The preparation of poly(γ-glutamic acid)-NHS ester as a natural cross-linking agent of collagen

Encapsulation of Silicon Nano Powders via Electrospinning as Lithium Ion Battery Anode Materials

Silicon-containing polyester from tetramethoxysilane, ethylene glycol, and o-Phthalic anhydride were used as encapsulating materials for silicon nano powders (SiNP) via electrospinning, with Polyacrylonitrile (PAN) as spinning additives. In the correct quantities, SiNP could be well encapsulated in nano fibers (200-400 nm) using scanning electron microscopy (SEM). The encapsulating materials were then carbonized to a Si-O-C material at 755 °C (Si@C-SiNF-5 and Si@C-SiNF-10, with different SiNP content). Fiber structure and SiNP crystalline structure were reserved even after high-temperature treatment, as SEM and X-ray diffraction (XRD) verified. When used as lithium ion battery (LIB) anode materials, the cycling stability of SiNPs increased after encapsulation. The capacity of SiNPs decreased to ~10 mAh/g within 30 cycles, while those from Si@C-SiNF-5 and Si@C-SiNF-10 remained over 500 mAh/g at the 30th cycle. We also found that adequate SiNP content is necessary for good encapsulation and better cycling stability. In the anode from Si@C-SiNF-10 in which SiNPs were not well encapsulated, fibers were broken and pulverized as SEM confirmed; thus, its cycling stability is poorer than that from Si@C-SiNF-5.

In situ forming injectable γ-poly(glutamic acid)/PEG adhesive hydrogels for hemorrhage control

Rapidly in situ forming adhesive hydrogels are promising candidates for efficient hemostasis due to their easy administration and minimal invasion. However, development of biocompatible and high-performance hemostatic hydrogels without any additional toxic agents remains a challenge. Herein, a series of novel injectable adhesive hydrogels based on N-hydroxysuccinimide (NHS) modified γ-poly(glutamic acid) (γPGA-NHS) and tetra-armed poly(ethylene glycol) amine (Tetra-PEG-NH₂) were developed. Among all samples, PGA₁₀-PEG₁₅ and PGA₁₀-PEG₂₀ hydrogels with higher PEG contents exhibited rapid gelation time (<20 s), strong mechanical strength (compression modulus up to ∼75 kPa), good adhesive properties (∼15 kPa), and satisfactory burst pressure (∼18-20 kPa). As a result, PGA₁₀-PEG₁₅ and PGA₁₀-PEG₂₀ hydrogels showed a remarkable reduction in hemostasis time and blood loss compared with gauze and fibrin glue. More importantly, the PGA₁₀-PEG₂₀ hydrogel was also successfully used to seal femoral arterial trauma. Subcutaneous implantation experiments indicated a good biocompatibility of the hydrogels in vivo. All these results strongly support that the developed PGA-PEG hydrogels could serve as promising hemostatic agents in emergency and clinical situations.

4-Arm PEG-Functionalized Decellularized Pericardium for Effective Prevention of Postoperative Adhesion in Cardiac Surgery

Postoperative adhesions are a very common and serious complication in cardiac surgery, and the development of an effective anti-adhesion membrane showing resistance to the physical stimulus generated by the pulsation of the heart is desirable. In this study, an anti-adhesion material was developed through amine coupling between decellularized bovine pericardia (dBPCs) and 4-arm poly(ethylene glycol) succinimidyl glutarate (4-arm PEG-NHS) for the postoperative care of cardiac surgical patients. The efficacy of the 4-arm PEG-functionalized dBPCs in the prevention of adhesions after cardiac surgery was investigated in a rabbit heart adhesion model. The dBPCs meet the requirements for biocompatibility, flexibility, and sufficient suturable strength, and the 4-arm PEG moieties provide an anti-adhesion effect by the high excluded volume interactions of the PEG chains with proteins. The 4-arm PEG-functionalized dBPCs had a significantly greater anti-adhesion effect than the other materials tested and showed re-establishment of the mesothelial monolayer. These results suggested that the 4-arm PEG-functionalized dBPCs are a favorable material for an anti-adhesion membrane.

Poly(γ-glutamic acid) Nanocoating To Enhance the Viability of Pseudomonas stutzeri NRCB010 through Cell Surface Engineering

Microbial inoculants can enhance soil quality, promote plant nutrient acquisition, and alleviate problems caused by the excessive use of chemical fertilizers. However, susceptibility to harsh conditions during transport and storage, as well as the short shelf-life of plant growth-promoting rhizobacteria (PGPR), limit industrial application. Herein, a novel strategy to form nanocoating on bacterial surfaces to enhance viability was proposed. The nanocoating was composed of N-hydroxysuccinimide (NHS)-modified poly (γ-glutamic acid) (γ-PGA) and calcium ions, which could adhere to the surface of bacteria by forming covalent bonds and ionic bonds with the bacteria. The bacteria encapsulated in the coating had better resistance against harsh conditions than bare bacteria. The viability of coated bacteria was also increased by 2.38 times compared with bare bacteria after 4 weeks of storage. The pot experiment showed that coated Pseudomonas stutzeri NRCB010 had better growth-promoting properties compared with free P. stutzeri NRCB010. These results indicate that cell surface engineering is an effective method to enhance the resistance of bacteria against harsh conditions and is expected to promote the widespread use of PGPR.

