Chitosan adsorbent reinforced with citric acid modified β-cyclodextrin for highly efficient removal of dyes from reactive dyeing effluents

Graphene oxide-chitosan coated PVDF adsorptive microfiltration membrane: Enhancing dye removal and antifouling properties

This study investigates graphene oxide (GO) modified poly(vinylidene fluoride) (PVDF) membranes focusing on their dye rejection efficiency and their antifouling properties against bovine serum albumin (BSA). These membranes were prepared by modifying commercial PVDF membrane with a thin layer of GO nanosheets and chitosan (CS) using vacuum filtration. The synergistic physicochemical properties of the GO-CS/PVDF membranes were analyzed by XRD, FTIR, Raman, and XPS spectroscopy. The surface morphologies were observed by SEM and AFM microscopy, and WCA measurements. The deposition of GO and CS in the presence of citric acid resulted in a decrease in pore size and an increase in hydrophilicity. Modified membranes showed enhanced rejection of RB and MB, with rates increasing from 13.0 to 96.0 % and 28.3 to 69.1 %, respectively. Antifouling studies using BSA on selected membranes outperformed pristine membranes, which had higher irreversible fouling due to pore blockage. GO-CS/PVDF membranes exhibited higher flux recovery and lower irreversible fouling due to increased hydrophilicity, which prevents tight cake layer formation. Minimal detachment of the GO-CS layer during the long-term stability test is confirmed by minor fluctuations in dye flux and rejection. In summary, enhancing PVDF membranes with GO and CS augments dye rejection rates and bolsters antifouling properties.

Novel amino-ethyl carboxymethyl cellulose crosslinked ampholyte hydrogel development for Methyl orange removal from waste water

In the modern era, with the rapid growth of various industries, the issues of energy crisis and environmental pollution have garnered increasing attention. One significant source of industrial pollution is printing and dyeing wastewater. This wastewater often contains dyes that have aromatic structures and azo groups, such as Methyl orange (MO), which are both toxic and difficult to degrade. If these dyes are released into the wastewater stream without any treatment, they can have adverse effects on ecological balance and human health. Therefore, it is crucial to identify suitable treatment strategies to efficiently remove dyes from wastewater systems before discharge. In this study, the Methyl orange (MO) azo dye has been removed from dyes-contaminated wastewater, for the first time, using a novel amino-ethyl carboxymethyl cellulose crosslinked ampholyte hydrogel (AECMC). Different characterization methods, including FTIR, TGA, and DSC were used to characterize the generated AECMC compounds. The water absorption and cationic exchange capacities were assessed. Factors affecting the MO anions adsorption including MO concentration, adsorption pH, temperature, time, adsorbent dose, and agitation speed have been investigated. Moreover, the kinetics of the adsorption process was assessed by the use of three models: pseudo-first-order, Pseudo-second-order, and Elovich. Moreover, the mechanism of the adsorption process was monitored using the Intraparticle diffusion and Boyd models. Additionally, the adsorption isotherm was examined using established models such as Langmuir, Freundlich, and Temkin isotherms. The thermodynamic characteristics of the MO adsorption process have been investigated at various adsorption temperatures using the Van't Hoff model. The results obtained from the study indicate that the process of MO adsorption adhered to the Pseudo-second-order kinetic model, the Langmuir isotherm model was found to be applicable, and spontaneous and exhibited an endothermic character. In conclusion, the developed novel amino-ethyl carboxymethyl cellulose crosslinked ampholyte hydrogels (AECMC) have successive in the removal of the MO anionic dye from contaminated wastewater.

Recent advances in chitosan-based nanocomposites for adsorption and removal of heavy metal ions

Due to the high concentration of various toxic and dangerous pollutants, industrial effluents have imposed increasing threats. Among the various processes for wastewater treatment, adsorption is widely used due to its simplicity, good treatment efficiency, availability of a wide range of adsorbents, and cost-effectiveness. Chitosan (CS) has received great attention as a pollutant adsorbent due to its low cost and many -OH and -NH2 functional groups that can bind heavy metal ions. However, weaknesses such as sensitivity to pH, low thermal stability and low mechanical strength, limit the application of CS in wastewater treatment. The modification of these functional groups can improve its performance via cross-linking and grafting agents. The porosity and specific surface area of CS in powder form are not ideal, so physical modification of CS via integration with other materials (e.g., metal oxide, zeolite, clay, etc.) leads to the creation of composite materials with improved absorption performance. This review provides reports on the application of CS and its nanocomposites (NCs) for the removal of various heavy metal ions. Synthesis strategy, adsorption mechanism and influencing factors on sorbents for heavy metals are discussed in detail.

