In vitro osteogenic potential of collagen/chitosan-based hydrogels-silica particles hybrids in human bone marrow-derived mesenchymal stromal cell cultures

Innovative Vancomycin-Loaded Hydrogel-Based Systems - New Opportunities for the Antibiotic Therapy

Purpose

Surgical site infections pose a significant challenge for medical services. Systemic antibiotics may be insufficient in preventing bacterial biofilm development. With the local administration of antibiotics, it is easier to minimize possible complications, achieve drugs' higher concentration at the injured site, as well as provide their more sustained release. Therefore, the main objective of the proposed herein studies was the fabrication and characterization of innovative hydrogel-based composites for local vancomycin (VAN) therapy.

Methods

Presented systems are composed of ionically gelled chitosan particles loaded with vancomycin, embedded into biomimetic collagen/chitosan/hyaluronic acid-based hydrogels crosslinked with genipin and freeze-dried to serve in a flake/disc-like form. VAN-loaded carriers were characterized for their size, stability, and encapsulation efficiency (EE) using dynamic light scattering technique, zeta potential measurements, and UV-Vis spectroscopy, respectively. The synthesized composites were tested in terms of their physicochemical and biological features.

Results

Spherical structures with sizes of about 200 nm and encapsulation efficiencies reaching values of approximately 60% were obtained. It was found that the resulting particles exhibit stability over time. The antibacterial activity of the developed materials against Staphylococcus aureus was established. Moreover, in vitro cell culture study revealed that the surfaces of all prepared systems are biocompatible as they supported the proliferation and adhesion of the model MG-63 cells. In addition, we have demonstrated significantly prolonged VAN release while minimizing the initial burst effect for the composites compared to bare nanoparticles and verified their desired physicochemical features during swellability, and degradation experiments.

Conclusion

It is expected that the developed herein system will enable direct delivery of the antibiotic at an exposed to infections surgical site, providing drugs sustained release and thus will reduce the risk of systemic toxicity. This strategy would both inhibit biofilm formation and accelerate the healing process.

In vitro/ex vivo evaluation of multifunctional collagen/chitosan/hyaluronic acid hydrogel-based alendronate delivery systems

Injectable hydrogel-based materials have emerged as promising alendronate (ALN) delivery systems for the treatment of osteoporosis. However, their intrinsic permeability limits the sustained delivery of small-molecule drugs. In response to this challenge, we present the multifunctional hybrids composed of mesoporous silica particles decorated with hydroxyapatite and loaded with alendronate (MSP-NH2-HAp-ALN), which are immobilized in collagen/chitosan/hyaluronic acid-based hydrogel. We have mainly focused on the biological in vitro/ex vivo evaluation of developed composites. It was found that the extracts released from tested systems do not exhibit hemolytic properties and are safe for blood elements and the human liver cell model. The resulting materials create an environment conducive to differentiating human bone marrow mesenchymal stem cells and reduce the viability of osteoclast precursors (RAW 264.7). Importantly, even the system with the lowest concentration of ALN caused a substantial cytotoxic effect on RAW 264.7 cells; their viability decreased to 20 % and 10 % of control on 3 and 7 day of culture. Additionally, prolonged ALN release (up to 20 days) with minimized burst release was observed, while material features (wettability, swellability, degradation, mechanical properties) depended on MSP-NH2-HAp-ALN content. The obtained data indicate that developed composites establish a high-potential formulation for safe and effective osteoporosis therapy.

The Diamond Concept Enigma: Recent Trends of Its Implementation in Cross-linked Chitosan-Based Scaffolds for Bone Tissue Engineering

An increasing number of publications over the past ten years have focused on the development of chitosan-based cross-linked scaffolds to regenerate bone tissue. The design of biomaterials for bone tissue engineering applications relies heavily on the ideals set forth by a polytherapy approach called the "Diamond Concept". This methodology takes into consideration the mechanical environment, scaffold properties, osteogenic and angiogenic potential of cells, and benefits of osteoinductive mediator encapsulation. The following review presents a comprehensive summarization of recent trends in chitosan-based cross-linked scaffold development within the scope of the Diamond Concept, particularly for nonload-bearing bone repair. A standardized methodology for material characterization, along with assessment of in vitro and in vivo potential for bone regeneration, is presented based on approaches in the literature, and future directions of the field are discussed.

