Preparation and characterization of thermosensitive chitosan/carboxymethylcellulose/scleroglucan nanocomposite hydrogels

Nanocellulose/scleroglucan-enhanced robust, heat-resistant composite hydrogels for oilfield water plugging

In an oil exploitation process, hydrogel plugging agents can effectively reduce the water-oil intermixing, decrease water extraction volume, and enhance oil recovery rate. The practical applications of traditional polyacrylamide (PAM) hydrogel plugging agents in oilfield are limited by their non-biodegradability, poor mechanical performance, and inferior temperature-resistance. This work developed a mechanically stable and high-temperature-resistant composite hydrogel (STP) by incorporating biodegradable scleroglucan (Slg) and TEMPO-oxidized cellulose nanofibers (TOCN) in the PAM hydrogel. The addition of Slg conferred heat resistance to the PAM hydrogel, while TOCN reinforced the mechanical strength. Anti-aging analyses revealed that the STP endured for 108 h in a saline environment at 140 °C. In the water flooding characterization, the STP displayed a breakthrough pressure of 42.10 psi/ft. at a flow rate of 0.75 cm3/min. Under these extreme conditions, the plugging pressure reached 14.74 psi/ft., meeting the essential criteria for oilfield water plugging. This research demonstrates the potential of polysaccharides in the preparation of sustainable, tough, and heat-resistant water plugging materials.

Hydrogel loaded with thiolated chitosan modified taxifolin liposome promotes osteoblast proliferation and regulates Wnt signaling pathway to repair rat skull defects

To alleviate skull defects and enhance the biological activity of taxifolin, this study utilized the thin-film dispersion method to prepare paclitaxel liposomes (TL). Thiolated chitosan (CSSH)-modified TL (CTL) was synthesized through charge interactions. Injectable hydrogels (BLG) were then prepared as hydrogel scaffolds loaded with TAX (TG), TL (TLG), and CTL (CTLG) using a Schiff base reaction involving oxidized dextran and carboxymethyl chitosan. The study investigated the bone reparative properties of CTLG through molecular docking, western blot techniques, and transcriptome analysis. The particle sizes of CTL were measured at 248.90 ± 14.03 nm, respectively, with zeta potentials of +36.68 ± 5.43 mV, respectively. CTLG showed excellent antioxidant capacity in vitro. It also has a good inhibitory effect on Escherichia coli and Staphylococcus aureus, with inhibition rates of 93.88 ± 1.59 % and 88.56 ± 2.83 % respectively. The results of 5-ethynyl-2 '-deoxyuridine staining, alkaline phosphatase staining and alizarin red staining showed that CTLG also had the potential to promote the proliferation and differentiation of mouse embryonic osteoblasts (MC3T3-E1). The study revealed that CTLG enhances the expression of osteogenic proteins by regulating the Wnt signaling pathway, shedding light on the potential application of TAX and bone regeneration mechanisms.

One-step fabrication of millimeter-scale hollow vesicles with chitosan /DADMAC/ sodium alginate graft copolymer for enhanced anionic dye adsorption

Hollow vesicles are promising in water treatment due to their unique structure of the membrane and inner cavity. However, the adsorption capacity needs to be improved for targeted pollutants. Herein, millimeter-scale hollow vesicles were prepared with a one-step process of sequential stirring and grafting using chitosan, diallyldimethylammonium chloride, and sodium alginate as raw materials with the purpose of efficient removal of anionic dyes from wastewater. The composite vesicles were characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. The hollow vesicles showed the structure of the cationic membrane and the inner cavity, facilitating the dye adsorption. The adsorption capacity for the anionic dye Reactive Black 5 reached 698.1 mg/g, more than twice that of the binary composite vesicles without graft. The adsorption kinetics and isotherm data coincided with the pseudo-second-order and Langmuir models, respectively, and the adsorption mechanism was monolayer chemisorption. Moreover, the vesicles worked well in wide ranges of environment pH, temperature, and co-existing pollutants. They also possessed excellent cyclic regeneration performance, in which 93 % of the initial adsorption capacity was maintained after four cycles. These results indicate that the millimeter-scale hollow vesicles exhibit broad application prospects for wastewater purification.

Effects of montmorillonite on the loading and release of Piper betle L. extract applied for wound dressing based on chitosan/polyvinyl alcohol

In this study, we investigate the influence of montmorillonite (MMT) on the loading and release of Piper betle L. extract (PLE)-a medicinal herb containing active secondary metabolites with antibacterial, antioxidant, and anti-inflammatory effects. MMT (1 %, 3 %, 5 %) was blended into the chitosan/polyvinyl alcohol (CS/PVA) biocomposite film by the solution evaporation method, and then PLE was loaded onto this biocomposite using the immersion method. The tensile strength and the ability to absorb exudates of the CS/PVA film improved with the increase in MMT content. The MMT 3 % film was considered to have the best properties: good mechanical properties with a tensile strength of 27.44 ± 0.27 MPa and elongation at break of 14.57 ± 0.30 %, potential for wound dressing due to its ability to absorb wound exudate (swelling degree 61.70 ± 0.30 %) and a suitable water vapor transmission rate (1999 ± 47 g/m2·d). The presence of MMT (1 %, 3 %, 5 %) in the CS/PVA film led to an increase in the PLE loading efficiency of the films compared to the film without MMT, up to 1.65, 1.73, and 1.87 times, respectively. The MMT 3 % and 5 % films also exhibited a sustained PLE release effect for up to 24 h. MMT increased PLE bioavailability through bioactivity tests: antibacterial activity against both E. coli and S. aureus, antioxidant activity, effective healing of 2nd-degree burn wounds, and biocompatibility with the L929 fibroblasts cell line. The combination of physicochemical properties and biological activities proved that the MMT/PLE drug delivery system based on the CS/PVA biocomposite is promising for wound dressing.