β-cyclodextrin polymer composites for the removal of pharmaceutical substances, endocrine disruptor chemicals, and dyes from aqueous solution- A review of recent trends

Cyclodextrin (CD) and its derivatives are receiving attention as a new-generation adsorbent for water pollution treatment due to their external hydrophilic and internal hydrophobic properties. Among types of CD, β-Cyclodextrin (βCD) has been a material of choice with a proven track record for a range of utilities in distinct domains, owing to its unique cage-like structural conformations and inclusion complex-forming ability, especially to mitigate emerging contaminants (ECs). This article outlines βCD composites in developing approaches of their melds and composites for purposes such as membranes for removal of the ECs in aqueous setups have been explored with emphasis on recent trends. Electrospinning has bestowed an entirely different viewpoint on polymeric materials, comprising βCD, in the framework of diverse functions across a multitude of niches. Besides, this article especially discusses βCD polymer composite membrane-based removal of contaminants such as pharmaceutical substances, endocrine disruptors chemicals, and dyes. Finally, in this article, the challenges and future directions of βCD-based adsorbents are discussed, which may shed light on pragmatic commercial applications of βCD polymer composite membranes.

Citric acid cross-linked β-cyclodextrins: A review of preparation and environmental/biomedical application

The β-cyclodextrins (β-CD) are biocompatible macrocyclic candidates for the preparation of various composites with enhanced functions. While nontoxic and biodegradable citric acid (CA) is the favorite crosslinking agent for fabricating hierarchical advanced structures. The carboxyl and hydroxyl groups on CA can serve as "structural bridges" and enhance the solubility of β-CD. Leading to the construction of CA cross-linked β-CD with marvelous complicated structures and targeted functions. Here, we directly categorized the grafted composite materials into two main types such as organic and inorganic materials. Particularly, some representative composite materials are listed and analyzed in detail according to their preparation, advantages of unique characteristics, as well as the possible applications in environmental and biomedical fields such as adsorption of pollutants, sensors, and biomedical applications.

Insights into Recent Advances of Biomaterials Based on Microbial Biomass and Natural Polymers for Sustainable Removal of Pharmaceuticals Residues

Pharmaceuticals are acknowledged as emerging contaminants in water resources. The concentration of pharmaceutical compounds in the environment has increased due to the rapid development of the pharmaceutical industry, the increasing use of human and veterinary drugs, and the ineffectiveness of conventional technologies to remove pharmaceutical compounds from water. The application of biomaterials derived from renewable resources in emerging pollutant removal techniques constitutes a new research direction in the field. In this context, the article reviews the literature on pharmaceutical removal from water sources using microbial biomass and natural polymers in biosorption or biodegradation processes. Microorganisms, in their active or inactive form, natural polymers and biocomposites based on inorganic materials, as well as microbial biomass immobilized or encapsulated in polymer matrix, were analyzed in this work. The review examines the benefits, limitations, and drawbacks of employing these biomaterials, as well as the prospects for future research and industrial implementation. From these points of view, current trends in the field are clearly reviewed. Finally, this study demonstrated how biocomposites made of natural polymers and microbial biomass suggest a viable adsorbent biomaterial for reducing environmental pollution that is also efficient, inexpensive, and sustainable.

A Comprehensive Review of Polysaccharide-Based Hydrogels as Promising Biomaterials

Polysaccharides have emerged as a promising material for hydrogel preparation due to their biocompatibility, biodegradability, and low cost. This review focuses on polysaccharide-based hydrogels' synthesis, characterization, and applications. The various synthetic methods used to prepare polysaccharide-based hydrogels are discussed. The characterization techniques are also highlighted to evaluate the physical and chemical properties of polysaccharide-based hydrogels. Finally, the applications of SAPs in various fields are discussed, along with their potential benefits and limitations. Due to environmental concerns, this review shows a growing interest in developing bio-sourced hydrogels made from natural materials such as polysaccharides. SAPs have many beneficial properties, including good mechanical and morphological properties, thermal stability, biocompatibility, biodegradability, non-toxicity, abundance, economic viability, and good swelling ability. However, some challenges remain to be overcome, such as limiting the formulation complexity of some SAPs and establishing a general protocol for calculating their water absorption and retention capacity. Furthermore, the development of SAPs requires a multidisciplinary approach and research should focus on improving their synthesis, modification, and characterization as well as exploring their potential applications. Biocompatibility, biodegradation, and the regulatory approval pathway of SAPs should be carefully evaluated to ensure their safety and efficacy.

