CuO-NiO binary transition metal oxide nanoparticle anchored on rGO nanosheets as high-performance electrocatalyst for the oxygen reduction reaction

Regulable in-situ autoredox for anchoring synergistic Ni/NiO nanoparticles on reduced graphene oxide with boosted alkaline electrocatalytic oxygen evolution

To develop ideal alternatives to noble metal catalysts, transition metal catalysts supported on graphene have been receiving extensive attention in the field of electrochemical energy. In this work, using graphene oxide (GO) and nickel formate as precursors, Ni/NiO synergistic nanoparticles with regulable composition are anchored on reduced graphene oxide (RGO) to prepare Ni/NiO/RGO composite electrocatalysts through in-situ autoredox. Thanks to the synergistic effect of Ni³⁺ active sites and Ni electron donors, the as-prepared Ni/NiO/RGO catalysts exhibit efficient electrocatalytic oxygen evolution performance in 1.0 M KOH electrolyte. The optimal sample has an overpotential of only 275 mV at a current density of 10 mA cm^-2 and a small Tafel slope of 90 mV dec^-1, which are very comparable to those of commercial RuO₂ catalyst. Additionally, the catalytic capacity and structure remain stable after 2000 cyclic voltammetry cycles. For the electrolytic cell assembled with the best-performing sample as anode and commercial Pt/C as cathode, the current density can reach 10 mA cm^-2 at a low potential of 1.57 V and remains stable after 30 h of continuous work. It would be expected that the as-developed Ni/NiO/RGO catalyst with high activity should have broad application prospects.

Enhanced charge carrier transfer process in nickel titanate nanostructures for environmental remediation of industrial dye

The effective charge carrier transfer process in one-dimensional (1D) NiTiO₃ nanofibers and NiTiO₃ nanoparticles was demonstrated experimentally, showcasing an effective photocatalytic enhancement under visible light ambience. The rhombohedral crystal structure of NiTiO₃ nanostructures was confirmed using X-ray diffractometer (XRD). The morphology and optical characteristics of the synthesized nanostructures were characterized using scanning electron microscopy (SEM) and UV-visible spectroscopy (UV-Vis). Nitrogen adsorption-desorption analysis corresponding to NiTiO₃ nanofibers showcased porous structures with an average pore size of ~3.9 nm. The photoelectrochemical (PEC) measurement studies revealed an enhanced photocurrent for the NiTiO₃ nanostructures, confirming enhanced charge carriers transportation in fibers than in particles due to the delocalized electrons in the conduction band, thereby hindering the photoexcited charge carrier's recombination. The photodegradation efficiency of methylene blue (MB) dye under the visible light irradiation revealed an enhancement in the rate of degradation for NiTiO₃ nanofibers when compared to NiTiO₃ nanoparticles.

Multifunctional Pt3Rh-Co3O4 alloy nanoparticles with Pt-enriched surface and induced synergistic effect for improved performance in ORR, OER, and HER

Engineering high-performance electrocatalysts to improve the kinetics of parallel electrochemical reactions in low-temperature fuel cells, water splitting, and metal-air battery applications is important and inevitable. In this study, by employing a chemical co-reduction method, we developed multifunctional Pt₃Rh-Co₃O₄ alloy with uniformly distributed ultrafine nanoparticles (2-3 nm), supported on carbon. The presence of Co₃O₄ and the incorporation of Rh led to a strong electronic and ligand effect in the Pt lattice environment, which caused the d-band center of Pt to shift. This shift improved the electrocatalytic performance of Pt₃Rh-Co₃O₄ alloy. When Pt₃Rh-Co₃O₄/C was used to catalyze the oxygen reduction reaction (E_1/2: 0.75 V), oxygen evolution reaction (η₁₀: 290 mV), and hydrogen evolution reaction (η₁₀: 55 mV), it showed greater endurance (mass activity loss of only 7%-17%) than Pt-Co₃O₄/C and Pt/C catalysts up to 5000 potential cycles in perchloric acid. Overall, the as-prepared Pt₃Rh-Co₃O₄/C showed high multifunctional electrocatalytic potency, as demonstrated by typical electrochemical studies, and its physicochemical properties endorse their extended performance for a wide range of energy storage and conversion applications.

Robust FeCoP nanoparticles grown on a rGO-coated Ni foam as an efficient oxygen evolution catalyst for excellent alkaline and seawater electrolysis

Electrochemical water splitting is a potential green hydrogen energy generation technique. With the shortage of fresh water, abundant seawater resources should be developed as the main raw material for water electrolysis. However, since the precipitation reaction of chloride ions in seawater will compete with the oxygen evolution reaction (OER) and corrode the catalyst, seawater electrolysis is restricted by the decrease in activity, low stability, and selectivity. Rational design and development of efficient and stable catalysts is the key to seawater electrolysis. Herein, a high-activity bimetallic phosphide FeCoP, grown on a reduced graphene oxide (rGO)-protected Ni Foam (NF) substrate using FeCo Prussian Blue Analogue (PBA) as a template, was designed for application in alkaline natural seawater electrolysis. The OER activity confirmed that the formed FeCoP@rGO/NF has high electrocatalytic performance. In 1 M KOH and natural alkaline seawater, the overpotential was only 257 mV and 282 mV under 200 mA cm^-2, respectively. It also demonstrated long-term stability up to 200 h. Therefore, this study provides new insight into the application of PBA as a precursor of bimetallic phosphide in the electrolysis of seawater at high current density.

Facile Synthesis of Low-Cost Copper-Silver and Cobalt-Silver Alloy Nanoparticles on Reduced Graphene Oxide as Efficient Electrocatalysts for Oxygen Reduction Reaction in Alkaline Media

Copper-silver and cobalt-silver alloy nanoparticles deposited on reduced graphene oxide (CuAg/rGO and CoAg/rGO) were synthesized and examined as electrocatalysts for oxygen reduction reaction (ORR) and hydrogen peroxide reduction reaction (HPRR) in alkaline media. Characterization of the prepared samples was done by transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray diffraction analysis (XRD), and scanning electron microscopy with integrated energy-dispersive X-ray spectroscopy (SEM-EDS). CuAg/rGO and CoAg/rGO nanoparticles diameter ranged from 0.4 to 9.2 nm. The Ag loading was ca. 40 wt.% for both electrocatalysts, with that for Cu and Co being 35 and 17 wt.%, respectively. CoAg/rGO electrocatalyst showed a Tafel slope of 109 mV dec⁻¹, significantly lower than that for CuAg/rGO (184 mV dec⁻¹), suggesting faster ORR kinetics. Additionally, a higher diffusion current density was obtained for CoAg/rGO (−2.63 mA cm⁻²) than for CuAg/rGO (−1.74 mA cm⁻²). The average value of the number of electrons transferred during ORR was 2.8 for CuAg/rGO and 3.3 for CoAg/rGO electrocatalyst, further confirming the higher ORR activity of the latter. On the other hand, CuAg/rGO showed higher peak current densities (−3.96 mA cm⁻²) for HPRR compared to those recorded for CoAg/rGO electrocatalyst (−1.96 mA cm⁻²).