Proliferative and Osteogenic Supportive Effect of VEGF-Loaded Collagen-Chitosan Hydrogel System in Bone Marrow Derived Mesenchymal Stem Cells

The use of hydrogel (HG) in regenerative medicine is an emerging field and thus several approaches have been proposed recently to find an appropriate hydrogel system. In this sense, this study developed a novel HG system using collagen, chitosan, and VEGF composites for culturing mesenchymal stem cells (MSCs), and investigated their ability for osteogenic differentiation and mineral deposition. Our results showed that the HG loaded with 100 ng/mL VEGF (HG-100) significantly supported the proliferation of undifferentiated MSCs, the fibrillary filament structure (HE stain), mineralization (alizarin red S and von Kossa stain), alkaline phosphatase, and the osteogenesis of differentiated MSCs compared to other hydrogels (loaded with 25 and 50 ng/mL VEGF) and control (without hydrogel). HG-100 showed a higher VEGF releasing rate from day 3 to day 7 than other HGs, which substantially supports the proliferative and osteogenic properties of HG-100. However, the HGs did not increase the cell growth in differentiated MSCs on days 14 and 21 due to the confluence state (reach stationary phase) and cell loading ability, regardless of the VEGF content. Similarly, the HGs alone did not stimulate the osteogenesis of MSCs; however, they increased the osteogenic ability of MSCs in presence of osteogenic supplements. Accordingly, a fabricated HG with VEGF could be used as an appropriate system to culture stem cells for bone and dental regeneration.

Towards Controlling the Local Bone Tissue Remodeling-Multifunctional Injectable Composites for Osteoporosis Treatment

Alendronate (ALN) is the most commonly prescribed oral nitrogen-containing bisphosphonate for osteoporosis therapy. However, its administration is associated with serious side effects. Therefore, the drug delivery systems (DDS) enabling local administration and localized action of that drug are still of great importance. Herein, a novel multifunctional DDS system based on the hydroxyapatite-decorated mesoporous silica particles (MSP-NH₂-HAp-ALN) embedded into collagen/chitosan/chondroitin sulfate hydrogel for simultaneous osteoporosis treatment and bone regeneration is proposed. In such a system, the hydrogel serves as a carrier for the controlled delivery of ALN at the site of implantation, thus limiting potential adverse effects. The involvement of MSP-NH₂-HAp-ALN in the crosslinking process was established, as well as the ability of hybrids to be used as injectable systems. We have shown that the attachment of MSP-NH₂-HAp-ALN to the polymeric matrix provides a prolonged ALN release (up to 20 days) and minimizes the initial burst effect. It was revealed that obtained composites are effective osteoconductive materials capable of supporting the osteoblast-like cell (MG-63) functions and inhibiting osteoclast-like cell (J7741.A) proliferation in vitro. The purposely selected biomimetic composition of these materials (biopolymer hydrogel enriched with the mineral phase) allows their biointegration (in vitro study in the simulated body fluid) and delivers the desired physicochemical features (mechanical, wettability, swellability). Furthermore, the antibacterial activity of the composites in in vitro experiments was also demonstrated.

Design and development of biodegradable POSS-PCL-Zeolite (β) nano-scaffold for potential applications in bone regeneration

