Characterisation of exopolymer R-202 isolated from Rhodococcus rhodochrous and its flocculating properties

Efficacy of exopolysaccharide in dye-laden wastewater treatment: A comprehensive review

The discharge of dye-laden wastewater into the water streams causes severe water and soil pollution, which poses a global threat to aquatic ecosystems and humans. A diverse array of microorganisms such as bacteria, fungi, and algae produce exopolysaccharides (EPS) of different compositions and exhibit great bioflocculation potency to sustainably eradicate dyes from water bodies. Nanomodified chemical composites of EPS enable their recyclability during dye-laden wastewater treatment. Nevertheless, the selection of potent EPS-producing strains and physiological parameters of microbial growth and the remediation process could influence the removal efficiency of EPS. This review will intrinsically discuss the fundamental importance of EPS from diverse microbial origins and their nanomodified chemical composites, the mechanisms in EPS-mediated bioremediation of dyes, and the parametric influences on EPS-mediated dye removal through sorption/bioflocculation. This review will pave the way for designing and adopting futuristic green and sustainable EPS-based bioremediation strategies for dye-laden wastewater in situ and ex situ.

Bioflocculation characteristics of bound extracellular polymers substances from Pseudomonas sp. XD-3 and behavior of polysaccharides

This study aimed to investigate the bioflocculation characteristics of bound extracellular polymers substances (B-EPS), which were extracted from Pseudomonas sp. XD-3. The flocculation efficiency of B-EPS achieved about 80%- 95% with an initial pH of 4-7, kaolin concentrations of 3-7 g L-1, temperature of 25-100 ℃ and B-EPS dosage of 9-105 mg L-1. The bioflocculation process of B-EPS conformed to pseudo-second-order kinetic mode, suggesting that the bioflocculation belonged to chemical adsorption process. Enzymatic hydrolysis experiments demonstrated that both polysaccharides and proteins were active components for bioflocculation. The polysaccharides were irregular aggregates with rough and porous surfaces and contained hydroxyl and carboxyl groups, which helped to promote bridging effect. Ribose, glucose and galactose were the main monosaccharides of polysaccharides. The molecular weight of the polysaccharides was relatively small, but the relatively loose configuration exposed more ion bridging sites, thus promoting the bioflocculation. Optimizing the ingredients of culture medium and culture time for B-EPS were effective strategies to increase the yield of flocculation active components. When the conditions were 10% of 2 g L-1 KH2PO4 + 5 g L-1 K2HPO4, 0.05% of Tween-80, citrate as carbon source and 32-48 h of culture time, both proteins and polysaccharides in B-EPS were significantly improved. This study gives an in-deep understanding on the flocculation characteristics of a novel bioflocculant from Pseudomonas sp. XD-3, which is conducive to the widespread application of bioflocculation.

Soluble Extracellular Polymeric Substances Produced by Parachlorella kessleri and Chlorella vulgaris: Biochemical Characterization and Assessment of Their Cadmium and Lead Sorption Abilities

In the present study, the potential of lead and cadmium removal by the extracellular polymeric substances (EPS) produced from Parachlorella kessleri and Chlorella vulgaris were investigated. Carbohydrates were the dominant components of EPS from both analyzed species. The contents of reducing sugars, uronic acids, and amino acids were higher in EPS synthesized by C. vulgaris than in EPS from P. kessleri. The analysis of the monosaccharide composition showed the presence of rhamnose, mannose and galactose in the EPS obtained from both species. The ICP-OES (inductively coupled plasma optical emission spectrometry) analyses demonstrated that C. vulgaris EPS showed higher sorption capacity in comparison to P. kessleri EPS. The sorption capacity of C. vulgaris EPS increased with the increase in the amount of metal ions. P. kessleri EPS had a maximum sorption capacity in the presence of 100 mg/L of metal ions. The FTIR analysis demonstrated that the carboxyl, hydroxyl, and carbonyl groups of EPS play a key role in the interactions with metal ions. The present study showed C. vulgaris EPS can be used as a biosorbent in bioremediation processes due to its biochemical composition, the presence of significant amounts of negatively charged uronic acids, and higher sorption capacity.

Optimal production of bioflocculant from Pseudomonas sp. GO2 and its removal characteristics of heavy metals

Bioflocculant may be a promising bioactivator for heavy metal removal duo to its eco-friendly properties and remarkable ability to adsorb heavy metals. In this study, bioflocculant production from a bacterium, Pseudomonas sp. GO2, was optimized and its removal efficiency for two heavy metal ions was evaluated. Results demonstrated that the maximal flocculation efficiency was achieved with concentration levels of 5 g/L glucose, 3 g/L casein, and 5 g/L NaCl, with an initial pH of 9.0, and a fermentation time of 48 h. Bioflocculant produced by GO2 had a stronger removal efficiency for Cd²⁺ than that of Pb²⁺, with highest removal efficiencies of 85.38% and 80.87%, respectively. The adsorption process was mainly dependent on the monolayer and chemisorption based on the adsorption isotherm and kinetic models. This study demonstrated that bioflocculant produced by the GO2 strain has the potential to be used in heavy metal treatment from industrial wastewater.