Adsorption of heavy metal onto biomass-derived activated carbon: review

Due to the rapid development of the social economy and the massive increase in population, human beings continue to undertake processing, and commercial manufacturing activities of heavy metals, which has caused serious damage to the environment and human health. Heavy metals lead to serious environmental problems such as soil contamination and water pollution. Human health and the living environment are closely affected by the handling of heavy metals. Researchers must find several simple, economical and practical methods to adsorb heavy metals. Adsorption technology has been recognized as an efficient and economic strategy, exhibiting the advantages of recovering and reusing adsorbents. Biomass-derived activated carbon adsorbents offer large adjustable specific surface area, hierarchically porous structure, strong adsorption capacity, and excellent high economic applicability. This paper focuses on reviewing the preparation methods of biomass-derived activated carbon in the past five years. The application of representative biomass-derived activated carbon in the adsorption of heavy metals preferentially was described to optimize the critical parameters of the activation type of samples and process conditions. The key factors of the adsorbent, the physicochemical properties of the heavy metals, and the adsorption conditions affecting the adsorption of heavy metals are highlighted. In addition, the challenges faced by biomass-derived activated carbon are also discussed.

Cotton Cord Coated with Cyclodextrin Polymers for Paraquat Removal from Water

The contamination of hazardous agrochemical substances in water caused essential trouble for humans and the environment. The functional textile was used as an effective adsorbent for paraquat removal from an aqueous solution. The coating of anionic cyclodextrin polymer, issued from the cross-linking between 1,2,3,4-butanetetracarboxylic acid and β−cyclodextrin in the presence of poly (vinyl alcohol), on the cotton cord, was firstly investigated. Their physicochemical characteristics were also characterized by gravimetry, acid–base titration, ATR-FTIR, ¹³C NMR, TGA, and stereo-microscopy. The BDP5 system revealed 107.3% coating yield, 1.13 mmol/g COOH groups, and 95.1% paraquat removal for 25 mg/L of initial concentration. The pseudo-second-order model was appropriate for kinetics using 6 h of contact time. Langmuir isotherm was suitable with the maximum adsorption of 30.3 mg/g for paraquat adsorption. The weight loss was 10.7% and 7.8%, respectively, for water and 5% v/v of HCI in ethanol after 120 h of contact time. Finally, the reusability efficiency stayed at 88.9% after five regeneration.

Some Well-Known Alginate and Chitosan Modifications Used in Adsorption: A Review

Owing to environmental pollution and increasingly strict regulations, heavy metals have attracted the attention of many researchers in various disciplines. Alginate and chitosan derivatives have gained popularity as biosorbents for water treatment. An increase in the number of publications on modified biosorbents for the biosorption of toxic compounds reveals widespread interest in examining the requirements and positive contribution of each modification type. This paper reviews the advantages and disadvantages of using alginate and chitosan for adsorption. Well-known modifications based on chitosan and alginate, namely, grafting, functionalization, copolymerization and cross-linking, as well as applications in the field of adsorption processes, especially amino acid functionalization, are reviewed. The selection criteria for the best biosorbents and their effectiveness and proposed mechanism of adsorption are discussed critically. In the conclusion, the question of why these adsorbents need modification before use is addressed.

Adsorption of Cationic Contaminants by Cyclodextrin Nanosponges Cross-Linked with 1,2,3,4-Butanetetracarboxylic Acid and Poly(vinyl alcohol)

Cationic organic pollutants (dyes and pesticides) are mainly hydrosoluble and easily contaminate water and create a serious problem for biotic and abiotic species. The elimination of these dangerous contaminants from water was accomplished by adsorption using cyclodextrin nanosponges. These nanosponges were elaborated by the cross-linking between 1,2,3,4-butanetetracarboxylic acid and β-cyclodextrin in the presence of poly(vinyl alcohol). Their physicochemical characteristics were characterized by gravimetry, acid-base titration, TGA, 13C NMR, ATR-FTIR, Raman, X-ray diffraction, and Stereomicroscopy. The BP5 nanosponges displayed 68.4% yield, 3.31 mmol/g COOH groups, 0.16 mmol/g β-CD content, 54.2% swelling, 97.0% PQ removal, 96.7% SO removal, and 98.3% MG removal for 25 mg/L of initial concentration. The pseudo-second-order model was suitable for kinetics using 180 min of contact time. Langmuir isotherm was suitable for isotherm with the maximum adsorption of 120.5, 92.6, and 64.9 mg/g for paraquat (PQ), safranin (SO), and malachite green (MG) adsorption, respectively. Finally, the reusability performance after five regeneration times reached 94.1%, 91.6%, and 94.6% for PQ, SO, and MG adsorption, respectively.

