Chemical modification of sodium alginate with thiosemicarbazide for the removal of Pb(II) and Cd(II) from aqueous solutions

Insight into the impact of environmental factors on heavy metal adsorption by sodium alginate hydrogel: Inspiration on applicable scenarios

Sodium alginate (SA) emerges as a promising adsorbent for the remediation of heavy metal-polluted wastewater. However, the systematic investigations on how and the extent to which the various compositions in real water matrices impact its performance were essential but rare when considering its use. Here, we explored the effect of common environmental factors on Cu(II) adsorption by an as-synthesized SA-based hydrogel (SAH). The result showed that high concentration of organics (above 10 mg L-1) had a negative influence on heavy metal removal (decreased by 9.45 % at least), while inorganic ion, turbidity and antibiotics at relatively low concentrations exhibited a negligible even promoting effect (increased by 9.8 % with the presence of 5 mg L-1 Nor). Based on above results and corresponding mechanism analyses, the possible applicable and unsuitable scenarios of SAH can be predicted. SAH could be a great candidate for treating heavy metal-polluted water such as river and lake water, while it is not a good option for electroplating or livestock wastewater which contains high concentration of organic matters. Besides, the operating conditions including pH (5.0 for Cu(II), 6.0 for Ni(II)), contact time (24 h), temperature (298 K) et al. were also determined. Overall, this work provides theoretical guidance and operational strategies for promoting the practical application of SA adsorbent in water treatment.

A critical review of sodium alginate-based composites in water treatment

The global freshwater crisis is a pressing issue, especially in areas with little rainfall and inner continental regions. The growing attention to water scarcity has induced increased interest in research on advanced water treatment technologies. As an abundant bioactive material in nature, sodium alginate (SA) has been widely used in water management due to its outstanding water absorption and holding ability, reversible swelling property, and pollutant adsorption performance. Building on this, progress made in using various modified forms of SA to access clean water is addressed in this review. Covering studies concern the adsorption and separation of pollutants in wastewater by SA-based absorbents and freshwater harvesting by SA-based collectors. This review explores SA-based composites' composition-structure-construction designs and emphasizes the impact of materials like inorganic materials, functional polymers, and porous matrices and how they can be exploited for water treatment. It also highlights the mechanisms of contaminants adsorption and freshwater desorption of SA-based composites. Finally, the shortcomings and future orientation of SA-based composites are proposed, including performance optimization, structural modification, application expansion, and mechanism in-depth investigation. This review aims to offer a theoretical basis and technical guidance for the use of natural materials to respond to the shortage of freshwater resources.

The Development of Alginate/Ag NPs/Caffeic Acid Composite Membranes as Adsorbents for Water Purification

Since the water pollution problem still affects the environmental system and human health, the need to develop innovative membranes has become imperious. Lately, researchers have focused on developing novel materials to help diminish the contamination problem. The aim of present research was to obtain innovative adsorbent composite membranes based on a biodegradable polymer, alginate, to remove toxic pollutants. Of all pollutants, lead was chosen due to its high toxicity. The composite membranes were successfully obtained through a direct casting method. The silver nanoparticles (Ag NPs) and caffeic acid (CA) from the composite membranes were kept at low concentrations, which proved enough to bestow antimicrobial activity to the alginate membrane. The obtained composite membranes were characterised by Fourier transform infrared spectroscopy and microscopy (FTIR), scanning electron microscopy (SEM), and thermogravimetric analysis (TG-DSC). Swelling behaviour, lead ion (Pb²⁺) removal capacity, regeneration and reusability were also determined. Further, the antimicrobial activity was tested against selected pathogenic strains (S. aureus, E. faecalis sp., P. aeruginosa, E. coli and C. albicans). The presence of Ag NPs and CA improves the antimicrobial activity of the newly developed membranes. Overall, the composite membranes are suitable for complex water treatment (removal of heavy metal ions and antimicrobial treatment).