Injectable Hydrogels: A Paradigm Tailored with Design, Characterization, and Multifaceted Approaches

Biomaterials denoting self-healing and versatile structural integrity are highly curious in the biomedicine segment. The injectable and/or printable 3D printing technology is explored in a few decades back, which can alter their dimensions temporarily under shear stress, showing potential healing/recovery tendency with patient-specific intervention toward the development of personalized medicine. Thus, self-healing injectable hydrogels (IHs) are stunning toward developing a paradigm for tissue regeneration. This review comprises the designing of IHs, rheological characterization and stability, several benchmark consequences for self-healing IHs, their translation into tissue regeneration of specific types, applications of IHs in biomedical such as anticancer and immunomodulation, wound healing and tissue/bone regeneration, antimicrobial potentials, drugs, gene and vaccine delivery, ocular delivery, 3D printing, cosmeceuticals, and photothermal therapy as well as in other allied avenues like agriculture, aerospace, electronic/electrical industries, coating approaches, patents associated with therapeutic/nontherapeutic avenues, and numerous futuristic challenges and solutions.

Entrapment of Papain in Chitosan-Polyethylene Glycol Hybrid Nanohydrogels: Presenting a Model for Protein Delivery Systems

In this study, the process of manufacturing nanohydrogels containing papain and how to release it was investigated. Chitosan nanohydrogels and chitosan-polyethylene glycol hybrid nanohydrogels were used to entrapment of papain as a protein model. In order to evaluate and confirm different properties of nanohydrogels such as size, shape, the rate of swelling and flexibility, different methods was used. The maximum amount of papain entrapment was observed in 0.75% concentration of chitosan and 1% concentration of sodium Tripolyphosphate (TPP) as linker. The results of scanning electron microscope (SEM) and X-ray diffraction (XRD) patterns showed that nanohydrogels containing papain on a nano scale are very porous and swollen. Differential scanning calorimetry (DSC) thermograms analysis showed that nanohydrogels have relatively good water absorption capacity. Also, by adding polyethylene glycol to chitosan, the melting temperature of hybrid nanohydrogels decreased and this can be a reason for the formation of flexible structures in these nanohydrogels. In chitosan nanohydrogels, the highest release rate of papain was observed at pH lower than 7 and high temperatures, but by adding polyethylene glycol to the chitosan, in addition to increasing papain release, a proper and continuous release of papain was observed at temperature and pH close to physiological conditions, especially at low ratios of polyethylene glycol. According to the present results, hybrid nanohydrogels can have a good potential in protein delivery systems in terms of structure and release.

Preparation and antitumor study of intelligent injectable hydrogel: Carboxymethyl chitosan-aldehyde gum Arabic composite graphene oxide hydrogel

In this study, we used polyaldehyde gum Arabic (OGA) and carboxymethyl chitosan (CMCS) as a gel matrix to form an injectable self-healing hydrogel by Schiff-base bonding. Further, graphene oxide (GO) was loaded with doxorubicin (DOX) to the hydrogel, which resulted in a CMCS-OGA/GO@DOX hydrogel. We achieved a DOX drug loading capacity of 43.80 ± 1.13 %. Rheological studies showed that GO hydrogels have improved mechanical properties. The in vitro release profile showed pH responsiveness with 88.21 % DOX release at pH 5.5. Biocompatibility studies showed that the hydrogel composition had good cytocompatibility with L929 cells. The 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay showed a cell survival rate of 93.88 % within 48 h. The DOX-loaded hydrogel exhibited higher cell mortality in breast cancer cells (4 T1), with an inhibition rate of 79.4 % at 48 h. Acridine orange/ethidium bromide staining experiments on 4 T1 cells showed that when loaded with the same DOX concentration, the hydrogel significantly reduced the toxic effects on normal cells, whereas it had significant cytotoxic effects on cancer cells. This result indicates that the prepared GO hydrogel drug delivery system can serve as a novel approach for localized breast cancer treatment.

Rheological insights on Carboxymethyl cellulose hydrogels

Hydrogels are copiously studied for tissue engineering, drug delivery, and bone regeneration owing to their water content, mechanical strength, and elastic behaviour. The preparation of stable and mechanically strengthened hydrogels without using toxic crosslinkers and expensive approaches is immensely challenging. In this study, we prepared Carboxymethyl cellulose based hydrogels with different polymer concentration via a less expensive physical crosslinking approach without using any toxic crosslinkers and evaluated their mechanical strength. In this hydrogel system, the carbopol concentration was fixed at 1 wt/v% and the Carboxymethyl cellulose concentration was varied between 1 and 5 wt/v%. In this hydrogel system, Carbopol serves as the crosslinker to bridge Carboxymethyl cellulose polymer through hydrogen bonds. Rheological analysis was employed in assessing the mechanical properties of the prepared hydrogel, in particular, the viscoelastic behaviour of the hydrogels. The viscoelastic nature and mechanical strength of the hydrogels increased with an increase in the Carboxymethyl cellulose polymer concentration. Further, our results suggested that gels with Carboxymethyl cellulose concentration between 3 wt/v % and 4 wt/v % with yield stresses of 58.83 Pa and 81.47 Pa, respectively, are potential candidates for use in transdermal drug delivery. The prepared hydrogels possessed high thermal stability and retained their gel network structure even at 50 °C. These findings are beneficial for biomedical applications in transdermal drug delivery and tissue engineering owing to the biocompatibility, stability, and mechanical strength of the prepared hydrogels.

