4-formyl dibenzo-18-crown-6 grafted polyvinyl alcohol as anion exchange membranes for fuel cell

Highly efficient removal of Sr2+ from aqueous solutions using a polyacrylic acid/crown-ether/graphene oxide hydrogel composite

With the development of nuclear power, efficiently treating nuclear wastes generated during operation has attracted extensive attention. Hydrogels are common adsorbent materials in the treatment of wastewater due to their high swelling rate and easy post-treatment. In this work, a novel polyacrylic acid/crown-ether/graphene oxide (PAA/DB18C6/GO) hydrogel composite was synthesized by a radical cross-linking copolymerization method and characterized using various analytical tools such as SEM, FT-IR, TGA and XPS. The effects of time, pH, initial Sr2+ concentration, and temperature on Sr2+ adsorption onto the PAA/DB18C6/GO were studied. The PAA/DB18C6/GO shows a high adsorption capacity of 379.35 mg g-1 at an initial Sr2+ concentration of 772 mg L-1 due to the unique structure of dibenzo-18-crown-ether-6 and high swelling. The composite has a high selectivity for Sr2+ with a removal rate of 82.4% when concentrations of Na+ and K+ were 10 times higher than that of Sr2+. The pH and temperature have no apparent impact on adsorption performance of the PAA/DB18C6/GO under the experimental conditions. The composite shows excellent reusability with more than 92% removal rate for Sr2+ after five continuous cycles. In addition, the mechanism of Sr2+ adsorption by PAA/DB18C6/GO was analyzed by fitting the adsorption data to the theoretical models and XPS data.

Effect of Crown Ether Additives on the Enhanced Performance of Metallic Bipolar Plates for Proton Exchange Membrane Fuel Cells

One of the key components of the fuel cell stack is a metallic bipolar plate (MBP) that plays multiple roles, such as current collector, fuel and oxidant distributor, and mechanical support. However, corrosion and consequent metal elution are major drawbacks of the MBP because they diminish the efficiency and power performance of membrane-electrode assemblies (MEAs). Herein, we show that the crown ether (CE) additive can simultaneously inhibit surface corrosion of the MBP and act as a scavenger for eluted metal ions to alleviate contamination of other components. From the electrochemical measurement, high-resolution imaging, and elemental analysis, we have found that the CE undergoes electrolytic decomposition and makes an efficient protective layer in an in situ manner. This layer prevents direct contact between the MBP and electrolyte as well as the dissolution of metal ions into the electrolyte. In addition, we demonstrate that the CE can improve the recovery protocol of the MEA owing to the formation of host-guest complexes between the CE and metal cations. These results provide key insights into the design of high-performance MBPs for proton-exchange membrane fuel cells.

A Brief Review of Poly(Vinyl Alcohol)-Based Anion Exchange Membranes for Alkaline Fuel Cells

Anion exchange membrane fuel cells have unique advantages and are thus gaining increasing attention. Poly(vinyl alcohol) (PVA) is one of the potential polymers for the development of anion exchange membranes. This review provides recent studies on PVA-based membranes as alternative anion exchange membranes for alkaline fuel cells. The development of anion exchange membranes in general, including the types, materials, and preparation of anion exchange membranes in the last years, are discussed. The performances and characteristics of recently reported PVA-based membranes are highlighted, including hydroxide conductivity, water uptake, swelling degree, tensile strength, and fuel permeabilities. Finally, some challenging issues and perspectives for the future study of anion exchange membranes are discussed.

Crown ether-based anion exchange membranes with highly efficient dual ion conducting pathways

Anion exchange membranes (AEMs) are a crucial constituent for alkaline fuel cells. As the core component of fuel cells, the low performance AEMs restrict the development and application of the fuel cells. Herein, the trade-off between the OH^- conductivity and dimensional stability was solved by constructing AEMs with adequate OH^- conductivity and satisfactory alkali resistance using Tröger's base (TB) poly (crown ether)s (PCEs) as the main chain, the embedded quaternary ammonium (QA) and Na⁺-functionalized crown ether units as the cationic group. Crown ether is an electron donator, and can capture Na⁺ to form Na⁺-functionalized crown ether units to conveniently transfer OH^- and significantly promote the alkaline stability of the AEMs. The influence of the Na⁺-functionalized crown ether units on the performance of AEMs was studied in detail. The PCEs based AEMs show an obvious hydrophobic-hydrophilic microphase separation. These features make them ideal platforms for the OH^- conduction applications. As expected, the as-prepared PCEs-QA-100% (100% is the degree of cross-linking) AEM with an ionic exchange capacity (IEC) of 2.07 meq g^-1 has a high OH^- conductivity of 159 mS cm^-1 at 80 °C. Furthermore, the membrane electrode assemblies fabricated using the PCEs-QA-100% AEM possess a maximum power density of 291 mW cm^-2 under the current density of 500 mA cm^-2.