Cyclodextrin polymer-confined urease for the fast and efficient removal of urea

A highly efficient urease immobilized material was synthesized for fast and efficient urea removal with high pH and temperature tolerance.

Modification of cyclodextrin and use in environmental applications

Water pollution, which has become a global problem in parallel with environmental pollution, is a problem that needs to be solved urgently, considering the gradual depletion of water resources. The inadequacy of the water treatment methods and the materials used somehow directed the researchers to look for dual character structures such as biocompatible and biodegradable β-cyclodextrin (β-CD). β-CD, which is normally insoluble in water, is used in demanding wastewater applications by being modified with the help of different agents to be water soluble or transformed into polymeric adsorbents as a result of co-polymerization via cross-linkers. In this way, in addition to the host-guest interactions offered by β-CD, secondary forces arising from these interactions provide advantages in terms of regeneration and reusability. However, the adsorption efficiency and synthesis steps need to be improved. Based on the current studies presented in this review, in which cross-linkers and modification methods are also mentioned, suggestions for novel synthesis methods of new-generation β-CD-based materials, criticisms, and recent methods of removal of micropollutants such as heavy metals, industrial dyes, harmful biomolecules, and pharmaceutics wastes are mentioned.

Sequestration of Hazardous Dyes from Aqueous Solution Using Raw and Modified Agricultural Waste

The continuous degradation of surface water quality by dye materials is of concern globally. Agricultural waste Litchi chinensis (LC) peel in its raw (RL) and modified (CL) forms was used as potential sorbents for sequestration of Congo red (CR) dye from an aqueous solution. The sorbents were characterized before and after sorption with Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), Brunauer, Emmett, and Teller (BET) surface area analysis, and X-ray diffraction (XRD). Determination of the point of zero charge (PZC) suggested CR dye sorption from an aqueous solution would be best in acidic pH. Batch experimental drivers such as the effects of time, dosage, initial concentration, pH, and temperature were optimized and used. Results from the study showed that modification with citric acid (CA) reduced the equilibration time from 90 to 15 min. Change in water chemistry did not significantly affect the removal efficiency of the sorbent but rather slightly improved it for both sorbent types. The smaller particle size of <125 μm recorded higher removal efficiency than the larger one (>125 μm). The effect of temperature affects the sorption differently. For the RL system, it decreases with an increase in the temperature, while for the CL system it increases with an increase in temperature. The Langmuir isotherm best described the equilibrium data obtained based on the linearized coefficients with maximum sorption capacities ( $q_{\max }$ ) of 55.56 mg/g (RL) and 58.48 mg/g (CL). The pseudo-second-order model also best described the kinetic data. The thermodynamics study showed that the reaction is both feasible and spontaneous. Both sorbents recorded high removal efficiency for other dyes such as rhodamine B, methylene blue, methyl orange, malachite green, and erythrosin B. The five cycled regeneration/sorption experiments with 0.1 M NaOH as the desorbing agent showed that the regenerated sorbents efficiently removed CR dye from an aqueous solution close to their virgin samples for the first three cycles. This research, therefore, establishes LC peel as a potential eco-friendly, readily available, and effective sorbent for sequestration of hazardous dyes from wastewater.