Effects of carboxymethyl cellulose fiber formations with chitosan incorporation via coating and mixing processes

To date, the utilization of carboxymethyl cellulose (CMC) fibers are only restricted to weak mechanical application such as wound dressing. Physically, CMC has a weak mechanical strength due to the high hydrophilicity trait. However, this flaw was saved by the extensive number of reactive functional groups, allowing this macromolecule to form linkages with chitosan to ensure its versatility. This work successfully fabricated CMC-chitosan fiber via dissolution, crosslinking, dry-jet wet-spinning extrusion, and coagulation processes. Chitosan was constituted with CMC fiber in two approaches, coating, and inclusion at various concentrations. Morphologically, chitosan incorporation has triggered agglomerations and roughness toward CMC fibers (CMCF). Chemically, the interaction between CMC and chitosan was proved through FTIR analysis at peaks 1245 cm-1 (ECH covalent crosslinking), while 3340 cm-1 and 1586 cm-1 were due to ionic and hydrogen bonding. The result from analysis showed that at higher chitosan concentrations, the chitosan-included CMC fiber (CMCF-I) and chitosan-coated CMC fiber (CMFC) were mechanically enhanced (up to 86.77 and 82.72 MPa), thermally more stable (33 % residual mass), and less hydrophilic compared to the plain CMCF. The properties of CMC-chitosan fibers have opened up vast possible applications, especially as a reinforcement in a watery medium such as a hydrogel.

Development and characterization of pH responsive sodium alginate hydrogel containing metal-phenolic network for anthocyanin delivery

Favorable hydrogels can be used as a material to deliver bioactive molecules and improve the stability of bioactive substances, while their safety needs to be improved. In this study, protocatechuic acid (PCA) and Fe3+ were rapidly self-assembled to form a metal-phenolic network under different pH conditions, and then sodium alginate (SA) was added to prepare the SA/PCA/Fe hydrogel without adding other chemical reagents. The structural characteristic of SA/PCA/Fe hydrogel was characterized by infrared spectroscopy, X-ray diffraction analysis and scanning electron microscopy. The results showed that the structures of SA/PCA/Fe hydrogels prepared at different pH values were significantly different. The texture analysis, water-holding measurement and rheological analysis indicated that the SA/PCA/Fe hydrogel showed higher gel strength, water holding capacity and storage modulus. Thermogravimetric analysis illuminated that the SA/PCA/Fe hydrogel enhanced the thermal stability of free anthocyanins through encapsulating anthocyanins. Moreover, in vitro simulated digestion experiment revealed that SA/PCA/Fe hydrogel could control the release of anthocyanins in the simulated gastrointestinal tract. To sum up, this present study might provide a safer and feasible way for the delivery of bioactive substances.

The effect of conductive aligned fibers in an injectable hydrogel on nerve tissue regeneration

Injectable hydrogels are a promising treatment option for nervous system injuries due to the difficulty to replace lost cells and nervous factors but research on injectable conductive hydrogels is limited and these scaffolds have poor electromechanical properties. This study developed a chitosan/beta-glycerophosphate/salt hydrogel and added conductive aligned nanofibers (polycaprolactone/gelatin/single-wall carbon nanotube (SWCNT)) for the first time and inspired by natural nerve tissue to improve their biochemical and biophysical properties. The results showed that the degradation rate of hydrogels is proportional to the regrowth of axons and these hydrogels' mechanical (hydrogels without nanofibers or SWCNTs and hydrogels containing these additions have the same Young's modulus as the brain and spinal cord or peripheral nerves, respectively) and electrical properties, and the interconnective structure of the scaffolds have the ability to support cells.

Immobilization of horseradish peroxidase with zwitterionic polymer material for industrial phenolic removal

Horseradish peroxidase (HRP) is a hemoglobin composed of a single peptide chain that catalyzes the oxidation of various substrates such as phenol and aniline in the presence of hydrogen peroxide via its iron-porphyrin catalytic center. This enzyme is widely used in industrial phenol removal, food additives, biomedicine, and clinical test reagents due to its rapid reaction rate and obvious reaction outcomes. However, the large-scale use of HRP in industrial applications still faces numerous challenges, including activity, stability, and sustainability. This study demonstrates that when peroxidase is immobilized in zwitterionic polymer hydrogels, polycarboxybetaine (PCB) and polysulfobetaine (PSB), the properties of the enzyme are improved. PCB and PSB-embedded HRP exhibit a 6.11 and 1.53 times increase in Kcat/Km value, respectively, compared to the free enzyme. The immobilized enzyme also experiences increased activity over a range of temperatures and better tolerance to extreme pH and organic solvents, including formaldehyde. In addition, immobilized HRP exhibits excellent performance in storage and reproducibility. Remarkably, PCB-HRP still retains 80% of the initial activity after a 6-week storage period and can still attain the initial catalytic level of the free enzyme after six repeated cycles. It also removes 90% of phenol within 12 min, surpassing the current pharmacy on the market. These experimental results indicated that we have successfully designed a set of stable and efficient support substrates for horseradish peroxidase, which enhances its suitability for deployment in industrial applications.