Anion Exchange Composite Membranes Composed of Quaternary Ammonium-Functionalized Poly(2,6-dimethyl-1,4-phenylene oxide) and Silica for Fuel Cell Application

Anion exchange membranes (AEMs) with good alkaline stability and ion conductivity are fabricated by incorporating quaternary ammonium-modified silica into quaternary ammonium-functionalized poly(2,6-dimethyl-1,4-phenylene oxide) (QPPO). Quaternary ammonium with a long alkyl chain is chemically grafted to the silica in situ during synthesis. Glycidyltrimethylammoniumchloride functionalization on silica (QSiO₂) is characterized by Fourier transform infrared and transmission electron microscopic techniques. The QPPO/QSiO₂ membrane having an ion exchange capacity of 3.21 meq·g^-1 exhibits the maximum hydration number (λ = 11.15) and highest hydroxide ion conductivity of 45.08 × 10^-2 S cm^-1 at 80 °C. In addition to the high ion conductivity, AEMs also exhibit good alkaline stability, and the conductivity retention of the QPPO/QSiO₂-3 membrane after 1200 h of exposure in 1 M potassium hydroxide at room temperature is about 91% ascribed to the steric hindrance offered by the grafted long glycidyl trimethylammonium chain in QSiO₂. The application of the QPPO/QSiO₂-3 membrane to an alkaline fuel cell can yield a peak power density of 142 mW cm^-2 at a current density of 323 mA cm^-2 and 0.44 V, which is higher than those of commercially available FAA-3-50 Fumatech AEM (OCV: 0.91 V; maximum power density: 114 mW cm^-2 at current density: 266 mA cm^-2 and 0.43 V). These membranes provide valuable insights on future directions for advanced AEM development for fuel cells.

Adsorption behavior of copper ions using crown ether-modified konjac glucomannan

A novel supramolecular polysaccharide composite [KGM + DB18C6] was prepared from konjac glucomannan (KGM) and dibenzo-18-crown-6 (DB18C6) using ceric ammonium nitrate as initiator. The products were characterized by FTIR, TG, DSC, UV-Vis, XRD, solid-state ¹³C NMR, and SEM. Due to the introduction of crown ether, [KGM + DB18C6] showed good adsorption performance for Cu²⁺ in aqueous, and the maximum adsorption capacity was 194 mg/g under the optimal adsorption condition. The adsorption kinetics of [KGM + DB18C6] on Cu²⁺ could be described by the pseudo-second-order kinetic model. The adsorption isotherms of [KGM + DB18C6] on Cu²⁺ followed the dual-site Langmuir-Freundlich model. In addition, high recoveries of Cu²⁺ (from 82.65 to 88.47%), and low relative standard deviation (below 5.00%) were obtained by applying the product in real samples, indicating that [KGM + DB18C6] was a good absorbent for removing Cu²⁺ in wastewater.

Poly(Vinyl Alcohol) Recent Contributions to Engineering and Medicine

Poly(vinyl alcohol) (PVA) is a thermoplastic synthetic polymer, which, unlike many synthetic polymers, is not obtained by polymerization, but by hydrolysis of poly(vinyl acetate) (PVAc). Due to the presence of hydroxylic groups, hydrophilic polymers such as PVA and its composites made mainly with biopolymers are used for producing hydrogels that possess interesting morphological and physico-mechanical features. PVA hydrogels and other PVA composites are studied in light of their numerous application for electrical film membranes for chemical separation, element and dye removal, adsorption of metal ions, fuel cells, and packaging. Aside from applications in the engineering field, PVA, like other synthetic polymers, has applications in medicine and biological areas and has become one of the principal objectives of the researchers in the polymer domain. The review presents a few recent applications of PVA composites and contributions related to tissue engineering (repair and regeneration), drug carriers, and wound healing.

Multiple Enhancement Effects of Crown Ether in Tröger's Base Polymers on the Performance of Anion Exchange Membranes

The development of anion exchange membranes (AEMs) is hindered by the trade-off of ionic conductivity, alkaline stability, and mechanical properties. Tröger's base polymers (Tb-polymers) are recognized as promising membrane materials to overcome these obstacles. Herein, the AEMs made from Tb-poly(crown ether)s (Tb-PCEs) show good comprehensive performance. The influence of crown ether on the conductivity and alkaline stability of AEMs has been investigated in detail. The formation of hydronium ion-crown ether complexes and an obvious microphase-separated structure formed by the existence of crown ether can enhance the conductivity of the AEMs. The maximum OH^- conductivity of 141.5 mS cm^-1 is achieved from the Tb-PCEs based AEM (Tb-PCE-1) at 80 °C in ultrapure water. The ion-dipole interaction of the Na⁺ with crown ether can protect the quaternary ammonium from the attack of OH^- to improve the alkaline stability of AEMs. After 675 h of alkaline treatment, the OH^- conductivity of Tb-PCE-1 decreases by only 6%. The Tb-PCE-1-based single cell shows a peak power density of 0.202 W cm^-2 at 80 °C. The prominent physicochemical properties are attributed to the well-developed microstructure of the Tb-PCEs, as revealed by TEM, AFM, and SAXS observations.

Bioactive polymeric scaffolds for osteogenic repair and bone regenerative medicine

The loss of bone tissue is a striking challenge in orthopedic surgery. Tissue engineering using various advanced biofunctional materials is considered a promising approach for the regeneration and substitution of impaired bone tissues. Recently, polymeric supportive scaffolds and biomaterials have been used to rationally promote the generation of new bone tissues. To restore the bone tissue in this context, biofunctional polymeric materials with significant mechanical robustness together with embedded materials can act as a supportive matrix for cellular proliferation, adhesion, and osteogenic differentiation. The osteogenic regeneration to replace defective tissues demands greater calcium deposits, high alkaline phosphatase activity, and profound upregulation of osteocalcin as a late osteogenic marker. Ideally, the bioactive polymeric scaffolds (BPSs) utilized for bone tissue engineering should impose no detrimental impacts and function as a carrier for the controlled delivery and release of the loaded molecules necessary for the bone tissue regeneration. In this review, we provide comprehensive insights into different synthetic and natural polymers used for the regeneration of bone tissue and discuss various technologies applied for the engineering of BPSs and their physicomechanical properties and biological effects.