Physicochemical factors affecting flocculating properties of the proteoglycan isolated from Rhodococcus opacus

The water-soluble fraction of proteoglycan RS-89 isolated from the Rhodococcus opacus FCL89 and composed of 64.6% polysaccharide and 9.44% protein has been studied as regards its flocculating activity. The RS-89 polysaccharide component includes mannose, galactose and glucose at the molar ratio of 2.7: 1.3: 1. The basic factors affecting flocculating activity of the RS-89 have been established. Additionally, the kinetics of kaolin sedimentation without and with the bioflocculant was investigated. The presence of divalent metal ions had a positive effect on the flocculating activity of the RS-89. The addition of Ca2+ increased the RS-89 flocculating activity in comparison to the other studied metals. It was proved that the proteoglycan RS-89 achieved the highest flocculating activity at the concentration equal to 2 mg/L and in the presence of 10 mmol/L of Ca2+. The zeta potential values are less negative when there is an interaction between the kaolin particles and metal ions without the RS-89 in the tested systems. Therefore, the proposed mechanism to describe the proteoglycan interaction with kaolin particles in the presence of divalent ions includes charge neutralization and a bridging mechanism.

Extracellular Polymeric Substances (EPS) as Microalgal Bioproducts: A Review of Factors Affecting EPS Synthesis and Application in Flocculation Processes

Microalgae are natural resources of intracellular compounds with a wide spectrum of applications in, e.g., the food industry, pharmacy, and biofuel production. The extracellular polymeric substances (EPS) released by microalgal cells are a valuable bioproduct. Polysaccharides, protein, lipids, and DNA are the main constituents of EPS. This review presents the recent advances in the field of the determinants of the synthesis of extracellular polymeric substances by microalgal cells and the EPS structure. Physical and chemical culture conditions have been analyzed to achieve useful insights into the development of a strategy optimizing EPS production by microalgal cells. The application of microalgal EPS for flocculation and mechanisms involved in this process are also discussed in terms of biomass harvesting. Additionally, the ability of EPS to remove toxic heavy metals has been analyzed. With their flocculation and sorption properties, microalgal EPS are a promising bioproduct that can potentially be used in harvesting algal biomass and wastewater management.

Subtopic: Advances in water and wastewater treatment harvesting of Chlorella sp. microalgae using Aspergillus niger as bio-flocculant for aquaculture wastewater treatment

Microalgae have been increasingly used to generate biofuel, thus a sustainable technique should be implemented to harvest the biomass to ensure its existence in the environment. Aspergillus niger was used as bio-flocculant to harvest microalgae from aquaculture wastewater via flocculation technique over a range of pH and mixing rate. The bio-flocculant showed ability to adapt at a wide range of pH from 3.0 to 9.0 and at a mixing rate of 100-150 rpm, producing a harvesting efficiency of higher than 90%. The treated water possessed low concentration of chlorophyll-a (0.3-0.6 mg L^-1) and cell density (2 × 10⁶-3 × 10⁶ cell mL^-1). These indicate that Aspergillus niger is a promising bio-flocculant to be used in harvesting microalgae, thus promoting the use of flocculation as a green technology in aquaculture wastewater treatment.

Removal of Pollutants in Mine Wastewater by a Non-Cytotoxic Polymeric Bioflocculant from Alcaligenes faecalis HCB2

Bioflocculation is a physicochemical technique often employed to efficiently remove colloidal water pollutants. Consequently, in this study, a bioflocculant was produced, characterised and applied to remove pollutants in mine wastewater. The maximum flocculation activity of 92% was recorded at 30 °C, pH 9.0 when maltose and urea were used as energy sources and 72 h of fermentation at the inoculum size of 1% (v/v). K⁺ proved to be a favourable cation. The bioflocculant yield of 4 g/L was obtained. Scanning electron microscopy illustrated a hexagonal-like structure of the bioflocculant. It is composed of carbohydrates and proteins in mass proportion of 88.6 and 9.5%, respectively. The Fourier transform infrared spectrum revealed the presence of hydroxyl, amide and amino functional groups. More than 73% of the bioflocculant was obtained after exposure to 600 °C using the thermogravimetric analyser. Human embryonic kidney 293 (HEK 293) cells exhibited 95% viability after being treated with 200 µg/µL of the bioflocculant. The flocculation mechanisms were proposed to be as a result of a double layer compression by K⁺, chemical reactions and bridging mechanism. The removal efficiencies of 59, 72, and 75% on biological oxygen demand, chemical oxygen demand and sulphur, were obtained respectively. Thus, the bioflocculant have potential use in wastewater treatment.

