Alginates as food ingredients absorb extra salt in sodium chloride-treated mice

Alginic acid-functionalized silver nanoparticles: A rapid monitoring tool for detecting the technology-critical element tellurium

The increasing global demand for tellurium, driven by its critical role in alloys, photovoltaic devices, and electronics, has raised concerns about its environmental pollution and neurotoxicity. In response, the potential of alginic acid (AA), a renewable, low-cost, and sustainable biopolymer, was explored for the biosynthesis of ultra-small silver nanoparticles (AgNPs) and their application in the detection of tellurium (Te(IV)). The effect of key synthesis parameters on desired physicochemical properties and yield of AgNPs was established to ensure high specificity and sensitivity towards Te(IV). The purified AgNPs with AA surface ligands were utilized to demonstrate a ratiometric absorbance sensor that exhibits excellent linearity and nanomolar-level affinity. This approach achieved a high correlation coefficient of ∼ 0.982, with a low detection limit of about 22 nM. Further investigations into the effect of pH, ionic strength, and organic molecules were conducted to elucidate detection performance and molecular understanding. The detection mechanism relies on the coordination between Te(IV) ions and the carboxylate groups of AA, which initiates aggregation-induced plasmon coupling in adjacent AgNPs. The capability of this analytical method to monitor Te(IV) in real-world water samples features its rapidity, user-friendliness, and suitability for point-of-care monitoring, making it a promising alternative to more complex techniques.

Alginic Acid Beads Containing Fluorescent Solvatochromic Dyes Display an Emission Color Response to a Cationic Surfactant

Lipophilic fluorescent dyes can be employed as sensors for surfactants present in concentrations above the critical micellar concentration (CMC) where the dyes are monodispersed in micelles. However, the surfactant concentration range over which these dyes are effective is narrowed because by the sigmoidal nature of their responses. To overcome this limitation, we developed a novel sensor material comprised of a labeled fluorescent solvatochromic dye covalently bonded to alginate gel, which is known to strongly adsorb cationic surfactants. We hypothesized that the dye-alginate conjugate would undergo fluorescent color changes in response to binding of surfactants which alter the polarity of the surrounding environment. Indeed, addition of the representative cationic surfactant, cetylpyridinium chloride (CPC), to an aqueous solution of the alginate conjugated fluorescent solvatochromic dye leads to a visible fluorescent color change when the concentration of CPC is below the CMC. The average values of the color appearance parameter, referred to as a hue, of light emitted from gels, calculated by analysis of fluorescence microscopy images using ImageJ software, were found to be approximately linearly dependent on the concentration of CPC encapsulated in the alginate-fluorescent dye complex. This finding shows that absorbed CPC can be quantitatively determined over a wide concentration range in the form of simple fluorescence wavelength or visible responses.

The Feasibility of Using Pulsed-Vacuum in Stimulating Calcium-Alginate Hydrogel Balls

The effect of the pulsed-vacuum stimulation (PVS) on the external gelation process of calcium-alginate (Ca-Alg) hydrogel balls was studied. The process was conducted at four different working pressures (8, 35, 61, and 101 kPa) for three pulsed-vacuum cycles (one cycle consisted of three repetitions of 10 min of depressurization and 10 min of vacuum liberation). The diffusion coefficients (D) of calcium cations (Ca²⁺) gradually reduced over time and were significantly pronounced (p < 0.05) at the first three hours of the external gelation process. The rate of weight reduction (WR) and rate of volume shrinkage (S_v) varied directly according to the D value of Ca²⁺. A significant linear relationship between WR and S_v was observed for all working pressures (R² > 0.91). An application of a pulsed vacuum at 8 kPa led to the highest weight reduction and shrinkage of Ca-Alg hydrogel samples compared to other working pressures, while 61 kPa seemed to be the best condition. Although all textural characteristics (hardness, breaking deformation, Young’s modulus, and rupture strength) did not directly variate by the level of working pressures, they were likely correlated with the levels of WR and S_v. Scanning electron micrographs (SEM) supported that the working pressure affected the characteristics of Ca-Alg hydrogel structure. Samples stimulated at a working pressure of 8 kPa showed higher deformation with heterogenous structure, large cavities, and looser layer when compared with those at 61 kPa. These results indicate the PVS is a promising technology that can be effectively applied in the external gelation process of Ca-Alg gel.