The selective and sustainable separation of Cd(II) using C6MImT/[C6MIm]PF6 extractant

Cadmium has been classified as a kind of human carcinogens, and has a strong mobility in the water environment and this can result in serious harm to human health and environmental safety. Here, a new selective and efficient extraction-recovery strategy for Cd purification is provided by using C₆MimT/[C₆Mim]PF₆ as the green extractant. Due to the high compatibility between C₆MimT and [C₆Mim]PF₆, C₆MimT-Cd was efficiently separated from the aqueous phase. When the concentration of Cd(II) was 1000 mg/L, the extraction rate could reached 99.9 %. By comparing [C₆MIm]BF₄ with [C₆MIm]PF₆, the hydrophobicity restrained the ion exchange between cation and Cd and significantly reduced the loss of extractant. The extracted Cd(II) was separated in the form of precipitation after stripping. The extraction system of C₆MimT/[C₆Mim]PF₆ was stable after several extraction-stripping cycles. The extraction of Cd(II) by C₆MimT/[C₆Mim]PF₆ system mainly realized by forming a neutral and extractable cadmium complexes between Cd(II) and thione. Based on the natural complexation mechanism between metal and C₆MImT, Cd exists as obvious competitive advantage in coordination with C₆MimT compare to Pb, Zn, Mg, Cr, Fe. This work overcomes the problems of extractant loss and organic pollution caused by volatile or ion exchange, which can only reduce environmental hazards, but also promote the recovery of cadmium and other valuable resources.

Solid phase synthesis of oxidized sodium alginate-tobramycin conjugate and its application for infected wound healing

Although sodium alginate possesses excellent biocompatibility, moisture retention and easy availability, it cannot be directly applied for infected wound treatment. Herein, a solid phase synthesis strategy was proposed to fabricate oxidized sodium alginate-tobramycin conjugate (OSA-TOB) for anti-infection dressing development. 13C nuclear magnetic resonance spectra indicated that the oxidization process does not change the ratio of β-D-mannuronic acid (M) / α-L-guluronic acid (G) in OSA and the oxidization reaction shows no stereoselectivity. Elemental analysis disclosed that the graft ratio of tobramycin in OSA-TOB is 13.8 %. Antibacterial test indicated that OSA-TOB can effectively inhibit four prevalent pathogenic bacterial S.epidermidis, P. aeruginosa, S. aureus and E. coli via a different antibacterial mechanism compared to the original TOB. Hemolysis and cytotoxicity assays shown that OSA-TOB have superior hemocompatibility and cytocompatibility. Infected wound healing assay shown that the healing rate of OSA-TOB is the highest. Further analysis indicated that OSA-TOB can reduce the local inflammatory response, accelerate the form of epithelium and collagen deposition. In conclusions, OSA-TOB synthesized in solid phase can be potentially applied as a promising anti-infection wound dressing.

Effective biosorption of Cu(II) using hybrid biocomposite based on N-maleated chitosan/calcium alginate/titania: Equilibrium sorption, kinetic and thermodynamic studies

In this research work, a hybrid biocomposite based on N-maleated chitosan, amino-thiocarbamate functionalised calcium alginate and anhydrous Titania nanoparticles (NMC-MCA-TiO₂) was fabricated. The study involves the one pot facile synthesis of N-maleated chitosan and amino-thiocarbamate functionalised alginate under moderate conditions. Sorbent was conditioned in the form of hydrogel beads and characterized through FT-IR and SEM analysis. Newly grafted functional groups could act as potential chelating sites for enhanced Cu(II) sorption. Modified biopolymers were organo-functionalised which provided excellent support for immobilization of Titania nanoparticles (TiO₂) as inorganic filler. Kinetic data illustrated the manifestation of intrinsic chemisorption instead of simple bulk/film diffusion. Equilibrium sorption data fitted well with Freundlich adsorption model (R² ≈ 0.99) which designated the heterogeneous nature of sorbent. Maximum sorption capacity of biosorbent was found 192 mg/g at 298 K and pH = 6.0. Standard Gibbs free energy change ∆G^o (-21.53, -21.97, and - 22.42 kJ/mol), standard enthalpy change ∆H^o (5.12 kJ/mol) and standard entropy change ∆S^o (0.09 kJ/mol K^-1) values suggested that the sorption process to be spontaneous and endothermic. The sorbent 3NMC-MCA-TiO₂ could be competitive candidate for economical and rapid adsorptive removal of Cu(II) from dilute contaminated liquids.