Injectable Self-Healing Adhesive pH-Responsive Hydrogels Accelerate Gastric Hemostasis and Wound Healing

Endoscopic mucosal resection (EMR) and endoscopic submucosal dissection (ESD) are well-established therapeutics for gastrointestinal neoplasias, but complications after EMR/ESD, including bleeding and perforation, result in additional treatment morbidity and even threaten the lives of patients. Thus, designing biomaterials to treat gastric bleeding and wound healing after endoscopic treatment is highly desired and remains a challenge. Herein, a series of injectable pH-responsive self-healing adhesive hydrogels based on acryloyl-6-aminocaproic acid (AA) and AA-g-N-hydroxysuccinimide (AA-NHS) were developed, and their great potential as endoscopic sprayable bioadhesive materials to efficiently stop hemorrhage and promote the wound healing process was further demonstrated in a swine gastric hemorrhage/wound model. The hydrogels showed a suitable gelation time, an autonomous and efficient self-healing capacity, hemostatic properties, and good biocompatibility. With the introduction of AA-NHS as a micro-cross-linker, the hydrogels exhibited enhanced adhesive strength. A swine gastric hemorrhage in vivo model demonstrated that the hydrogels showed good hemostatic performance by stopping acute arterial bleeding and preventing delayed bleeding. A gastric wound model indicated that the hydrogels showed excellent treatment effects with significantly enhanced wound healing with type I collagen deposition, α-SMA expression, and blood vessel formation. These injectable self-healing adhesive hydrogels exhibited great potential to treat gastric wounds after endoscopic treatment.

In situ structural studies during denaturation of natural and synthetically crosslinked collagen using synchrotron SAXS

Collagen is an important biomacromolecule, making up the majority of the extracellular matrix in animal tissues. Naturally occurring crosslinks in collagen stabilize its intermolecular structure in vivo, whereas chemical treatments for introducing synthetic crosslinks are often carried out ex vivo to improve the physical properties or heat stability of the collagen fibres for applications in biomaterials or leather production. Effective protection of intrinsic natural crosslinks as well as allowing them to contribute to collagen stability together with synthetic crosslinks can reduce the need for chemical treatments. However, the contribution of these natural crosslinks to the heat stability of collagen fibres, especially in the presence of synthetic crosslinks, is as yet unknown. Using synchrotron small-angle X-ray scattering, the in situ role of natural and synthetic crosslinks on the stabilization of the intermolecular structure of collagen in skins was studied. The results showed that, although natural crosslinks affected the denaturation temperature of collagen, they were largely weakened when crosslinked using chromium sulfate. The development of synergistic crosslinking chemistries could help retain the intrinsic chemical and physical properties of collagen-based biological materials.

Factors affecting thermal stability of collagen from the aspects of extraction, processing and modification

Abstract

Collagen, as a thermal-sensitive protein, is the most abundant structural protein in animals. Native collagen has been widely applied in various fields due to its specific physicochemical and biological properties. The beneficial properties would disappear with the collapse of the unique triple helical structure during heating. Understanding thermal stability of collagen is of great significance for practical applications. Previous studies have shown the thermal stability would be affected by the different sources, extraction methods, solvent systems in vitro and modified methods. Accordingly, the factors affecting thermal stability of collagen are discussed in detail in this review.

Graphical abstract

Novel Modification of Collagen: Realizing Desired Water Solubility and Thermostability in a Conflict-Free Way

Because of poor water solubility and low thermostability, the application of collagen is limited seriously in fields such as injectable biomaterials and cosmetics. In order to overcome the two drawbacks simultaneously, a novel bifunctional modifier based on the esterification of polyacrylic acid (PAA) with N-hydroxysuccinimide (NHS) was prepared. The esterification degree of PAA-NHS esters was increased upon increasing the NHS dose, which was confirmed by Fourier-transform infrared (FTIR) and nuclear magnetic resonance spectrascopy. FTIR results indicated that the triple helix of the modified collagens remained integrated, whereas the molecular weight became larger, as reflected by the sodium dodecyl sulfate-polyacrylamide gel electrophoresis pattern. The modified collagens displayed excellent water solubility under neutral condition, owing to lower isoelectric point (3.1-4.3) than that of native collagen (7.1). Meanwhile, denaturation temperatures of the modified collagens were increased by 4.8-5.9 °C after modification. The modified collagen displayed hierarchical microstructures, as reflected by field-emission scanning electron microscopy, while atomic force microscopy further revealed a "fishing net-like" network in the nanoscale, reflecting a unique aggregation behavior of collagen macromolecules after modification. As a whole, the PAA-NHS ester as a bifunctional modifier endowed collagen with desired water solubility and thermostability in a conflict-free manner, which was beneficial to the process and application of the water-soluble collagen.