Development of Tofacitinib Loaded pH-Responsive Chitosan/Mucin Based Hydrogel Microparticles: In-Vitro Characterization and Toxicological Screening

Tofacitinib is an antirheumatic drug characterized by a short half-life and poor permeability, which necessitates the development of sustained release formulation with enhanced permeability potential. To achieve this goal, the free radical polymerization technique was employed to develop mucin/chitosan copolymer methacrylic acid (MU-CHI-Co-Poly (MAA))-based hydrogel microparticles. The developed hydrogel microparticles were characterized for EDX, FTIR, DSC, TGA, X-ray diffraction, SEM, drug loading; equilibrium swelling (%), in vitro drug release, sol–gel (%) studies, size and zeta potential, permeation, anti-arthritic activities, and acute oral toxicity studies. FTIR studies revealed the incorporation of the ingredients into the polymeric network, while EDX studies depicted the successful loading of tofacitinib into the network. The thermal analysis confirmed the heat stability of the system. SEM analysis displayed the porous structure of the hydrogels. Gel fraction showed an increasing tendency (74–98%) upon increasing the concentrations of the formulation ingredients. Formulations coated with Eudragit (2% w/w) and sodium lauryl sulfate (1% w/v) showed increased permeability. The formulations equilibrium swelling (%) increased (78–93%) at pH 7.4. Maximum drug loading and release (%) of (55.62–80.52%) and (78.02–90.56%), respectively, were noticed at pH 7.4, where the developed microparticles followed zero-order kinetics with case II transport. Anti-inflammatory studies revealed a significant dose-dependent decrease in paw edema in the rats. Oral toxicity studies confirmed the biocompatibility and non-toxicity of the formulated network. Thus, the developed pH-responsive hydrogel microparticles seem to have the potential to enhance permeability and control the delivery of tofacitinib for the management of rheumatoid arthritis.

Synthesis and Evaluation of Rutin–Hydroxypropyl β-Cyclodextrin Inclusion Complexes Embedded in Xanthan Gum-Based (HPMC-g-AMPS) Hydrogels for Oral Controlled Drug Delivery

Oxidants play a significant role in causing oxidative stress in the body, which contributes to the development of diseases. Rutin—a powerful antioxidant—may be useful in the prevention and treatment of various diseases by scavenging oxidants and reducing oxidative stress. However, low solubility and oral bioavailability have restricted its use. Due to the hydrophobic nature of rutin, it cannot be easily loaded inside hydrogels. Therefore, first rutin inclusion complexes (RIC) with hydroxypropyl-β-cyclodextrin (HP-βCD) were prepared to improve its solubility, followed by incorporation into xanthan gum-based (hydroxypropyl methylcellulose-grafted-2-acrylamido -2-methyl-1-propane sulfonic acid) hydrogels for controlled drug release in order to improve the bioavailability. Rutin inclusion complexes and hydrogels were validated by FTIR, XRD, SEM, TGA, and DSC. The highest swelling ratio and drug release occurred at pH 1.2 (28% swelling ratio and 70% drug release) versus pH 7.4 (22% swelling ratio, 65% drug release) after 48 h. Hydrogels showed high porosity (94%) and biodegradation (9% in 1 week in phosphate buffer saline). Moreover, in vitro antioxidative and antibacterial studies (Staphylococcus aureus, Pseudomonas aeruginosa, and Escherichia coli) confirmed the antioxidative and antibacterial potential of the developed hydrogels.

MOF-implanted poly (acrylamide-co-acrylic acid)/chitosan organic hydrogel for uranium extraction from seawater

In this study, a composite hydrogel with a low swelling ratio, excellent mechanical properties, and good U (VI) adsorption capacity was developed by incorporating a metal-organic framework (MOF) with a poly (acrylamide-co-acrylic acid)/chitosan (P(AM-co-AA)/CS) composite. The CS chain, which contains NH₂, reduces the swelling ratio of the hydrogel to 4.17 after 5 h of immersion in water. The coordinate bond between the MOF and carboxyl group on the surface of P(AM-co-AA)/CS improves the mechanical properties and stability of P(AM-co-AA)/CS. The U(VI) adsorption capacity of P(AM-co-AA)/CS/MOF-808 is 159.56 mg g^-1 at C₀ = 99.47 mg L^-1 and pH = 8.0. The adsorption process is well fitted by the Langmuir isotherm and pseudo-second-order model. The P(AM-co-AA)/CS/MOF-808 also exhibits good repeatability and stability after five adsorption-desorption cycles. The uranium adsorption capacity of the developed adsorbent after one month in natural seawater is 6.2 mg g^-1, and the rate of uranium adsorption on the hydrogel is 0.21 mg g^-1 day^-1.