Synthesis of hybrid biosorbent based on 1,2-cyclohexylenedinitrilotetraacetic acid modified crosslinked chitosan and organo-functionalized calcium alginate for adsorptive removal of Cu(II)

The present study is based on the synthesis of a novel hybrid biosorbent using 1,2-cyclohexylenedinitrilotetraacetic acid modified crosslinked chitosan and amino-thiocarbamate moiety functionalized sodium alginate (CDTA-CS/TSC-CA). The fabricated sorbent was employed to investigate the efficient recovery of Cu(II) from aqueous media. CDTA-CS/TSC-CA was characterized using Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). Analysis confirmed the successful modification of both biopolymers and subsequent loading of Cu(II) ions. CDTA-CS/TSC-CA was casted in the form of hydrogel beads having different CDTA-CS to TSC-CA mass ratios i.e., 10.0-40.0% by mass. The hydrogel beads 4CDTA-CS/TSC-CA with CDTA-CS/TSC-CA mass ratio of 40.0% was found most effective for copper sorption. Equilibrium sorption results showed that initial concentration of copper, medium pH, contact time, sorbent dosage and temperature influenced the sorption capacity (q_e). Rate of sorption data was interpreted using different kinetic models and found best fitted with pseudo second order rate expression (R² ≈ 0.99), illustrating that the rate determining step includes the electron density transfer from sorbent coordination sites to central copper ions. Crank's RIDE equation and Elovich chemisorption model (ECM) revealed the presence of two sorption phases, initially rapid sorption followed by comparatively a slow uptake. Equilibrium sorption data was well depicted by Langmuir model and maximum monolayer adsorption capacity (q_m) was computed as 276.53 mg·g^-1 at 298 K. Standard Gibbs free energy change, ∆G° (-19.99, -20.18 and -20.36 kJ/ mol), standard enthalpy change, ∆H° (-8.95 kJmol) and standard entropy change, ∆S° (0.04 kJ/mol K^-1) values suggested that the adsorption process is spontaneous and exothermic. Hence, 4CDTA-CS/TSC-CA was found efficient biosorbent for copper removal from its dilute effluents.

Recent progress, synthesis, and applications of chitosan-decorated magnetic nanocomposites in remediation of dye-laden wastewaters

Over the past several decades, the disposal of dyes from the industrial manufacturing sector has had an inadvertent impact on water ecology as polluted water bodies with these hazardous dyes...

Xanthate-modified alginates for the removal of Pb(II) and Ni(II) from aqueous solutions: A brief analysis of alginate xanthation

Mining is the most common activity that introduces heavy metal ions into aquatic ecosystems, especially in low income-developing nations where governments are implementing stricter regulations for industrial wastewater. In this context, this work is focused on the application of xanthate-modified alginates for the removal of Pb(II) and Ni(II) from aqueous solutions. In order to confirm the presence of xanthate groups alongside alginate chains, characterization by second-derivative FT-IR was carried out and significance evidence attributed to xanthate groups was found at around 1062-1079 cm^-1, 829-845 cm^-1 and 620-602 cm^-1. In addition to this, thermogravimetric analysis and differential scanning calorimetry were employed to explore thermal properties of modified alginates. According to these results, enthalpy changes (∆H) characteristic of dehydration and collapse of biopolymeric structure were estimated as +11.41 J/g and -6.83 J/g, respectively. Furthermore, the presence of S element was confirmed by EDS mapping technique, whereas FESEM image showed a cracked and homogeneous surface distribution. On the other hand, the effect of important parameters such as pH, dosage, initial concentration as well as Langmuir and Freundlich isotherm were deeply discussed. Finally, rheological measurements were performed aiming to investigate the gel-like viscoelastic features associated to nickel xanthate compound.

Alginate-based adsorbents for removal of metal ions and radionuclides from aqueous solutions: A review

The presence of heavy metal and radionuclides in water bodies has been a long-lasting environmental problem which results in many undesirable consequences. In this framework, the biosorption process, which uses inexpensive and naturally produced material such as alginate, is an alternative technology in the environmental remediation. This review provides relevant and recent literature regarding the application of alginate and its derivatives on removal of various heavy metal ions and radionuclides. The effects of process variables such as solution pH, adsorbent dosage, metal ion concentration, contact time, temperature and co-existing ions used in batch studies in addition to kinetic, isothermal models as well as thermodynamic that fit the adsorption experimental data are critically discussed. This review also includes mechanisms involved during adsorption process. Furthermore, future research needs for the removal of contaminants by alginate-based materials with the aims of improving their adsorption performance and their practical applications are commented.