Nano-Montmorillonite Regulated Crystallization of Hierarchical Strontium Carbonate in a Microbial Mineralization System

In this paper, nano-montmorillonite (nano-MMT) was introduced into the microbial mineralization system of strontium carbonate (SrCO₃). By changing the nano-MMT concentration and the mineralization time, the mechanism of mineralization was studied. SrCO₃ superstructures with complex forms were acquired in the presence of nano-MMT as a crystal growth regulator. At low concentrations of nano-MMT, a cross-shaped SrCO₃ superstructure was obtained. As the concentration increased, flower-like SrCO₃ crystals formed via the dissolution and recrystallization processes. An emerging self-assembly process and crystal polymerization mechanism have been proposed by forming complex flower-like SrCO₃ superstructures in high concentrations of nano-MMT. The above research indicated that unique bionic synthesis strategies in microbial systems could not only provide a useful route for the production of inorganic or inorganic/organic composites with a novel morphology and unique structure but also provide new ideas for the treatment of radionuclides.

Flocculation behaviour of bioflocculant produced from chicken viscera

The flocculation performance of bioflocculant produced by Aspergillus flavus S44-1 grown on chicken viscera hydrolysate was investigated. The investigations were carried out using jar testing and kaolin clay suspension as model wastewater. The bioflocculant yielded a minimum of 83.1% efficiency in flocculating 2-12 g L-1 kaolin clay suspension over a wide temperature range (4-80 °C) and functioned maximally at neutral pH. The bioflocculant significantly flocculated different suspended particles such as activated carbon (92%), soil solid (94.8%), and algae (69.4%) at varying concentrations. Bridging mediated by cation is suggested as the main mechanism of flocculation by the present bioflocculant.

Microbial Flocculants as an Alternative to Synthetic Polymers for Wastewater Treatment: A Review

Microorganisms such as bacteria, fungi, and microalgae have been used to produce bioflocculants with various structures. These polymers are active substances that are biodegradable, environmentally harmless, and have flocculation characteristics. Most of the developed microbial bioflocculants displayed significant flocculating activity (FA > 70–90%) depending on the strain used and on the operating parameters. These biopolymers have been investigated and successfully used for wastewater depollution in the laboratory. In various cases, selected efficient microbial flocculants could reduce significantly suspended solids (SS), turbidity, chemical oxygen demand (COD), total nitrogen (Nt), dye, and heavy metals, with removal percentages exceeding 90% depending on the bioflocculating materials and on the wastewater characteristics. Moreover, bioflocculants showed acceptable results for sludge conditioning (accepted levels of dry solids, specific resistance to filtration, moisture, etc.) compared to chemicals. This paper explores various bioflocculants produced by numerous microbial strains. Their production procedures and flocculating performance will be included. Furthermore, their efficiency in the depollution of wastewater will be discussed.

Production and Characterization of a Bioflocculant Produced by Bacillus salmalaya 139SI-7 and Its Applications in Wastewater Treatment

The production, optimization, and characterization of the bioflocculant QZ-7 synthesized by a novel Bacillus salmalaya strain 139SI isolated from a private farm soil in Selangor, Malaysia, are reported. The flocculating activity of bioflocculant QZ-7 present in the selected strain was found to be 83.3%. The optimal culture for flocculant production was achieved after cultivation at 35.5 °C for 72 h at pH 7 ± 0.2, with an inoculum size of 5% (v/v) and sucrose and yeast extract as carbon and nitrogen sources. The maximum flocculating activity was found to be 92.6%. Chemical analysis revealed that the pure bioflocculant consisted of 79.08% carbohydrates and 15.4% proteins. The average molecular weight of the bioflocculant was calculated to be 5.13 × 10⁵ Da. Infrared spectrometric analysis showed the presence of carboxyl (COO-), hydroxyl (-OH), and amino (-NH₂) groups, polysaccharides and proteins. The bioflocculant QZ-7 exhibited a wide pH stability range from 4 to 7, with a flocculation activity of 85% at pH 7 ± 0.2. In addition, QZ-7 was thermally stable and retained more than 80% of its flocculating activity after being heated at 80 °C for 30 min. SEM analysis revealed that QZ-7 exhibited a clear crystalline brick-shaped structure. After treating wastewater, the bioflocculant QZ-7 showed significant flocculation performance with a COD removal efficiency of 93%, whereas a BOD removal efficiency of 92.4% was observed in the B. salmalaya strain 139SI. These values indicate the promising applications of the bioflocculant QZ-7 in wastewater treatment.

Production and flocculating properties of a compound biopolymer flocculant from corn ethanol wastewater

A compound biopolymer flocculant (CBF) produced using corn ethanol wastewater as substrate was investigated. After optimization of culture conditions, 3.08 g/L of purified CBF was extracted from the culture broth following 48 h of cultivation. The CBF macromolecule is mainly composed of protein (15.9%) and polysaccharide (81.8%). The polysaccharide component includes neutral sugars (28.92%), amino sugars (4.04%) and uronic acid (11.69%), with the neutral sugars being glucose, mannose, and lactose at a molar ratio of 4.1:1.5:1.9. CBF is pH tolerant from 3.0 to 12.0 and thermal tolerant from 20 to 100 °C, allowing for its application over a wide range of conditions. Furthermore, the Langmuir model better describes CBF adsorption on kaolin clay, as compared to the Freundlich model. Charge neutralization and bridging mechanisms are the primary flocculation mechanisms. In addition, CBF shows a high methylene blue removal efficiency. These results indicate that this compound biopolymer flocculant has great potential in dye wastewater treatment.