Side effects caused by bone fractures and restrictions on bone regeneration impose an enormous economic burden on the health system of society. To overcome these limitations, tissue engineering and cell-based therapies have been proposed as alternatives to induce and promote bone healing. Still, bone regeneration disadvantages, such as limited and painful surgery, the risk of infection, nerve injury, bleeding, and function damage, have led investigators to find an alternative therapy. In some studies, bone stimulants have prompted scientists to design scaffolds with appropriate physical structure with the possibility of cell adhesion and proliferation, which plays an influential role in the regeneration and repair of bone tissue. PCL nanofiber is an absorbing candidate for the formulation of biocompatible scaffolds used in tissue engineering. To overcome these negative aspects, improve the properties of PCL nanofibers, and based on the biocompatibility and superior mechanical properties of POSS, Polyhedral Oligomeric Silsesquioxane-Polycaprolactone-Zeolite (POSS-PCL-Zeolite) nanocomposite electrospun nanofiber scaffolds were fabricated in the present study. Nanohybrids and nanofibers structures were characterized by FTIR, HNMR, XRD, SEM, EDX, and DSC techniques. We used cellular and molecular assays, including DCFH ROS detection system, gene expression (RUNX-2, Osteocalcin, Nrf2, BAX, VEGF gens), and apoptotic to demonstrate the biocompatibility and induce bone differentiation of formulated POSS-PCL-Zeolite scaffolds. The results showed the biodegradability of POSS-PCL-Zeolite Nano-scaffold and supported the nesting of mesenchymal stem cells (MSCs) and induced bone differentiation by POSS-PCL-Zeolite Nano-scaffold.

Clindamycin-Loaded Halloysite Nanotubes as the Antibacterial Component of Composite Hydrogel for Bone Repair

A new drug delivery system consisting of clindamycin phosphate entrapped in acid-etched halloysite nanotubes was successfully prepared and characterized. It was then used as an antibacterial component of the multicomponent hydrogel designed as a material for bone regeneration. First, halloysite (HNT) was etched and clindamycin phosphate (CP) was entrapped in both raw and modified nanotubes, resulting in HNT-CP and EHNT-CP systems. They were characterized using SEM, TEM, TGA and FTIR; the entrapment efficiency and release of CP from both systems were also studied. EHNT-CP was then used as an antibacterial component of the two hydrogels composed of alginate, collagen and β-TCP. The hydrogels were prepared using different crosslinking procedures but had the same composition. The morphology, porosity, degradation rate, CP release profile, cytocompatibility, antibacterial activity and ability to induce biomineralization were studied for both materials. The hydrogel obtained by a chemical crosslinking with EDC followed by the physical crosslinking with calcium ions had better properties and was shown to have potential as a bone repair material.

Effects of pre-osteogenic differentiation on the bone regeneration potentiality of marrow mesenchymal stem cells/poly(ethylene glycol)-diacrylate hydrogel using a rat cranial defect model

Transplanting cell/hydrogel constructs into a bone defect site is an effective strategy to repair the damaged tissues. However, before transplantation, there are various methods to culture cell/hydrogel constructs. Especially, the preferred pre-osteogenic differentiation period to achieve satisfied bone regeneration should be determined. To this end, Bone marrow mesenchymal stem cells (BMSCs) were firstly photo-encapsulated into poly(ethylene glycol)-diacrylate (PEGDA) hydrogel. Then the constructs were implanted in rat calvarial defects after being osteogenically induced for 0, 7, 14, and 21 days. In vitro experiments demonstrated that the proliferation of BMSCs in the hydrogels deceased significantly from 0 day to 7 days. The activity and the gene expression of alkaline phosphatase, besides the gene expression of bone morphogenetic protein-2 peaked at day 14, whereas the gene expression of osteocalcin and the formation of calcium nodules increased with the prolongation of differentiation time. In vivo results showed that limited areas of newly formed bone were found in the day0 and day21 groups. In the day7 group, obvious new bone with bone marrow space was found, while the day14 group nearly achieved complete bone healing. Our data suggested that the period of in vitro pre-osteogenic differentiation played a crucial role for the osteogenesis of BMSCs/PEGDA hydrogels. Furthermore, we found that a pre-differentiation for 14 days is preferable for bone regeneration in the rat cranial defects.