ER, Venâncio T, Valderrama AC. Functionalization of an Alginate-Based Material by Oxidation and Reductive Amination

This research focused on the synthesis of a functional alginate-based material via chemical modification processes with two steps: oxidation and reductive amination. In previous alginate functionalization with a target molecule such as cysteine, the starting material was purified and characterized by UV-Vis, ¹H-NMR and HSQC. Additionally, the application of FT-IR techniques during each step of alginate functionalization was very useful, since new bands and spiked signals around the pyranose ring (1200–1000 cm⁻¹) and anomeric region (1000–750 cm⁻¹) region were identified by a second derivative. Additionally, the presence of C₁-H₁ of β-D-mannuronic acid residue as well as C₁-H₁ of α-L-guluronic acid residue was observed in the FT-IR spectra, including a band at 858 cm⁻¹ with characteristics of the N-H moiety from cysteine. The possibility of attaching cysteine molecules to an alginate backbone by oxidation and post-reductive amination processes was confirmed through ¹³C-NMR in solid state; a new peak at 99.2 ppm was observed, owing to a hemiacetal group formed in oxidation alginate. Further, the peak at 31.2 ppm demonstrates the presence of carbon -CH₂-SH in functionalized alginate—clear evidence that cysteine was successfully attached to the alginate backbone, with 185 μmol of thiol groups per gram polymer estimated in alginate-based material by UV-Visible. Finally, it was observed that guluronic acid residue of alginate are preferentially more affected than mannuronic acid residue in the functionalization.

Xanthation of alginate for heavy metal ions removal. Characterization of xanthate-modified alginates and its metal derivatives

Xanthates are widely used in mining industry as collectors for its high affinity towards metal sulfides and precious metal ores. The possibility of using alginate for xanthation has not been explored yet despite the feasibility by the presence of hydroxyl groups alongside the polymeric chains. Therefore, this work aims to evaluate the alginate as a matrix for xanthation and its application on heavy metal ions removal. In order to obtain green materials, important pararmeter were explored such as the effect of reaction time (4-12 h), type of base (NaOH/KOH) and amount of carbon disulfide (2-10%v/v). Xanthated alginates were analyzed by NMR techniques and evidence of β-elimination was detected at 5.45 ppm. Furthermore, the presence of S element was confirmed by EDS mapping technique, while XRD showed a semi-crystalline structure. On the other hand, the chemical shifts of δ(C=S) and ν(C=S) bands were found around 863-805 cm^-1 and 662-602 cm^-1 respectively. Also, a shoulder at 182 ppm is appreciated by NMR in solid state attributed to CS group. According to FESEM analyses, morphology of xanthated alginates is affected by interaction with heavy metal ions. Finally, suitable materials for the removal of heavy metal ions were established at optimum pH values.

Applications of solid-state NMR spectroscopy in environmental science

Environmental science is an interdisciplinary field, which integrates chemical, physical, and biological sciences to study environmental problems and human impact on the environment. This article highlights the use of solid-state NMR spectroscopy (SSNMR) in studies of environmental processes and remediation with examples from both laboratory studies and samples collected in the field. The contemporary topics presented include soil chemistry, environmental remediation (e.g., heavy metals and radionuclides removal, carbon dioxide mineralization), and phosphorus recovery. SSNMR is a powerful technique, which provides atomic-level information about speciation in complex environmental samples as well as the interactions between pollutants and minerals/organic matter on different environmental interfaces. The challenges in the application of SSNMR in environmental science (e.g., measurement of paramagnetic nuclei and low-gamma nuclei) are also discussed, and perspectives are provided for the future research efforts.

Sustainable dialdehyde polysaccharides as versatile building blocks for fabricating functional materials: An overview

Dialdehyde polysaccharide (DAP), containing multiple aldehyde groups, can react with materials having amino groups via Schiff base crosslinking. Besides, it can also react with materials having carbonyl/hydroxyl groups via aldol reactions. Based on these intriguing properties, DAPs can be employed as versatile building blocks to fabricate functional materials used in biomedical field, wastewater treatment, leather manufacture, and electrochemistry field. This review aims to provide an overview of the recent advances in fabricating biomaterials, adsorbents, leather tanning agents, and electrochemical materials based on DAPs. The basic fabricating strategy and principle of these materials and their performances are overall summarized, along with a discussion of associated scalability challenges, technological strategies to overcome them, and the prospect for commercial translations of this versatile material. Blending the versatility of DAP with material science and technological advances can provide a powerful tool to develop more DAP-based functional materials in a scalable way.