Physicochemical properties of electrostatically crosslinked carrageenan/chitosan hydrogels and carrageenan/chitosan/Laponite nanocomposite hydrogels

In this work physical carrageenan/chitosan (Car/Chit) hydrogels are prepared by electrostatic complexation between the two oppositely charged polysaccharides. The hydrogels have storage moduli in the order of 5-10 kPa and swelling ratios in the order of 5000-6000 %. At conditions where both polysaccharides are highly charged (pH 5) the swelling ratios are lower than the ones at conditions of lower dissociation i.e., at pH 2 and 7 and the opposite trend is found for the storage modulus. Chit appears to act as a crosslinker for Car as increasing its concentration the swelling ratio decreases and the moduli increase. The hydrogels can incorporate the nanoclay Laponite (Lap) and form hybrid nanocomposites where the intercalation by the two biopolymers leads to exfoliation of the clay nanoplatelets in the presence of both Car and Chit. The composite hydrogels retain the mechanical properties of the Car/Chit hydrogels at the studied pH range (pH 2 to pH 7). This shows the prepared hydrogels can be potentially used as multifunctional biomaterials for drug delivery, tissue engineering and bone regeneration applications.

Green multifunctional PVA composite hydrogel-membrane for the efficient purification of emulsified oil wastewater containing Pb2+ ions

To date, most existing engineering materials have difficulty simultaneously separating oil/water and removing heavy metals from complex oily wastewater. In response to this challenge, a novel multifunctional composite hydrogel membrane (named PVA-CS-LDHs) was fabricated by incorporating chitosan (CS) and nanohydrotalcite (LDHs) into a polyvinyl alcohol (PVA) hydrogel. This material was developed using an easy yet versatile strategy of freezing and salting-out, which can enable the formation of a PVA-CS-LDH hydrogel membrane in one step and endow the PVA-CS-LDHs with high strength, excellent stretchability, favourable shape recoverability, and an ideal 3D microstructure. The PVA-CS-LDH membrane can purify emulsified oil and metal ions simultaneously with a separation efficiency of 99.89 % for emulsified oil and a removal efficiency of 97.44 % for Pb2+ ions. Additionally, the high-efficiency, multifunctional, high-antifouling and eco-friendly properties of the PVA-CS-LDH membrane make it a promising hydrogel material for both emulsified oil separation and heavy metal ion removal. Thus, this material provides critical application potential that can address scientific and technological challenges in complex oily wastewater purification.

A Trilaminar-Thermosensitive Hydrogel Catalytic Reactor Capable of Single/Tandem Catalytic Switchable Ability

The present endeavor is to develop a highly-intelligent catalytic reactor prototype which is able to autonomously adapt to the environment and provides an in-situ double-shift catalytic ability. By seeking inspiration from nature, this objective is achieved by developing a self-adaptive hydrogel catalytic reactor which held a catalytic trilaminar structure capable of reverse thermosensitive properties. With increasing temperatures, the catalytic tri-layers of this catalytic reactor would function in a sequential way (i.e., one negative temperature response layer, one support layer and one positive temperature response layer) and as a result, led to the single-tandem double-shift catalytic ability. This catalytic reactor individually presented single/tandem catalytic process at relatively low temperatures or high temperatures through the cooperative work of the three layers. In this way, this catalytic reactor showed the single-tandem controllable catalytic ability. The novel protocol not only provides a new solution to complicated catalytic processes but also inspires the further application of smart polymers in a broader spectrum of areas.

Application of Nano-Inspired Scaffolds-Based Biopolymer Hydrogel for Bone and Periodontal Tissue Regeneration

This review’s objectives are to provide an overview of the various kinds of biopolymer hydrogels that are currently used for bone tissue and periodontal tissue regeneration, to list the advantages and disadvantages of using them, to assess how well they might be used for nanoscale fabrication and biofunctionalization, and to describe their production processes and processes for functionalization with active biomolecules. They are applied in conjunction with other materials (such as microparticles (MPs) and nanoparticles (NPs)) and other novel techniques to replicate physiological bone generation more faithfully. Enhancing the biocompatibility of hydrogels created from blends of natural and synthetic biopolymers can result in the creation of the best scaffold match to the extracellular matrix (ECM) for bone and periodontal tissue regeneration. Additionally, adding various nanoparticles can increase the scaffold hydrogel stability and provide a number of biological effects. In this review, the research study of polysaccharide hydrogel as a scaffold will be critical in creating valuable materials for effective bone tissue regeneration, with a future impact predicted in repairing bone defects.

Structural characterization and hypolipidemic activity of Gracilaria lemaneiformis polysaccharide and its degradation products

This research aimed to analyze structural characterization and hypolipidemic activity in vitro of G. lemaneiformis polysaccharide (GLP) and its degradation products. The results presented that the content of galacturonic acid declined and glucuronic acid level enhanced, average particle size decreased from 99.9 μm to 25.7 μm, and color brightness of polysaccharide strengthened after degraded by H₂O₂-Vc. There was no significant change in thermal stability of polysaccharide before and after degradation. It was observed in AFM analysis, polysaccharide changed to smaller, delicacy and dispersion after degradation. As seen in FT-IR, H₂O₂-Vc degradation never change the structure of polysaccharide. Polysaccharide and its degradation products showed a significant inhibition effect on pancreatic lipase and cholesterol esterase in a dose-dependent manner, which presented the mixed type of competitive and non-competitive for pancreatic lipase, and non-competitive for cholesterol esterase, respectively. The fluorescence quenching type was static on pancreatic lipase and dynamic on cholesterol esterase.

