Influence of initial chemical composition and characteristics of pulps on the production and properties of lignocellulosic nanofibers

Thermal Characterizations of Waste Cardboard Kraft Fibres in the Context of Their Use as a Partial Cement Substitute within Concrete Composites

The building and construction industry consumes a significant amount of virgin resources and minimizing the demand with alternative waste materials can provide a contemporary solution. In this study, thermal components of kraft fibres (KFs) derived from waste cardboard are investigated. The mechanical properties containing KFs within concrete composites are evaluated. Metakaolin (MK) and KFs were integrated into concrete samples as a partial substitute for cement. Silica Fume (SF) was applied to the KF (SFKFs) with a view to enhancing the fibre durability. The results indicated that there was a reduction in compressive strength of 44 and 56% when 10% raw and modified KFs were integrated, respectively. Raw, fibre and matrix-modified samples demonstrated a 35, 4 and 24% flexural strength reduction, respectively; however, the tensile strength improved by 8% when the matrix was modified using MK and SFKF. The morphology of the fibres was illustrated using a scanning electron microscope (SEM), with an energy dispersion X-ray spectroscopy (EDS) provision and Fourier transform infrared spectroscopy (FT-IR) employed to gain insights into their chemical nature. The thermal, calorimetric and combustion attributes of the fibres were measured using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and pyrolysis combustion flow calorimetry (PCFC). SFKFs showed a lower heat release capacity (HRC), demonstrating a lower combustion propensity compared to raw KFs. Furthermore, the 45% decreased peak heat release rate (pHRR) of SFKFs highlighted the overall reduction in the fire hazards associated with these materials. TGA results also confirmed a lower mass weight loss of SFKFs at elevated temperatures, thus corroborating the results from the PCFC runs.

Effect of Oxalic Acid Concentration and Different Mechanical Pre-Treatments on the Production of Cellulose Micro/Nanofibers

The present work analyzes the effect of process variables and the method of characterization of cellulose micro/nanofibers (CMNFs) obtained by different treatments. A chemical pre-treatment was performed using oxalic acid at 25 wt.% and 50 wt.%. Moreover, for mechanical pre-treatments, a rotary homogenizer or a PFI mill refiner were considered. For the mechanical fibrillation to obtain CMNFs, 5 and 15 passes through a pressurized homogenization were considered. The best results of nanofibrillation yield (76.5%), transmittance (72.1%) and surface charges (71.0 µeq/g CMNF) were obtained using the PFI mill refiner, 50 wt.% oxalic acid and 15 passes. Nevertheless, the highest aspect ratio (length/diameter) determined by Transmission Electron Microscopy (TEM) was found using the PFI mill refiner and 25 wt.% oxalic acid treatment. The aspect ratio was related to the gel point and intrinsic viscosity of CMNF suspensions. The values estimated for gel point agree with those determined by TEM. Moreover, a strong relationship between the intrinsic viscosity [η] of the CMNF dispersions and the corresponding aspect ratio (p) was found (ρ[η] = 0.014 p^2.3, R² = 0.99). Finally, the tensile strength of films obtained from CMNF suspensions was more influenced by the nanofibrillation yield than their aspect ratio.

Influence of hemicellulose content and cellulose crystal change on cellulose nanofibers properties

This study aimed to evaluate the properties of cellulose nanofibers (CNFs) with different hemicellulose contents and cellulose II polymorphs. A link was found between these polysaccharides and the properties of CNFs. A decrease in crystallinity (from 69 to 63%) and changes in the crystalline structure of cellulose subjected to an alkaline environment were observed, promoting the partial conversion of cellulose I to cellulose II (from 2 to 42%) and preventing CNFs production at NaOH concentrations higher than 5%. Most treatments showed pseudoplastic fluid behavior, except for the 10% NaOH treatment over 2 h, which showed Newtonian fluid behavior. The quality index of the reference CNFs (TEMPO-oxidized) was the highest (80 ± 3), followed by that of the 5% NaOH-treated (68 ± 3 and 22% energy savings compared to the untreated sample), and the untreated (63 ± 3) samples; and the 10% NaOH treatments had quality indices of 51 ± 3 and 32 ± 1, respectively.

Characterization of Porous Structures of Cellulose Nanofibrils Loaded with Salicylic Acid

Bleached and unbleached pulp fibers were treated with 2,2,6,6-tetramethylpyperidine-1-oxyl (TEMPO) mediated oxidation to obtain cellulose nanofibrils (CNFs). The resulting bleached and unbleached CNFs were mixed with salicylic acid (0, 5, 10, 20 wt%) before casting and freeze-drying or 3D-printing. A series of methods were tested and implemented to characterize the CNF materials and the porous structures loaded with salicylic acid. The CNFs were characterized with atomic force microscopy and laser profilometry, and release of salicylic acid was quantified with UV-visible absorbance spectroscopy, conductivity measurements, and inductive coupled plasma mass spectrometry (ICP-MS). Fourier-transform infrared spectroscopy (FTIR) complemented the analyses. Herein, we show that aerogels of bleached CNFs yield a greater release of salicylic acid, compared to CNF obtained from unbleached pulp. The results suggest that biodegradable constructs of CNFs can be loaded with a plant hormone that is released slowly over time, which may find uses in small scale agricultural applications and for the private home market.