Probing fundamental film parameters of immobilized enzymes--towards enhanced biosensor performance. Part I--QCM-D mass and rheological measurements

Bio-interfactants as double-sided tapes for graphene oxide

We present a versatile and highly substrate-independent approach for preparing multisandwich layers based on thermally reduced Graphene Oxide (rGO) which gets strongly attached by bio-interfactants using a layer-by-layer (LBL) aqueous dipping and rinsing process. The process allows for the deposition of homogeneous ultra-thin films (∼5.5 nm) in distinct surface topographies, thicknesses and compositions by varying the bio-interfactant layer(s). The layers formed on quartz or other semi conductive material are electrically conductive, flexible, and transparent. The here-developed approach could be applied for the fabrication of wearables, sensors, and antistatic transparent films.

Acoustic biosensors

Resonant and acoustic wave devices have been researched for several decades for application in the gravimetric sensing of a variety of biological and chemical analytes. These devices operate by coupling the measurand (e.g. analyte adsorption) as a modulation in the physical properties of the acoustic wave (e.g. resonant frequency, acoustic velocity, dissipation) that can then be correlated with the amount of adsorbed analyte. These devices can also be miniaturized with advantages in terms of cost, size and scalability, as well as potential additional features including integration with microfluidics and electronics, scaled sensitivities associated with smaller dimensions and higher operational frequencies, the ability to multiplex detection across arrays of hundreds of devices embedded in a single chip, increased throughput and the ability to interrogate a wider range of modes including within the same device. Additionally, device fabrication is often compatible with semiconductor volume batch manufacturing techniques enabling cost scalability and a high degree of precision and reproducibility in the manufacturing process. Integration with microfluidics handling also enables suitable sample pre-processing/separation/purification/amplification steps that could improve selectivity and the overall signal-to-noise ratio. Three device types are reviewed here: (i) bulk acoustic wave sensors, (ii) surface acoustic wave sensors, and (iii) micro/nano-electromechanical system (MEMS/NEMS) sensors.

Developing Biosensors in Developing Countries: South Africa as a Case Study

A mini-review of the reported biosensor research occurring in South Africa evidences a strong emphasis on electrochemical sensor research, guided by the opportunities this transduction platform holds for low-cost and robust sensing of numerous targets. Many of the reported publications centre on fundamental research into the signal transduction method, using model biorecognition elements, in line with international trends. Other research in this field is spread across several areas including: the application of nanotechnology; the identification and validation of biomarkers; development and testing of biorecognition agents (antibodies and aptamers) and design of electro-catalysts, most notably metallophthalocyanine. Biosensor targets commonly featured were pesticides and metals. Areas  of regional import to sub-Saharan Africa, such as HIV/AIDs and tuberculosis diagnosis, are also apparent in a review of the available literature. Irrespective of the targets, the challenge to the effective deployment of such sensors remains shaped by social and economic realities such that the requirements thereof are for low-cost and universally easy to operate devices for field settings. While it is difficult to disentangle the intertwined roles of national policy, grant funding availability and, certainly, of global trends in shaping areas of emphasis in research, most notable is the strong role that nanotechnology, and to a certain extent biotechnology, plays in research regarding biosensor construction. Stronger emphasis on collaboration between scientists in theoretical modelling, nanomaterials application and or relevant stakeholders in the specific field (e.g., food or health monitoring) and researchers in biosensor design may help evolve focused research efforts towards development and deployment of low-cost biosensors.

A sensitivity metric and software to guide the analysis of soft films measured by a quartz crystal microbalance

The TPM-sensitivity metric guides the analysis of viscoelastic thin films studied with a quartz crystal microbalance.

"Active surfaces" formed by immobilization of enzymes on solid-supported polymer membranes

In various domains ranging from catalysis to medical and environmental sciences, there is currently much focus on the design of surfaces that present active compounds at the interface with their environments. Here, we describe the design of "active surfaces" based on solid-supported monolayers of asymmetric triblock copolymers, which serve as templates for the attachment of enzymes. A group of poly(ethylene glycol)-block-poly(γ-methyl-ε-caprolactone)-block-poly[(2-dimethylamino) ethyl methacrylate] amphiphilic copolymers, with different hydrophilic and hydrophobic domains (PEG45-b-PMCLx-b-PDMAEMAy) was selected to generate solid-supported polymer membranes. The behavior of the copolymers in terms of their molecular arrangements at the air-water interface was established by a combination of Langmuir isotherms and Brewster angle microscopy. Uniform thin layers of copolymers were obtained by transferring films onto silica solid supports at optimal surface pressure. These solid-supported polymer membranes were characterized by assessing various properties, such as monolayer thickness, hydrophilic/hydrophobic balance, topography, and roughness. Laccase, used as an enzyme model, was successfully attached to copolymer membranes by stable interactions as followed by quartz crystal microbalance with dissipation measurements, and its activity was preserved, as indicated by activity assays. The interaction between the amphiphilic triblock copolymer films and immobilized enzymes represents a straightforward approach to engineer "active surfaces", with biomolecules playing the active role by their intrinsic bioactivity.

Anesthetics interacting with lipid rafts

The exact mechanism by which anesthetics induce cell membrane-mediated modifications is still an open question. Although the fluidization effect of the anesthetic molecules on the cellular membrane is widely recognized, it is not known if anesthetics show any preference for specific membrane domains, namely the lipid rafts. The importance of these membrane micro-domains derives from the fact that they have been associated with cell signaling pathways, as well as with specific drug interactions. The objective of this work is to contribute for the elucidation of this question through the comparison of the anesthetic interactions with membranes of various lipid compositions. Liposomes prepared with an equimolar mixture of POPC, sphingomyelin and cholesterol, were chosen as models for lipid rafts. The interactions of these liposomes with two local anesthetics, tetracaine and lidocaine, and one general anesthetic, propofol, were studied. The effect of cholesterol was investigated by comparing anesthetic interactions with POPC/SM liposomes and POPC/SM/CHOL liposomes. The following experimental techniques were used: quartz crystal microbalance with dissipation, differential scanning calorimetry and phosphorus nuclear magnetic resonance. Although the liposomes investigated by the different techniques are not in the same conditions, it is possible to assemble the information obtained from all experimental techniques employed to reach a general conclusion. Tetracaine interacts more with raftlike domains, lidocaine induces stronger modifications on POPC/SM liposomes and the results for propofol are not fully conclusive but it seems to be the least prone to lipid interactions. The results were compared with those obtained with DMPC-containing liposomes, reported in a previous work.