A decade development in the application of chitosan-based materials for dye adsorption: A short review

The presence of dyes in the aquatic environment as a result of anthropogenic activities, especially textile industries, is a critical environmental challenge that hinders the availability of potable water. Different wastewater treatment approaches have been used to remediate dyes in aquatic environments; however, most of these approaches are limited by factors ranging from high cost to the incomplete removal of the dyes and contaminants. Thus, the use of adsorption as a water treatment technology to remove dyes and other contaminants has been widely investigated using different adsorbents. This study evaluated the significance of chitosan as a viable adsorbent for removing dyes from water treatment. We summarised the literature and research results obtained between 2009 and 2020 regarding the adsorption of dyes onto chitosan and modified chitosan-based adsorbents prepared through physical and chemical processing, including crosslinking impregnation, grafting, and membrane preparation. Furthermore, we demonstrated the effects of various chitosan-based materials and modifications; they all improve the properties of chitosan by promoting the adsorption of dyes. Hence, the application of chitosan-based materials with various modifications should be considered a cutting-edge approach for the remediation of dyes and other contaminants in aquatic environments toward the global aim of making potable water globally available.

Adsorption of Paraquat by Poly(Vinyl Alcohol)-Cyclodextrin Nanosponges

The contamination of hydrosoluble pesticides in water could generate a serious problem for biotic and abiotic components. The removal of a hazardous agrochemical (paraquat) from water was achieved by adsorption processes using poly(vinyl alcohol)-cyclodextrin nanosponges, which were prepared with various formulations via the crosslinking between citric acid and β-cyclodextrin in the presence of poly(vinyl alcohol). The physicochemical properties of nanosponges were also characterized by different techniques, such as gravimetry, thermogravimetry, microscopy (SEM and Stereo), spectroscopy (UV-visible, NMR, ATR-FTIR, and Raman), acid-base titration, BET surface area analysis, X-ray diffraction, and ion exchange capacity. The C10D-P2 nanosponges displayed 60.2% yield, 3.14 mmol/g COOH groups, 0.335 mmol/g β-CD content, 96.4% swelling, 94.5% paraquat removal, 0.1766 m2 g-1 specific surface area, and 5.2 × 10-4 cm3 g-1 pore volume. The presence of particular peaks referring to specific functional groups on spectroscopic spectra confirmed the successful polycondensation on the reticulated nanosponges. The pseudo second-order model (with R2 = 0.9998) and Langmuir isotherm (with R2 = 0.9979) was suitable for kinetics and isotherm using 180 min of contact time and a pH of 6.5. The maximum adsorption capacity was calculated at 112.2 mg/g. Finally, the recyclability of these nanosponges was 90.3% of paraquat removal after five regeneration times.

Chitosan-based hybrid materials for adsorptive removal of dyes and underlying interaction mechanisms

Environmental pollution by dyes molecules has become a subject of intensive research in recent years due to their hazardous effects on human health, organisms, and animals. Effective treatment and removal of dye molecules from the environmental matrices and water sources are of supreme concern. The deployment of cheap, safe, green, sustainable, and eco-friendly materials to remove these pollutants from water is the main challenge during the last decades. Chitosan and its derivatives/composites, as a cheap, easily available, and environmentally friendly sorbent, have attracted increasing attention for the removal of dye molecules. This review article focuses on the application of chitosan and chitosan-based smart adsorbents for the removal of dyes. Recent methods for the preparation of chitosan-based composites and their application in the removal of dyes are discussed. Moreover, the possible mechanisms for the interaction of chitosan and chitosan-based adsorbents with dyes molecules were evaluated. Finally, future prospects of using chitosan as an adsorbent for the removal of dye molecules are directed.

Adsorption of reactive blue 49 onto cross-linked chitosan-based composites containing waste mussel shell and waste active sludge char

Cross-linked chitosan/waste mussel shell (C/WMS) and chitosan/waste mussel shell/waste active sludge char (C/WMS/WASC) composites were prepared from waste mussel shell, waste active sludge (WAS), and chitosan, and cross-linked with glutaraldehyde. The quantities of chitosan, WMS, and WASC used for the C/WMS and C/WMS/WASC composites were 1:1 and 1:0.5:0.5, respectively. The two adsorbents were characterized for their quality by a scanning electron microscope (SEM), an energy-dispersive X-ray spectroscopy (EDX), and a Brunauer, Emmett and Teller (BET) analyzer. The effects of contact time (0-1,620 mins), pH (1-5), adsorbent dosage (0.01-0.1 g/50 ml), initial dye concentration (20-100 mg/L), and temperature (25-45 °C) on Reactive Blue 49 (RB49) adsorption onto C/WMS and C/WMS/WASC composites were investigated. The maximum RB49 adsorption capacity of C/WMS and C/WMS/WASC composites was 54.7 and 38.8 mg/g, respectively. The experimental data were analyzed by kinetic and isotherm models. The Freundlich isotherm was a good fit for the experimental data of RB49 adsorption on C/WMS and C/WMS/WASC composites, and the adsorption kinetics for both adsorbents were the pseudo-second-order rate equation. All results showed the preparative adsorbents can be used as effective adsorbents for the treatment of waste water contaminated with RB49 since they are low cost and eco-friendly for the environment.