Lysine-functionalized chondroitin sulfate improves the biological properties of collagen/chitosan-based injectable hydrogels

Novel bioactive collagen/chitosan/lysine-functionalized chondroitin sulfate (CS_mod) injectable hydrogels are presented. The modification of CS with amine groups introduced with lysine moieties (the degree of substitution about 21%) guarantees its covalent binding with the hydrogel network while genipin crosslinking. Both the physicochemical and biological features of developed hydrogels might be adjusted by playing with CS_mod and crosslinking agent concentrations. It was revealed that materials became more hydrophobic with increased CS_mod content, while crosslinking degree and enzymatic degradation studies established the influence of CS_mod concentration and Ch:CS_mod ratio on the crosslinking process. In situ rheological experiments verified the injectability of resulted systems. The biological in vitro evaluation demonstrated that all designed materials are biocompatible as they supported proliferation and adhesion of MG-63 cell line. In vitro biomineralization study employing simulated body fluid model revealed CS_mod-content dependent bioactivity of obtained hydrogels. Importantly for pristine collagen/chitosan materials, the formation of apatite-like structures was not observed. Our findings demonstrate that developed injectable ColChCS_mod hydrogels particularly system with the greatest CS_mod concentration exhibits high bioactive potential, without the need of applying additional inducers what renders them promising materials within tissue engineering applications.

Addressing the Osteoporosis Problem-Multifunctional Injectable Hybrid Materials for Controlling Local Bone Tissue Remodeling

Novel multifunctional biomimetic injectable hybrid systems were synthesized. The physicochemical as well as biological in vitro and in vivo tests demonstrated that they are promising candidates for bone tissue regeneration. The hybrids are composed of a biopolymeric collagen/chitosan/hyaluronic acid matrix and amine group-functionalized silica particles decorated with apatite to which the alendronate molecules were coordinated. The components of these systems were integrated and stabilized by cross-linking with genipin, a compound of natural origin. They can be precisely injected into the diseased tissue in the form of a viscous sol or a partially cross-linked hydrogel, where they can serve as scaffolds for locally controlled bone tissue regeneration/remodeling by supporting the osteoblast formation/proliferation and maintaining the optimal osteoclast level. These materials lack systemic toxicity. They can be particularly useful for the repair of small osteoporotic bone defects.

Chitosan-based blends for biomedical applications

Polysaccharides are the most abundant naturally available carbohydrate polymers; composed of monosaccharide units covalently connected together. Chitosan is the most widely used polysaccharides because of its exceptional biocompatibility, mucoadhesion, and chemical versatility. However, it suffers from a few drawbacks, e.g. poor mechanical properties and antibacterial activity for biomedical applications. Blending chitosan with natural or synthetic polymers may not merely improve its physicochemical and mechanical properties, but may also improve its bioactivity-induced properties. This review paper summarizes progress in chitosan blends with biodegradable polymers and polysaccharides and their biomedical applications. Blends of chitosan with alginate, starch, cellulose, pectin and dextran and their applications were particularly addressed. The critical and challenging aspects as well as the future ahead of the use of chitosan-based blends were eventually enlightened.

The preparation and application of calcium phosphate biomedical composites in filling of weight-bearing bone defects

Nowadays, artificial bone materials have been widely applied in the filling of non-weight bearing bone defects, but scarcely ever in weight-bearing bone defects. This study aims to develop an artificial bone with excellent mechanical properties and good osteogenic capability. Firstly, the collagen-thermosensitive hydrogel-calcium phosphate (CTC) composites were prepared as follows: dissolving thermosensitive hydrogel at 4 °C, then mixing with type I collagen as well as tricalcium phosphate (CaP) powder, and moulding the composites at 37 °C. Next, the CTC composites were subjected to evaluate for their chemical composition, micro morphology, pore size, Shore durometer, porosity and water absorption ability. Following this, the CTC composites were implanted into the muscle of mice while the 70% hydroxyapatite/30% β-tricalcium phosphate (HA/TCP) biomaterials were set as the control group; 8 weeks later, the osteoinductive abilities of biomaterials were detected by histological staining. Finally, the CTC and HA/TCP biomaterials were used to fill the large segments of tibia defects in mice. The bone repairing and load-bearing abilities of materials were evaluated by histological staining, X-ray and micro-CT at week 8. Both the CTC and HA/TCP biomaterials could induce ectopic bone formation in mice; however, the CTC composites tended to produce larger areas of bone and bone marrow tissues than HA/TCP. Simultaneously, bone-repairing experiments showed that HA/TCP biomaterials were easily crushed or pushed out by new bone growth as the material has a poor hardness. In comparison, the CTC composites could be replaced gradually by newly formed bone and repair larger segments of bone defects. The CTC composites trialled in this study have better mechanical properties, osteoinductivity and weight-bearing capacity than HA/TCP. The CTC composites provide an experimental foundation for the synthesis of artificial bone and a new option for orthopedic patients.