Synthesis And Evaluation of Polyethylene Glycol-4000-Co-Poly (AMPS) Based Hydrogel Membranes for Controlled Release of Mupirocin for Efficient Wound Healing

BACKGROUND

Chronic wound healing is a major challenge for health care system around the globe. Current study was conducted to develop and characterize chemically cross-linked polyethylene glycol-co-poly (AMPS) hydrogel membranes to enhanced the wound healing efficiency of antibiotic mupirocin (MP).

METHODS

Free radical polymerization technique was used for the development of hydrogel membranes. In aqueous medium, polymer PEG-4000 cross-linked with the monomer 2-acrylamido-2-methylpropane sulfonic acid (AMPS) in the presence of initiators ammonium peroxide sulfate (APS) and sodium hydrogen sulfite (SHS). N, N-Methylenebisacrylamide (MBA) was used as cross-linker in the preparation of hydrogel membranes. Developed membranes were spherical, transparent, and elastic. FTIR, TGA/DSC, and SEM were used to characterize the polymeric system. Swelling behavior, drug loading, and its release pattern at pH of 5.5 and 7.4, irritation study, ex vivo drug permeation, and deposition study was also evaluated.

RESULTS

Formed membranes were spherical, transparent and elastic. The formation of a stable polymeric network was confirmed by structural and thermal analysis. Permeation of the drug its deposition in the skin showed good permeation and retention. No irritancy to the skin was observed.

CONCLUSION

On the basis of results obtained, the present study concluded that it may be an ideal network for the delivery of mupirocin in skin infections.

Sustained delivery of gemcitabine via in situ injectable mussel-inspired hydrogel for local therapy of pancreatic cancer

The issue on pervasively enhanced drug resistance of pancreatic cancer is fundamental to better understanding of gemcitabine-based chemotherapy. Currently available treatment plans containing injectable therapeutics are mainly engineered to improve...

Hydrogels for modified-release drug delivery systems

Hydrogels for the modified-release drug delivery systems is a continuously growing area of interest for the pharmaceutical industry. According to the global market, the use of polymers in this area is projected to reach $31.4 million by 2027. This review discusses the recent advances and perspectives of hydrogel in drug delivery systems for oral, parenteral, nasal, topical, and ophthalmic. The search strategy did in January 2021, and it conducted an extensive database to identify studies published from January 2010 to December 2020.We described the main characteristic of the polymers to obtain an ideal hydrogel for a specific route of administration and the formulations that was a highlight in the literature. It concluded that the hydrogels are a set useful to decrease the number of doses, side effects, promote adhesion of patient and enhances the bioavailability of the drugs improving the safety and efficacy of the treatment.

Exploring the role of chitosan in affecting the adhesive, rheological and antimicrobial properties of carboxymethyl cellulose composite hydrogels

Natural polysaccharide-based hydrogels are promising in food and pharmaceutical applications. In this study, the potential of composite hydrogels prepared by carboxymethyl cellulose (CMC) and chitosan as glue for cigar wrapping applications was firstly studied. The impacts of degree of carboxymethyl substitution (DS) and the ratio of CMC:chitosan on the adhesive performance and rheological behaviors of composite hydrogels have been investigated. And the results indicated that relatively low DS of CMC and relatively low ratio of chitosan might be favorable for the adhesive properties of composite hydrogels. But a higher ratio of chitosan may significantly improve the rheological properties of composite hydrogels and alter their thermal-sensitivity. The impacts of chitosan on the wet ability with tobacco leaf, the morphology and the XRD patterns of composite hydrogels were also observed. The CMC-chitosan composite hydrogel could significantly decrease the total molds on tobacco leaf brought by CMC, and therefore may show great potential to improve the quality of cigar during long-term storage. All the information in this study is new, which could be useful for exploring the application of CMC-chitosan composite hydrogel in food, pharmaceutical, even other fields.

Facile transformation of carboxymethyl cellulose beads into hollow composites for dye adsorption

Novel millimeter hollow microspheres were fabricated from carboxymethyl cellulose microspheres and polyethyleneimine using glutaraldehyde as a crosslinking agent. The hollow microspheres prepared with different polyethyleneimine usages and different polyethyleneimine treatment time were investigated deeply and characterized via SEM-EDX, FT-IR, and BET surface area analysis. It was shown that polyethyleneimine could break the coordination bonds between the carboxyl and Al (III) in carboxymethyl cellulose microspheres, leading to the formation of hollow structures. Most importantly, the usage and treatment time of polyethyleneimine can distinctly tailor the structure of the carboxymethyl cellulose microspheres, resulting in the formation of different hollow microspheres with varied shell thickness and size. Most importantly, we found that the prepared hollow microspheres have excellent adsorption performance toward targeted methyl blue under testing conditions. By virtue of the large accessible amount of -NH₂ groups and its unique hollow structure, this type of millimeter hollow microspheres have broad application prospects in the treatment of emerging contaminants in wastewater.