An innovative strategy for synchronous treatment of combined heavy metal and organic pollutants through polysaccharide gel encapsulating S2

In many industrial fields, treatment of composite contaminations involving inorganic heavy metal ions and organic pollutants simultaneously remains a tremendous challenge. In this paper, an innovative strategy based on the gelation process of Sodium Alginate (SA) was proposed for synchronous treatment of composite pollutants. Through a pre-gelation step, SA gel balls encapsulated with S2- (SA/S2- gel) were formed and immersed into polluted solutions containing Pb2+/Cd2+ and Cd2+/dye. The removal efficiency of Pb2+/Cd2+ by SA/S2- gel were both increased compared with pure SA gel. The adsorbed Pb2+/Cd2+ was in-situ transformed into PbS/CdS quantum dots (QDs) possessing photo-catalytic activity, which induced the degradation of dyes under UV irradiation. In this respect, the proposed SA/S2- system might provide a high-performance and energy-saving way for comprehensive treatment of inorganic heavy metal and organic industrial pollutants.

Strategies to Functionalize the Anionic Biopolymer Na-Alginate without Restricting Its Polyelectrolyte Properties

The natural anionic polyelectrolyte alginate and its derivatives are of particular interest for pharmaceutical and biomedical applications. Most interesting for such applications are alginate hydrogels, which can be processed into various shapes, self-standing or at surfaces. Increasing efforts are underway to functionalize the alginate macromolecules prior to hydrogel formation in order to overcome the shortcomings of purely ionically cross-linked alginate hydrogels that are hindering the progress of several sophisticated biomedical applications. Particularly promising are derivatives of alginate, which allow simultaneous ionic and covalent cross-linking to improve the physical properties and add biological activity to the hydrogel. This review will report recent progress in alginate modification and functionalization with special focus on synthesis procedures, which completely conserve the ionic functionality of the carboxyl groups along the backbone. Recent advances in analytical techniques and instrumentation supported the goal-directed modification and functionalization.

TV, Huamani-Palomino RG, Baena-Moncada AM. Simultaneous adsorption of a ternary mixture of brilliant green, rhodamine B and methyl orange as artificial wastewater onto biochar from cocoa pod husk waste. Quantification of dyes using the derivative spectrophotometry method

Biochar obtained from cocoa pod husk waste for the simultaneous adsorption of a ternary mixture of brilliant green, rhodamine B and methyl orange.

Dithiocarbamate-modified cellulose-based sorbents with high storage stability for selective removal of arsenite and hazardous heavy metals

A series of cellulose derivatives bearing dialkyl dithiocarbamate (DTC) groups were synthesized. Their ability of sorption of arsenite (As(iii)) and heavy metals and their storage stability in the solid state were investigated. Among them, DTC-modified cellulose derived from l-proline showed the highest sorption capacity for As(iii) and heavy metals to selectively remove them from aqueous media. It also showed exellent storage stability in air at 40 °C.

Dithiocarbamate-modified cellulose derived from l-proline works as a storable sorbent for selective removal of toxic As(iii) and heavy metals from aqueous media.

Adsorption of Cr(III) and Pb(II) by graphene oxide/alginate hydrogel membrane: Characterization, adsorption kinetics, isotherm and thermodynamics studies

Graphene oxide/alginate hydrogel membranes (GAHMs) were prepared by cross-linking a casting solution (blending graphene oxide, sodium alginate and urea) with a calcium chloride solution. The adsorption performance and mechanism for the removel of Cr(III) and Pb(II) were investigated. The GAHMs, before and after adsorption, were characterized by FT-IR, SEM, EDX and XPS, and their hydrophilicity was determined. The kinetics, isotherm and thermodynamics models were introduced. Results indicated that the optimal pH for the membranes removing Cr(III) and Pb(II) was 6.0 and 5.0 respectively. The adsorption capacity for both metal ions was positively correlated with the initial concentration and contact time and their adsorption was consistent with the pseudo-second-order kinetic model. The Langmuir isotherm better described the adsorption equilibrium. Moreover, the Langmuir model showed that the maximum adsorption capacity for Pb(II) was better than that for Cr(III) (327.9 and 118.6 mg/g, respectively). Thermodynamics analysis showed that the adsorption for Cr(III) by GAHMs was endothermic, whereas that of Pb(II) was exothermic. After five adsorption-desorption cycles, a high adsorption efficiency for both metal ions was maintained. This novel membrane material (GAHMs) is potentially an effective membrane adsorbent for the removal of Cr(III) and Pb(II) ions in practical applications.