Tailoring cellular microenvironments using scaffolds based on magnetically-responsive polymer brushes

A variety of polymeric scaffolds with the ability to control cell detachment has been created for cell culture using stimuli-responsive polymers. However, the widely studied and commonly used thermo-responsive polymeric substrates always affect the properties of the cultured cells due to the temperature stimulus. Here, we present a different stimuli-responsive approach based on poly(3-acrylamidopropyl)trimethylammonium chloride) (poly(APTAC)) brushes with homogeneously embedded superparamagnetic iron oxide nanoparticles (SPIONs). Neuroblastoma cell detachment was triggered by an external magnetic field, enabling a non-invasive process of controlled transfer into a new place without additional mechanical scratching and chemical/biochemical compound treatment. Hybrid scaffolds obtained in simultaneous surface-initiated atom transfer radical polymerization (SI-ATRP) were characterized by atomic force microscopy (AFM) working in the magnetic mode, secondary ion mass spectrometry (SIMS), and X-ray photoelectron spectroscopy (XPS) to confirm the magnetic properties and chemical structure. Moreover, neuroblastoma cells were cultured and characterized before and after exposure to a neodymium magnet. Controlled cell transfer triggered by a magnetic field is presented here as well.

Injectable thermosensitive hybrid hydrogel containing graphene oxide and chitosan as dental pulp stem cells scaffold for bone tissue engineering

Here, we fabricated thermosensitive injectable hydrogel containing poly (N-isopropylacrylamide) (PNIPAAm)-based copolymer/graphene oxide (GO) composite with different feed ratio to chitosan (CS) as a natural polymer through physical and chemical crosslinking for the proliferation and differentiation of the human dental pulp stem cells (hDPSCs) to the osteoblasts. The PNIPAAm copolymer/GO composite was synthesized by free-radical copolymerization of (N-isopropylacrylamide) (NIPAAm), itaconic acid (IA) and maleic anhydride-modified poly(ethylene glycol) (PEG) in the presence of GO and used for the preparation of the hydrogels. The formulated hydrogels were evaluated for the porous architecture, rheological behavior, compressive strength, swelling property, in vitro degradation, hemocompatibility, biocompatibility, and differentiation. The hydrogel could enhance the deposition of minerals and the activity of alkaline phosphatase (ALP), in large part attributable to the oxygen and amine-containing functional groups of GO and CS. The engineered hydrogel could also upregulate the expression of the Runt-related transcription factor 2 and osteocalcin in the hDPSCs cultivated in both the normal and osteogenic media. It seems to promote the absorption of osteogenic inducer too. Based on our findings, the engineered hydrogel demonstrated the osteogenic potential, upon which it is proposed as a constructing scaffold in bone tissue engineering for the transplantation of hDPSCs.

Polysaccharide-Based Systems for Targeted Stem Cell Differentiation and Bone Regeneration

Bone tissue engineering is an ever-changing, rapidly evolving, and highly interdisciplinary field of study, where scientists try to mimic natural bone structure as closely as possible in order to facilitate bone healing. New insights from cell biology, specifically from mesenchymal stem cell differentiation and signaling, lead to new approaches in bone regeneration. Novel scaffold and drug release materials based on polysaccharides gain increasing attention due to their wide availability and good biocompatibility to be used as hydrogels and/or hybrid components for drug release and tissue engineering. This article reviews the current state of the art, recent developments, and future perspectives in polysaccharide-based systems used for bone regeneration.