Tunable and tough porous chitosan/β-cyclodextrin/tannic acid biocomposite membrane with mechanic, antioxidant, and antimicrobial properties

Herein, tannic acid (TA)-reinforced chitosan (CHS)/β-cyclodextrin (β-CD) biocomposite membranes were prepared by TA solution incubating treatment. The functional groups, crystal structure, and morphological characterizations of the prepared biocomposite membranes were investigated using various methods. The biocomposite membranes were investigated in terms of their wettability, porosity, swelling degree, and water uptake. In vitro antioxidant investigation was carried out through DPPH assay. Moreover, the prepared biocomposite membranes were evaluated for their antimicrobial ability against three different microbial species. The introduction of TA effectively improved the swelling behavior, mechanical strength, and porosity of the biocomposite membranes. TA increased the tensile strength from 0.7 ± 0.2 MPa to a maximum of 2.2 ± 0.6 MPa and elongation at break from 26.9 ± 0.7% to a maximum of 36.7 ± 3.5%. The biocomposite membranes showed an initial burst release of TA (~40%) within 6 h, followed by a gradual release of 100% by 18 h. Furthermore, the introduction of TA into the biocomposite membranes further improved the antimicrobial activities against both bacteria and yeast, as well as the in vitro antioxidant potential. As a consequence, the prepared biocomposite membranes could potentially be used as scaffold in broaden biomedical fields due to their adaptable structure, porosity, greatly antioxidant, and antimicrobial activity.

Recent progress in the preparation, chemical interactions and applications of biocompatible polysaccharide-protein nanogel carriers

Nanogel carriers are rapidly emerged as a major delivery strategy in the fields of food, biology and medicine for small particle size, excellent solubility, high loading, and controlled release. Natural polysaccharides and proteins are selected for the preparation of biocompatible, biodegradable, low toxic, and less immunogenic nanogels. Different polysaccharides and proteins form complex nanogels through different interaction forces (e.g., electrostatic interaction and hydrophobic interaction). The present review pursues three aims: 1) to introduce several well-known dietary polysaccharides (chitosan, dextran and alginate) and proteins (whey protein and lysozyme); 2) to discuss the types, preparation methods, chemical interactions and properties of various biocompatible complex carriers; 3) to present the application and prospect of polysaccharide-protein complex in bioactive ingredient delivery, nutrient encapsulation and flavor protection. We expect that the integration with nano-intelligent technology will improve the functional ingredient loading, recognition specificity and controlled release capabilities of polysaccharide-protein nanocomposites to generate new intelligent nanogels in the field of food industry in the future.

5-Fluorouracil Encapsulated Chitosan-Cellulose Fiber Bionanocomposites: Synthesis, Characterization and In Vitro Analysis towards Colorectal Cancer Cells

Cellulose and chitosan with remarkable biocompatibility and sophisticated physiochemical characteristics can be a new dawn to the advanced drug nano-carriers in cancer treatment. This study aims to synthesize layer-by-layer bionanocomposites from chitosan and rice straw cellulose encapsulated 5-Fluorouracil (CS-CF/5FU BNCs) using the ionic gelation method and the sodium tripolyphosphate (TPP) cross-linker. Data from X-ray and Fourier-transform infrared spectroscopy showed successful preparation of CS-CF/5FU BNCs. Based on images of scanning electron microscopy, 48.73 ± 1.52 nm was estimated for an average size of the bionanocomposites as spherical chitosan nanoparticles mostly coated rod-shaped cellulose reinforcement. 5-Fluorouracil indicated an increase in thermal stability after its encapsulation in the bionanocomposites. The drug encapsulation efficiency was found to be 86 ± 2.75%. CS-CF/5FU BNCs triggered higher drug release in a media simulating the colorectal fluid with pH 7.4 (76.82 ± 1.29%) than the gastric fluid with pH 1.2 (42.37 ± 0.43%). In in vitro cytotoxicity assays, cellulose fibers, chitosan nanoparticles and the bionanocomposites indicated biocompatibility towards CCD112 normal cells. Most promisingly, CS-CF/5FU BNCs at 250 µg/mL concentration eliminated 56.42 ± 0.41% of HCT116 cancer cells and only 8.16 ± 2.11% of CCD112 normal cells. Therefore, this study demonstrates that CS-CF/5FU BNCs can be considered as an eco-friendly and innovative nanodrug candidate for potential colorectal cancer treatment.

β-cyclodextrin chitosan-based hydrogels with tunable pH-responsive properties for controlled release of acyclovir: design, characterization, safety, and pharmacokinetic evaluation

In this work, series of pH-responsive hydrogels (FMA1–FMA9) were synthesized, characterized, and evaluated as potential carrier for oral delivery of an antiviral drug, acyclovir (ACV). Different proportions of β-cyclodextrin (β-CD), chitosan (CS), methacrylic acid (MAA) and N′ N′-methylenebis-acrylamide (MBA) were used to fabricate hydrogels via free radical polymerization technique. Fourier transform infrared spectroscopy confirmed fabrication of new polymeric network, with successful incorporation of ACV. Scanning electron microscopy (SEM) indicated presence of slightly porous structure. Thermal analysis indicated enhanced thermal stability of polymeric network. Swelling studies were carried out at 37 °C in simulated gastric and intestinal fluids. The drug release data was found best fit to zero-order kinetics. The preliminary investigation of developed hydrogels showed a pH-dependent swelling behavior and drug release pattern. Acute oral toxicity study indicated no significant changes in behavioral, clinical, or histopathological parameters of Wistar rats. Pharmacokinetic study indicated that developed hydrogels caused a significant increase in oral bioavailability of ACV in rabbit plasma as compared to oral suspension when both were administered at a single oral dose of 20 mg kg⁻¹ bodyweight. Hence, developed hydrogel formulation could be used as potential candidate for controlled drug delivery of an antiviral drug acyclovir.

