A new robotic system for CT-guided percutaneous procedures with haptic feedback

Evaluation of the performance of robot assisted CT-guided percutaneous needle insertion: Comparison with freehand insertion in a phantom

PURPOSE

To evaluate the performance of a novel robot for CT-guided needle positioning procedures and compare it to the freehand technique in an abdominal phantom.

METHODS

One interventional radiology fellow and one experienced interventional radiologist (IR) performed twelve robot-assisted and twelve freehand needle positionings in a phantom over predetermined trajectories. The robot automatically aimed a needle-guide according to the planned trajectories, after which the clinician manually inserted the needle. Using repeated CT scans, the needle position was assessed and adjusted if the clinician deemed it necessary. Technical success, accuracy, number of position adjustments, and procedure time were measured. All outcomes were analyzed using descriptive statistics and were compared between the robot-assisted and freehand procedures using the paired t-test and Wilcoxon signed rank test.

RESULTS

Compared with the freehand technique, the robot system improved the number of technically successfully needle targeting (20/24 vs 14/24), with higher accuracy (mean Euclidean deviation from target center: 3.5 ± 1.8 mm vs 4.6 ± 2.1 mm, p = 0.02) and required fewer needle position adjustments (0.0 ± 0.2 steps vs 1.7 ± 0.9 steps, p < 0.001), respectively. The robot improved the needle positioning for both, the fellow and the expert IR, compared to their freehand performances, with more improvement for the fellow than for the expert IR. The procedure time was similar for the robot-assisted and freehand procedures (19.5 ± 9.2 min. vs 21.0 ± 6.9 min., p = 0.777).

CONCLUSIONS

CT-guided needle positioning with the robot was more successful and accurate than freehand needle positioning and required fewer needle position adjustments without prolonging the procedure.

Review on Otological Robotic Systems: Toward Microrobot-Assisted Cholesteatoma Surgery

Otologic surgical procedures over time have become minimally invasive due to the development of medicine, microtechniques, and robotics. This trend then provides an expected reduction in the patient's recovery time and improvement in the accuracy of diagnosis and treatment. One of the most challenging difficulties that such techniques face are precise control of the instrument and supply of an ergonomic system to the surgeon. The objective of this literature review is to present requirements and guidelines for a surgical robotic system dedicated to middle ear surgery. This review is particularly focused on cholesteatoma surgery (diagnosis and surgical tools), which is one of the most frequent pathologies that urge for an enhanced treatment. This review also presents the current robotic systems that are implemented for otologic applications.

Design, Development, and Evaluation of a Master-Slave Surgical System for Breast Biopsy under Continuous MRI

Magnetic Resonance Imaging (MRI) provides superior soft-tissue contrast in cancer diagnosis compared to other imaging modalities. However, the strong magnetic field inside the MRI bore along with limited scanner bore size poses significant challenges. Since current approaches in breast biopsy using MR images is primarily a blind targeting approach, it is necessary to develop a MRI-compatible robot that can avoid multiple needle insertions into the breast tissue. This MRI-compatible robotic system could potentially lead to improvement in the targeting accuracy and reduce sampling errors. A master-slave surgical system has been developed comprising of a MRI-compatible slave robot which consists of one piezo motor and five pneumatic cylinders connected by long pneumatic transmission lines. The slave robot follows the configuration of the master robot, which provides an intuitive manipulation interface for the physician and operates inside the MRI bore to adjust the needle position and orientation and perform needle insertion task. Based on the MRI experiments using the slave robot, there was no significant distortion in the images and hence the slave robot can be safely operated inside the MRI with minimal loss in signal-to-noise ratio (SNR). Ex vivo and in vivo experiments have been conducted to evaluate the performance of the master-slave surgical system.

Needle insertion into soft tissue: a survey

Needle insertion in soft tissue has attracted considerable attention in recent years due to its application in minimally invasive percutaneous procedures such as biopsies and brachytherapy. This paper presents a survey of the current state of research on needle insertion in soft tissue. It examines the topic from several aspects, e.g. modeling needle insertion forces, modeling tissue deformation and needle deflection during insertion, robot-assisted needle insertion, and the effect of different trajectories on tissue deformation. All studies show that the axial force of a needle during insertion in soft tissue is the summation of different forces distributed along the needle shaft such as stiffness force, frictional force and cutting force. Some studies have modeled these forces. The force data in some procedures is used for identifying tissue layers as the needle is inserted or for path planning. Needle deflection and tissue deformation are major problems for accurate needle insertion and attempts have been made to model them. Using current models several insertion techniques have been developed which are briefly reviewed in this paper.

Today's state of the art in surgical robotics*

OBJECTIVE

This paper describes the current level of development of robots for surgery.

MATERIAL AND METHODS

This paper is based on a literature search in Pubmed, IEEExplore, CiteSeer and the abstract volumes of the MICCAI 2002, 2003 and 2004, CARS 2003 and 2004, CAOS 2003 and 2004, CURAC 2003 and 2004 and MRNV 2004 meetings.

RESULTS

Divided into different disciplines (imaging, abdominal and thoracic surgery, ENT, OMS, neurosurgery, orthopaedic surgery, radiosurgery, trauma surgery, urology), 159 robot systems are introduced. Their functionality, deployment, origin and mechanical set-up are described. Additional contacts and internet links are listed.

CONCLUSIONS

The systems perform diverse tasks such as milling cavities in bone, harvesting skin, screwing pedicles or irradiating tumors. From a technical perspective the strong specialization of the systems stands out. Most of the systems are being developed in Germany, the United States, Japan or France.