment.

Efficient utilization of the electron energy of antibiotics to accelerate Fe(III)/Fe(II) cycle in heterogeneous Fenton reaction induced by bamboo biochar/schwertmannite

The discharge of antibiotics evokes environmental health crisis, and is also a waste of organic energy. Currently, heterogeneous Fenton for antibiotics removal has attracted growing attentions due to wide pH range and no iron sludge production, however, it often suffers from a low formation rate of Fe(II), resulting in difficult application of heterogeneous Fenton technology in sewage treatment. To overcome this drawback, bamboo biochar (BB) is coupled with schwertmannite (Sch) through Acidithiobacillus ferrooxidans-mediated Fe(II) oxidation reaction to obtain a heterogeneous catalyst (Sch/BB) with high adsorption performance and Fenton activity. According to the analysis of experimental results, electrons around C (from BB) can easily transfer to Fe by Fe-O-C bonds to expedite ≡Fe(III)/≡Fe(II) cycle, while electrons of antibiotics adsorbed on Sch/BB surface are effectively utilized to maintain the efficient regeneration of ≡Fe(II) through BB electron shuttle or Fe-O-C bonds between Sch/BB and pollutants, further causing a superior Fenton activity (98% antibiotics removal) of Sch/BB. Moreover, due to its excellent adsorption performance, Sch/BB as filter materials can effectively remove dye pollutants in flow wastewater. These findings provided a high-activity and practical heterogeneous Fenton catalyst for pollutants degradation, while a new perspective for efficient utilization of the electrons of organic pollutants was given.

Transformation of Solid Waste Management in China: Moving towards Sustainability through Digitalization-Based Circular Economy

In China, environmental pollution due to municipal solid waste (MSW) over-generation is one of the country’s priority concerns. The increasing volume and complexity of the waste poses serious risks to the environment and public health. Currently, the annual growth of MSW generation is estimated to be approximately 8–10% and will increase to 323 million metric tons (Mt) by 2030. Based on the secondary data collected from a literature survey, this article critically evaluates the recent progress of MSW management (MSWM) in China and offers new insights into the waste sector in the era of Industry 4.0. This helps decision makers in China to plan a smooth transition nationwide to a circular economy (CE) in the waste sector. It is evident that digitalization is a driving force for China to move towards low-carbon development strategies within the framework of CE. Through digitalization, the waste sector has promoted prevention, reduction, reuse, and recycling (3Rs) of waste before waste disposal in landfills. A proper implementation of digitalization-based waste recycling has contributed to an efficient cooperation between the government and private sector, increased job opportunities, and promoted the conservation of resources. It is anticipated that this work not only contributes to the establishment of an integrated MSWM system in China, but also improves local MSWM through digitalization in the framework of a CE.

Aqueous Arsenic Speciation with Hydrogeochemical Modeling and Correlation with Fluorine in Groundwater in a Semiarid Region of Mexico

In arid and semiarid regions, groundwater becomes the main source to meet the drinking water needs of large cities, food production, and industrial activities. For this reason, necessary studies must be carried out to estimate its quantity and quality, always seeking sustainable management, thus avoiding social conflicts or a decrease in the productive activities of humanity. This research explains the behavior of groundwater quality concerning arsenic speciation and its relationship with fluoride. The average total arsenic concentration of 19.95 µg/L and 20.29 µg/L is reported for the study period from 2015 to 2020, respectively, according to the Mexican standard. If the population drinks water directly, it is exposed to possible damage to health. The predominant arsenic species is As (V), with 95% and As (III) with 5%, this finding will allow us to define in greater detail the type of remediation that is required to reduce the content of this element in the water. Regarding the relationship between arsenic and fluorine, very small Pearson correlation coefficients of the order of 0.3241 and 0.3186 were found. The estimation of the space–time variation made it possible to identify the areas with the highest concentration of arsenic and fluorine, allowing the definition of the operating policies of these wells, thereby protecting the health of the inhabitants who consume this water.

Harnessing landfill gas (LFG) for electricity: A strategy to mitigate greenhouse gas (GHG) emissions in Jakarta (Indonesia)

Due to its increasing demands for fossil fuels, Indonesia needs an alternative energy to diversify its energy supply. Landfill gas (LFG), which key component is methane (CH₄), has become one of the most attractive options to sustain its continued economic development. This exploratory study seeks to demonstrate the added value of landfilled municipal solid waste (MSW) in generating sustainable energy, resulting from CH₄ emissions in the Bantargebang landfill (Jakarta). The power generation capacity of a waste-to-energy (WTE) plant based on a mathematical modeling was investigated. This article critically evaluated the production of electricity and potential income from its sale in the market. The project's environmental impact assessment and its socio-economic and environmental benefits in terms of quantitative and qualitative aspects were discussed. It was found that the emitted CH₄ from the landfill could be reduced by 25,000 Mt annually, while its electricity generation could reach one million kW ⋅h annually, savings on equivalent electricity charge worth US$ 112 million/year (based on US' 8/kW ⋅ h). An equivalent CO₂ mitigation of 3.4 × 10⁶ Mt/year was obtained. The income from its power sale were US$ 1.2 ×10⁶ in the 1^st year and 7.7 ×10⁷US$ in the 15^th year, respectively, based on the projected CH₄ and power generation. The modeling study on the Bantargebang landfill using the LFG extraction data indicated that the LFG production ranged from 0.05 to 0.40 m³ per kg of the landfilled MSW. The LFG could generate electricity as low as US' 8 per kW ⋅ h. With respect to the implications of this study, the revenue not only defrays the cost of landfill's operations and maintenance (O&M), but also provides an incentive and means to further improve its design and operations. Overall, this work not only leads to a diversification of primary energy, but also improves environmental protection and the living standard of the people surrounding the plant.