Marine polysaccharide-based composite hydrogels containing fucoidan: Preparation, physicochemical characterization, and biocompatible evaluation

Marine polysaccharide-based hydrogels have drawn much attention for diversified biomedical applications owing to their excellent (bio)physicochemical properties. In the present work, a series of marine polysaccharide-based hydrogels composed of chitosan, alginate, or fucoidan are prepared via a facile chemical cross-linking approach in an alkali/urea aqueous system. The prepared hydrogels possess tunable microporous architecture, swelling, and biodegradable properties by changing the components and proportions of marine polysaccharides. Importantly, the developed hydrogels are mechanically robust and the maximum compressive stress is up to 28.37 ± 4.63 kPa. Furthermore, the composite hydrogels exhibit excellent cytocompatibility, blood compatibility, and histocompatibility. When implanted subcutaneously in rats, the hydrogels containing fucoidan inhibit the inflammatory response of surrounding tissue. Thus, the designed composite hydrogels are promising bio-scaffolds in biomedical applications.

Preparation and Characterization of Hydroxyapatite Coating on AZ31 Magnesium Alloy Induced by Carboxymethyl Cellulose-Dopamine

Magnesium and its alloys have become potential implant materials in the future because of light weight, mechanical properties similar to natural bone, good biocompatibility, and degradability in physiological environment. However, due to the rapid corrosion and degradation of magnesium alloys in vivo, especially in the environment containing chloride ions, the application of magnesium alloys as implant materials has been limited. Therefore, improving the corrosion resistance of magnesium alloy and ensuring good biocompatibility is the main focus of the current research. In this study, hydroxyapatite coating was prepared on magnesium alloy surface using carboxymethyl cellulose-dopamine hydrogel as inducer to improve corrosion resistance and biocompatibility. Surface characterization techniques (scanning electron microscopy, Fourier-transformed infrared spectroscopy, energy dispersive X-ray spectroscopy- and X-ray diffraction) confirmed the formation of hydroxyapatite on the surface of AZ31 alloy. Corrosion resistance tests have proved the protective effect of Carboxymethyl cellulose-Dopamine/hydroxyapatite (CMC-DA/HA) coating on the surface of AZ31 alloy. According to MC3T3-E1 cell viability and Live/Dead staining, the coating also showed good biocompatibility. The results will provide new ideas for the biological application of magnesium alloys.

Zero Valent Iron Nanoparticle-Loaded Nanobentonite Intercalated Carboxymethyl Chitosan for Efficient Removal of Both Anionic and Cationic Dyes

A zero valent iron-loaded nano-bentonite intercalated carboxymethyl chitosan (nZVI@nBent-CMC) composite was fabricated and characterized by FT-IR, TEM, TEM-EDX, XRD, BET surface area, and zeta potential measurements. The as-fabricated nZVI@nBent-CMC composite exhibited excellent removal efficiency for both anionic Congo red (CR) dye and cationic crystal violet (CV) dye. The maximum uptake capacities of CR and CV onto the nZVI@nBent-CMC composite were found to be 884.95 and 505.05 mg/g, respectively. The adsorption process of both dyes well fitted with the Langmuir isotherm model and pseudo-second order kinetic model. Thermodynamic data clarified that the adsorptions of both CR and CV onto the nZVI@nBent-CMC composite are spontaneous processes. Moreover, the adsorption of CR onto the nZVI@nBent-CMC composite was found to be an exothermic process while that of CV is an endothermic process. The nZVI@nBent-CMC composite also exhibited excellent reusability for both studied dyes without noticeable loss in the removal efficiency, suggesting its validity to remove both anionic and cationic dyes from wastewater.

Injectable Hydrogels: From Laboratory to Industrialization

The transfer of some innovative technologies from the laboratory to industrial scale is many times not taken into account in the design and development of some functional materials such as hydrogels to be applied in the biomedical field. There is a lack of knowledge in the scientific field where many aspects of scaling to an industrial process are ignored, and products cannot reach the market. Injectable hydrogels are a good example that we have used in our research to show the different steps needed to follow to get a product in the market based on them. From synthesis and process validation to characterization techniques used and assays performed to ensure the safety and efficacy of the product, following regulation, several well-defined protocols must be adopted. Therefore, this paper summarized all these aspects due to the lack of knowledge that exists about the industrialization of injectable products with the great importance that it entails, and it is intended to serve as a guide on this area to non-initiated scientists. More concretely, in this work, the characteristics and requirements for the development of injectable hydrogels from the laboratory to industrial scale is presented in terms of (i) synthesis techniques employed to obtain injectable hydrogels with tunable desired properties, (ii) the most common characterization techniques to characterize hydrogels, and (iii) the necessary safety and efficacy assays and protocols to industrialize and commercialize injectable hydrogels from the regulatory point of view. Finally, this review also mentioned and explained a real example of the development of a natural hyaluronic acid hydrogel that reached the market as an injectable product.