Bioactive yet antimicrobial structurally stable collagen/chitosan/lysine functionalized hyaluronic acid - based injectable hydrogels for potential bone tissue engineering applications

Novel, biocompatible, multifunctional, injectable genipin crosslinked collagen/chitosan/lysine-modified hyaluronic acid based hydrogels (ColChHA_mod) were prepared in a facile, one-step procedure. The novelty of the current approach lies in the functionalization of hyaluronic acid (HA) with primary amine groups by lysine attachment, and its further use as a component of the injectable sol. The obtained derivative, HA_mod, could form, upon crosslinking with genipin, covalent bonds with other components of the hydrogel network, resulting in structurally stable, better-defined hydrogels. We have demonstrated that, by adjusting HA_mod content and genipin concentration, hydrogels with tunable physicochemical characteristics (swelling, wettability, tendency for enzymatic degradation) and properties adequate for the potential bone tissue regeneration can be prepared. Storage modulus measurements indicated that HA_mod has positive effect on mechanical characteristics of hydrogels prepared. It was also revealed that the ColChHA_mod-based hydrogels are characterized by a high porosity (85-95%). The in situ rheological measurements confirmed the injectability of the obtained hydrogels. The in vitro cell culture studies showed that the surface of all materials prepared was biocompatible, as they supported proliferation and adhesion of osteoblast-like cells followed by ALP expression. The intrinsic antibacterial activity of the hydrogels against Escherichia coli was also demonstrated in in vitro experiment.

Combination of Human Amniotic Fluid Derived-Mesenchymal Stem Cells and Nano-hydroxyapatite Scaffold Enhances Bone Regeneration

BACKGROUND:

Human amniotic fluid-derived stem cells (hAF-MSCs) have a high proliferative capacity and osteogenic differentiation potential in vitro. The combination of hAF-MSCs with three-dimensional (3D) scaffold has a promising therapeutic potential in bone tissue engineering and regenerative medicine. Selection of an appropriate scaffold material has a crucial role in a cell supporting and osteoinductivity to induce new bone formation in vivo.

AIM:

This study aimed to investigate and evaluate the osteogenic potential of the 2nd-trimester hAF-MSCs in combination with the 3D scaffold, 30% Nano-hydroxyapatite chitosan, as a therapeutic application for bone healing in the induced tibia defect in the rabbit.

SUBJECT AND METHODS:

hAF-MSCs proliferation and culture expansion was done in vitro, and osteogenic differentiation characterisation was performed by Alizarin Red staining after 14 & 28 days. Expression of the surface markers of hAF-MSCs was assessed using Flow Cytometer with the following fluorescein-labelled antibodies: CD34-PE, CD73-APC, CD90-FITC, and HLA-DR-FITC. Ten rabbits were used as an animal model with an induced defect in the tibia to evaluate the therapeutic potential of osteogenic differentiation of hAF-MSCs seeded on 3D scaffold, 30% Nano-hydroxyapatite chitosan. The osteogenic differentiated hAF-MSCs/scaffold composite system applied and fitted in the defect region and non-seeded scaffold was used as control. The histopathological investigation was performed at 2, 3, & 4 weeks post-transplantation and scanning electron microscope (SEM) was assessed at 2 & 4 weeks post-transplantation to evaluate the bone healing potential in the rabbit tibia defect.

RESULTS:

Culture and expansion of 2nd-trimester hAF-MSCs presented high proliferative and osteogenic potential in vitro. Histopathological examination for the transplanted hAF-MSCs seeded on the 3D scaffold, 30% Nano-hydroxyapatite chitosan, demonstrated new bone formation in the defect site at 2 & 3 weeks post-transplantation as compared to the control (non-seeded scaffold). Interestingly, the scaffold accelerated the osteogenic differentiation of AF-MSCs and showed complete bone healing of the defect site as compared to the control (non-seeded scaffold) at 4 weeks post-transplantation. Furthermore, the SEM analysis confirmed these findings.

CONCLUSION:

The combination of the 2nd-trimester hAF-MSCs and 3D scaffold, 30% Nano-hydroxyapatite chitosan, have a therapeutic perspective for large bone defect and could be used effectively in bone tissue engineering and regenerative medicine.