Transdermal transport of collagen and hyaluronic acid using water in oil microemulsion

Collagen and hyaluronic acid (HA) are biopolymers that affect the appearance and condition of the skin. Delivery of these compounds into the skin is highly challenging since have a number of disadvantageous properties, such as high molecular weight and hydrophilicity. Here, we evaluated the transdermal penetration of low and high molecular weight collagen and HA from microemulsions. A number of microemulsion formulations, differing in the content of polymers and surfactants (i.e. penetration promoters), were used for the permeation study. In addition, a correlation was made between the composition of these microemulsions and the polymers transport efficiency. The results indicate that, microemulsions enable transdermal permeation of collagen and HA. The concentration of polymers and the solubilization capacity of microemulsions had the greatest influence on the permeation. Surprisingly, the molecular weight of polymers and the content of other components affected the size of microemulsion particles, and thus these parameters had an indirect influence on the permeation process. This study demonstrated therefore the potential therapeutic use of microemulsion with collagen and HA in improving and regenerating the barrier of aged or diseased skin.

Diiron Dithiolate Complex Induced Helical Structure of Histone and Application in Photochemical Hydrogen Generation

Very-lysine-rich calf thymus histone proteins form disordered structure and hydrophobic interaction-driven aggregates in weakly acidic solution. We reported that the conjugation of diiron dithiolate complex to the lysine residues induced formation of helical conformation and condensed nanoassemblies with a high loading capacity up to 18.7 wt %. The incorporated diiron dithiolate complex showed photocatalytic activity for hydrogen evolution in aqueous solutions, with a turnover number (based on [FeFe] catalyst moiety) up to 359 that was more than 6 times that of the free catalyst. The increase of helical conformation in proteins was well correlated to the increasing enhancement of photocatalytic activity. We demonstrated that the [FeFe]-hydrogenase-mimic biohybrid system based on the photocatalyst-induced protein conformational conversion and reassembly is efficient for hydrogen generation regardless of the relatively large size.

Fluorescence studies on the aggregation behaviors of collagen modified with NHS-activated poly(γ-glutamic acid)

The poly(γ-glutamic acid)-NHS (γ-PGA-NHS) esters were used to endow collagen with both of excellent water-solubility and thermal stability via cross-linking reaction between γ-PGA-NHS and collagen. In the present work, the effect of γ-PGA-NHS on the aggregation of collagen molecules was studied by fluorescence techniques. The fluorescence emission spectra of pyrene in collagen solutions and the intrinsic fluorescence emission spectra of collagen suggested different effects of γ-PGA-NHS on collagen molecules: inhibiting aggregation below critical aggregation concentration (CAC) and promoting aggregation above CAC. The two-dimensional (2D) fluorescence correlation spectra indicated that the intermolecular hydrogen bonding and cross-linking between γ-PGA-NHS and collagen would influence the aggregation of collagen molecules. By the ultra-sensitive differential scanning calorimeter (VP-DSC), it was found that the main denaturational transition temperature (T_m2) of modified collagen increased, while its calorimetric enthalpy changes (ΔH₂) decreased compared to those of native collagen, further indicating that the modification of γ-PGA-NHS influenced the aggregation of collagen molecules. The study provide useful information for the utilizing and or the processing of water-soluble collagen in aqueous solution in the fields such as cosmetics, health care products, tissue engineering and biomedical materials, etc.

Effect of carboxymethylcellulose on fibril formation of collagen in vitro

The effect of carboxymethylcellulose (CMC) on the fibril formation of collagen in vitro was studied by turbidity measurements and atomic force microscopy (AFM). The kinetics curves of fibril formation indicated that the rate of collagen fibrillogenesis was decreased with the addition of CMC, meanwhile the final turbidity was obviously increased as the CMC/collagen ratio reached 30%. The AFM images of collagen-CMC solutions showed that the number of nucleation sites of collagen fibrillogenesis was significantly increased with the presence of CMC, while the diameter of immature collagen fibrils was obviously decreased. Moreover, the thermal stability of collagen fibril hydrogels was obviously improved with the presence of CMC. In addition, the morphologies of collagen fibrils observed by AFM revealed that the adjacent fibril segments or fibrils were intertwisted and even tightly merged, probably due to the hydrogen bonding and molecular entanglement interactions between CMC and collagen molecules.

Collagen and hyaluronic acid hydrogel in water-in-oil microemulsion delivery systems

The increase in skin related health issues has promoted interest in research on the efficacy of microemulsion in dermal and transdermal delivery of active ingredients. Here, we assessed the water-in-oil microemulsion capacity to incorporate two natural polymers, i.e. collagen and hyaluronic acid with low and high molecular weight. Systems were extensively characterized in terms of conductivity, phase inversion studies, droplet diameter, polydispersity index and rheological properties. The results of this research indicate that the structure and extent of water phase in microemulsions is governed by ratio and amount of surfactant mixture (sorbitan ester derivatives). However, results have also shown that collagen, depending upon the weight of the molecule and its surface activity, influence the droplet size of the microemulsions. While the hyaluronic acid, especially with high molecular weight, due to the water-binding ability and hydrogel formation alters the rheological properties of the microemulsion, thus providing viscous consistency of the formulation.