Dynamic network based on eugenol-derived epoxy as promising sustainable thermoset materials

High-Performance, Light-Stimulation Healable, and Closed-Loop Recyclable Lignin-Based Covalent Adaptable Networks

In this work, high-performance, light-stimulation healable, and closed-loop recyclable covalent adaptable networks are successfully synthesized from natural lignin-based polyurethane (LPU) Zn2+ coordination structures (LPUxZy). Using an optimized LPU (LPU-20 with a tensile strength of 28.4 ± 3.5 MPa) as the matrix for Zn2+ coordination, LPUs with covalent adaptable coordination networks are obtained that have different amounts of Zn. When the feed amount of ZnCl2 is 9 wt%, the strength of LPU-20Z9 reaches 37.3 ± 3.1 MPa with a toughness of 175.4 ± 4.6 MJ m-3 , which is 1.7 times of that of LPU-20. In addition, Zn2+ has a crucial catalytic effect on "dissociation mechanism" in the exchange reaction of LPU. Moreover, the Zn2+ -based coordination bonds significantly enhance the photothermal conversion capability of lignin. The maximum surface temperature of LPU-20Z9 reaches 118 °C under the near-infrared illumination of 0.8 W m-2 . This allows the LPU-20Z9 to self-heal within 10 min. Due to the catalytic effect of Zn2+ , LPU-20Z9 can be degraded and recovered in ethanol completely. Through the investigation of the mechanisms for exchange reaction and the design of the closed-loop recycling method, this work is expected to provide insight into the development of novel LPUs with high-performance, light-stimulated heal ability, and closed-loop recyclability; which can be applied toward the expanded development of intelligent elastomers.

Thiol-Aldehyde Polycondensation for Bio-based Adaptable and Degradable Phenolic Polymers

Designing sustainable materials with tunable mechanical properties, intrinsic degradability, and recyclability from renewable biomass through a mild process has become vital in polymer science. Traditional phenolic resins are generally considered to be not degradable or recyclable. Here we report the design and synthesis of linear and network structured phenolic polymers using facile polycondensation between natural aldehyde-bearing phenolic compounds and polymercaptans. Linear phenolic products are amorphous with Tg between -9 °C and 12 °C. Cross-linked networks from vanillin and its di-aldehyde derivative exhibited excellent mechanical strength between 6-64 MPa. The connecting dithioacetals are associatively adaptable strong bonds and susceptible to degradation in oxidative conditions to regenerate vanillin. These results highlight the potential of biobased sustainable phenolic polymers with recyclability and selective degradation, as a complement to the traditional phenol-formaldehyde resins.

From Lignins to Renewable Aromatic Vitrimers based on Vinylogous Urethane

During the two last decades, covalent adaptable networks (CANs) have proven to be an important new class of polymer materials combining the main advantages of thermoplastics and thermosets. For instance, materials can undergo reprocessing cycles by incorporating dynamic covalent bonds within a cross-linked network. Due to their versatility, renewable resources can be easily integrated into these innovative systems to develop sustainable materials, which can be related to the context of the recent development of a circular bioeconomy. Lignins, the main renewable sources of aromatic structures, are major candidates in the design of novel and biobased stimuli-responsive materials such as vitrimers due to their high functionality and specific chemical architectures. In the aim of developing recyclable lignin-based vinylogous urethane (VU) networks, an innovative strategy was elaborated in which lignin was first modified into liquid polyols and then into polyacetoacetates. Resulting macromonomers were integrated into aromatic VU networks and fully characterized through thermal, mechanical, and rheological experiments. Viscoelastic behaviors of the different aromatic vitrimers exhibited fast stress-relaxations (e. g., 39 s at 130 °C) allowing easy and fast mechanical reprocessing. A thermomechanical recycling study was successfully performed. Then, the developed strategy enabled the fabrication of healable biobased aromatic vitrimers with tunable structures and properties.

Contribution of the Surface Treatment of Nanofibrillated Cellulose on the Properties of Bio-Based Epoxy Nanocomposites Intended for Flexible Electronics

The growing interest in materials derived from biomass has generated a multitude of solutions for the development of new sustainable materials with low environmental impact. We report here, for the first time, a strategy to obtain bio-based nanocomposites from epoxidized linseed oil (ELO), itaconic acid (IA), and surface-treated nanofibrillated cellulose (NC). The effect of nanofibrillated cellulose functionalized with silane (NC/S) and then grafted with methacrylic acid (NC/SM) on the properties of the resulted bio-based epoxy systems was thoroughly investigated. The differential scanning calorimetry (DSC) results showed that the addition of NCs did not influence the curing process and had a slight impact on the maximum peak temperature. Moreover, the NCs improved the onset degradation temperature of the epoxy-based nanocomposites by more than 30 °C, regardless of their treatment. The most important effect on the mechanical properties of bio-based epoxy nanocomposites, i.e., an increase in the storage modulus by more than 60% at room temperature was observed in the case of NC/SM addition. Therefore, NC’s treatment with silane and methacrylic acid improved the epoxy–nanofiber interface and led to a very good dispersion of the NC/SM in the epoxy network, as observed by the SEM investigation. The dielectric results proved the suitability of the obtained bio-based epoxy/NCs materials as substitutes for petroleum-based thermosets in the fabrication of flexible electronic devices.

Twin-screw extrusion molding of a cellulose-based vitrimer containing a crosslinkable macromolecular plasticizer

Cellulose-based vitrimers were prepared using a crosslinkable macromolecular plasticizer and acetylated carboxymethyl cellulose via twin-screw extrusion. The cellulose-based material was toughened by the entanglement between the macromolecular plasticizer segments, and the exudation of the plasticizer was avoided by crosslinking. The prepared materials exhibited excellent hydrophobicity and shape memory properties. The plasticizer was evidently effective, and the reprocessing was completed at 130 °C within 15 min. The materials could be reprocessed at a lower temperature over a short period of time without any obvious degradation. After reprocessing three times, the material performance did not decrease significantly, thus showing good potential for regeneration and recycling.

Synthesis and characterization of new bio-based poly(acylhydrazone) vanillin vitrimers

New poly(acylhydrazone) vitrimeric-type materials derived from vanillin have been studied.

Influence of the Presence of Disulphide Bonds in Aromatic or Aliphatic Dicarboxylic Acid Hardeners Used to Produce Reprocessable Epoxidized Thermosets

The design of polymers from renewable resources with recycling potential comes from economic and environmental problems. This work focused on the impact of disulphide bonds in the dicarboxylic acids reactions with three epoxidized vegetable oils (EVOs). For the first time, the comparison between aromatic vs. aliphatic dicarboxylic acids, containing or not S-S bonds with EVOs was discussed and evaluated by dynamic scanning calorimetry. The obtained thermosets showed reprocessability, by the dual dynamic exchange mechanism. The virgin and reprocessed materials were characterized and the thermomechanical properties were compared. The thermosets derived from EVOs with high epoxy content combined with aromatic diacids containing disulphide bridges showed high glass transition values (~111 °C), high crosslink densities and good solvent stability.