Cyclodextrin Polymers and Cyclodextrin-Containing Polysaccharides for Water Remediation

Chemical pollution of water has raised great concerns among citizens, lawmakers, and nearly all manufacturing industries. As the legislation addressing liquid effluents becomes more stringent, water companies are increasingly scrutinized for their environmental performance. In this context, emergent contaminants represent a major challenge, and the remediation of water bodies and wastewater demands alternative sorbent materials. One of the most promising adsorbing materials for micropolluted water environments involves cyclodextrin (CD) polymers and cyclodextrin-containing polysaccharides. Although cyclodextrins are water-soluble and, thus, unusable as adsorbents in aqueous media, they can be feasibly polymerized by using different crosslinkers such as epichlorohydrin, polycarboxylic acids, and glutaraldehyde. Likewise, with those coupling agents or after substituting hydroxyl groups with more reactive moieties, cyclodextrin units can be covalently attached to a pre-existing polysaccharide. In this direction, the functionalization of chitosan, cellulose, carboxymethyl cellulose, and other carbohydrate polymers with CDs is vastly found in the literature. For the system containing CDs to be used for remediation purposes, there are benefits from a synergy that arises from (i) the ability of CD units to interact selectively with a broad spectrum of molecules, forming inclusion complexes and higher-order supramolecular assemblies, (ii) the functional groups of the crosslinker comonomers, (iii) the three-dimensional structure of the crosslinked network, and/or (iv) the intrinsic characteristics of the polysaccharide backbone. In view of the most recent contributions regarding CD-based copolymers and CD-containing polysaccharides, this review discusses their performance as adsorbents in micropolluted water environments, as well as their interaction patterns, addressing the influence of their structural and physicochemical properties and their functionalization.

The Role of β-Cyclodextrin in the Textile Industry-Review

β-Cyclodextrin (β-CD) is an oligosaccharide composed of seven units of D-(+)-glucopyranose joined by α-1,4 bonds, which is obtained from starch. Its singular trunk conical shape organization, with a well-defined cavity, provides an adequate environment for several types of molecules to be included. Complexation changes the properties of the guest molecules and can increase their stability and bioavailability, protecting against degradation, and reducing their volatility. Thanks to its versatility, biocompatibility, and biodegradability, β-CD is widespread in many research and industrial applications. In this review, we summarize the role of β-CD and its derivatives in the textile industry. First, we present some general physicochemical characteristics, followed by its application in the areas of dyeing, finishing, and wastewater treatment. The review covers the role of β-CD as an auxiliary agent in dyeing, and as a matrix for dye adsorption until chemical modifications are applied as a finishing agent. Finally, new perspectives about its use in textiles, such as in smart materials for microbial control, are presented.

Efficient removal of crystal violet dye using EDTA/graphene oxide functionalized corncob: a novel low cost adsorbent

In this study, EDTA functionalized corncob (EDTA-corncob) and EDTA/graphene oxide functionalized corncob (EDTA-GO/corncob) were prepared using disodium ethylenediamine tetraacetic acid and the graphene oxide immersion method. EDTA-corncob and EDTA-GO/corncob were characterized by SEM and FTIR spectroscopy. On this basis, the adsorption properties of EDTA-corncob and EDTA-GO/corncob were studied with crystal violet as the adsorbate. The optimum adsorption conditions were determined by the effect of samples on the adsorption properties of crystal violet at different times, temperatures and pH, and the reusability of the samples was studied. The results showed that adsorption capacity of crystal violet on EDTA-GO/corncob was higher compared with natural corncob and EDTA-corncob. The most suitable pH value of the solution is about 6.0, the adsorption equilibrium time is 200 min. EDTA-GO/corncob can be reused eight times. This study indicated that EDTA-GO/corncob is a reusable adsorbent for rapid, low-cost, and efficient removal of dye from waste water.

In this study, crystal violet dyes were adsorbed by EDTA functionalized corncob (EDTA-corncob) and EDTA/graphene oxide functionalized corncob (EDTA-GO/corncob), which were prepared using disodium ethylenediamine tetraacetic acid and the graphene oxide immersion method.