Genipin crosslinked bioactive collagen/chitosan/hyaluronic acid injectable hydrogels structurally amended via covalent attachment of surface-modified silica particles

Collagen, chitosan and hyaluronic acid based multicomponent injectable and in situ gellating biomimetic hybrid materials for bone tissue engineering applications were prepared in one-step procedure. The bioactive phase in the form of surface-modified silica particles was introduced to the solutions of biopolymers and simultaneously crosslinked with genipin both the biopolymer matrix and dispersed particles at 37 °C. The novel approach presented here involved the use of silica particles which surfaces were priory functionalized with amino groups. That modification makes possible the covalent attachment of silica particles to the polymeric hydrogel network on crosslinking with genipin. That methodology is especially important as it makes possible to obtain the hybrid materials (biopolymer-silica particles) in which the problems related to the potential phase separation of mineral particles, hindering their in vivo application can be eliminated. The hybrids of various compositions were obtained and their physicochemical and biological properties were determined. The in vitro experiments performed under simulated body fluid conditions revealed that the amino-functionalized silica particles covalently attached to the biopolymeric network are still bioactive. Finally, the in vitro cell culture studies shown that the materials developed are biocompatible as they supported MG-63 cells adhesion, proliferation as well as Alkaline phosphatase (ALP) expression.

Influence of in vitro differentiation status on the in vivo bone regeneration of cell/chitosan microspheres using a rat cranial defect model

The aim of this study was to investigate the influence of the in vitro osteogenic differentiation status on the in vivo bone regeneration of cell/chitosan microspheres qualitatively and quantitatively. To this end, rat bone-marrow-derived mesenchymal stromal cells (BMSCs) were seeded onto apatite-coated chitosan microspheres. The constructs were osteogenically differentiated for 0, 7, 14, and 21 days followed by calvarial defect implantation in vivo for up to 8 weeks. In vitro studies showed that BMSCs in the constructs proliferated from day 0 to day 7. The activity and gene expression of alkaline phosphatise increased from day 0 to day 14 and then decreased. The gene expression of collagen type I and osteocalcin peaked at day 21. In vivo, constructs retrieved from day 0 group were filled with fibrous tissues and capillaries, but no bone formation was observed. Constructs retrieved from day 7 and day 21 groups showed progressive bone formation, whereas those retrieved from day 14 group had the highest percentage of bone formation. These data suggested that to generate a substantial amount of bone in vivo, not only the in vitro osteogenic differentiation was necessary, but also the period of pre-differentiation was important for the cell-scaffold constructs. The period of pre-differentiation for 14 days was found to be the most suitable for chitosan microspheres.

Collagen/chitosan/hyaluronic acid - based injectable hydrogels for tissue engineering applications - design, physicochemical and biological characterization

Studies on synthesis, physico-chemical and biological properties of novel biomimetic materials, potentially useful as injectable hydrogels are presented. These materials are in situ prepared chemically crosslinked collagen/chitosan/hyaluronic acid-based hydrogels exhibiting potential for tissue regeneration. Optimization of hydrogels involved testing the effect of various concentration of crosslinking agent (genipin) as well as different ratios of biopolymers used on their properties. The changes in the content of hyaluronic acid and in the genipin concentration used have been shown to be crucial. Employing the highest concentration of crosslinking agent studied (20 mM) the hydrogels of compact structure, characterized by good mechanical properties and prolonged degradation profile can be obtained. Changing the HA content in sol mixture the hydrogel of various wettability; more or less hydrophilic when compared to pure collagen/chitosan hydrogels can be fabricated. The in vitro cell culture study has shown that the surface of the prepared materials ensures suitable biocompatibility. These hydrogels can support the proliferation and adhesion of MG-63 cell line as it was demonstrated using Alamar Blue assay and SEM observations. It is believed that the collagen/chitosan/hyaluronic acid hydrogels crosslinked with genipin are particularly promising materials for bone regeneration procedures, especially attractive for regeneration of small bone losses. This is the first paper in the litearature presenting results of studies on that type of biopolymeric injectable hydrogels chemically crosslinked with genipin.