ZnO nanorod-chitosan composite coatings with enhanced antifouling properties

Antifouling activity of PEGylated chitosan coatings: Impacts of the side chain length and encapsulated ZnO/Ag nanoparticles

PEGylation is regarded as a common antifouling strategy and the effect is normally linked with surface hydrophilicity of the coatings. Herein, the biopolymer chitosan (CS) was grafted by polyethylene glycol (PEG) of different chain lengths (molecular weight 200, 4 k and 100 k Da) to verify if the hydrophilicity of CS-PEG coatings is crucial in determining antifouling activities and if PEG chain length influences biofouling in marine environment. Properties of copolymers such as melting points and crystallinity are affected by grafting PEG. The water contact angle (WCA) of CS-PEG coatings increases with the chain length of grafted PEG, from 27° to 58°. Photocatalyst of zinc oxide-silver (ZnO/Ag) was also studied and its embedment (2 % to CS-PEG) renders the surface of CS-PEG coatings more hydrophobic with WCA increased from 52° to 86°. Antibacterial, anti-diatom, and anti-biofilm activities of the coatings were evaluated in natural sea water. The bacterial density on CS-PEG coatings was dramatically reduced to 4 × 104 compared to the control of 7 × 104 ind/mm2, and further to 2 × 104 for CS-PEG-ZnO/Ag coatings. CS-PEG coatings also strongly inhibit diatoms (120-200 ind/mm2), but the inclusion of ZnO/Ag did not obviously enhance such effect (50-150 ind/mm2). The findings provide useful insights for designing polymer-based antifouling coatings.

Enhancing post-harvest quality of tomato fruits with chitosan oligosaccharide-zinc oxide nanocomposites: A study on biocompatibility, quality improvement, and carotenoid enhancement

In this study, a new composite with combination of chitosan oligosaccharide (COS) and zinc oxide nanoparticles (ZnO NPs), termed Chitosan Oligosaccharide-Zinc Oxide Nanocomposites (COS-ZnO NC), was designed to enhance the quality of tomato fruits during postharvest storage. SEM analysis showed a uniform distribution of COS-ZnO NC films on tomato surfaces, indicating high biocompatibility, while the FTIR spectrum confirmed the interaction of COS and ZnO NPs via hydrogen bonds. The COS-ZnO NC exerts positive effects on post-harvest quality of tomato fruits, including significantly reduced water loss, fewer skin wrinkles, increased sugar-acid ratio, and enhanced vitamin C and carotenoids accumulation. Furthermore, COS-ZnO NC induces transcription of carotenoid biosynthesis genes and promotes carotenoids storage in the chromoplast. These results suggest that the COS-ZnO NC film can significantly improve the quality traits of tomato fruits, and therefore is potential in post-harvest storage of tomato fruits.

Enhanced surface antimicrobial, biocompatible and mechanical properties of 3D printed titanium alloys by electrophoretic deposition of chitosan/ZnO

In this study, to address the susceptibility of 3D-printed titanium implants to bacterial infection, we propose to form a chitosan/ZnO composite coating by electrophoretic deposition to enhance its antimicrobial, biocompatible, and mechanical properties. The surface morphology of the composite coating is relatively flat, showing good hydrophilicity and coating adhesion, and the corrosion current density is significantly lower than that of the untreated titanium alloy. According to the results of the study, the composite coatings containing more than 0.1 g of ZnO (Z2, Z3, Z4 groups) showed excellent antibacterial effects against Staphylococcus aureus and Escherichia coli, with antibacterial rates of more than 95 %, and the medium-concentration ZnO coatings (Z2 group) showed good cellular activity, with cell viability rates of more than 80 %. In contrast, the high-concentration ZnO coatings (Z3, Z4 groups) showed a certain degree of cytotoxicity. The inherent film-forming property of the composite coating enabled the cells to adhere well to the coating surface. It was found through SBF body fluid immersion that Zn²⁺ can increase the rate of hydroxyapatite precipitation and enhance bioactivity. These results emphasize the importance of precise control of the ZnO content in the improved antimicrobial and biocompatible chitosan-ZnO composite coatings to ensure excellent antimicrobial properties and necessary biocompatibility.

Nanomaterial grafted polymorphous activated carbon cloth surface for antibacterial, capacitive deionization and oil spill cleaning applications

This work reports the development of multifunctional or polymorphous surfaces using zinc oxide (ZnO) nanorods, silica (SiO2), and fluoropolymer functionalization in a sequential process. Firstly, zinc oxide nanorods were grown on activated carbon cloth (ACC) using a simple low-temperature synthesis process. ZnO nanorods-coated ACC substrate was applied to investigate the antimicrobial properties, and the results showed inhibition of 50% for Escherichia coli (E.coli) and 55% for Bacillus subtilis (B.subtilis) over 48 h of incubation time. Subsequent in-situ modification of silica nanoparticles like layer on ZnO nanorods-coated ACC surface was developed and used as an electrode for brackish water desalination in a capacitive deionization system. ZnO-SiO2 modified ACC surface enhanced the desalination efficiency by 1.6 times, the salt removal rate (SRR) by threefold, and the durability (fouling prevention) for long-term usage compared to pristine ACC. Further modification of the ZnO-SiO2-ACC surface using fluoropolymer rendered the surface superhydrophobic and oleophilic. Vegetable (1.4 g/g) and crude oil (1.6 g/g) adsorption capacities were achieved for modified surface which was 70% enhancement compared with pristine ACC. The dynamic oil spill adsorption test exhibited the complete removal of oil spills on water surfaces within a few seconds, suggesting a potential application in oil spill cleaning.

Investigation of the Release Rate of Biocide and Corrosion Resistance of Vinyl-, Acrylic-, and Epoxy-Based Antifouling Paints on Steel in Marine Infrastructures

This study comprehensively assesses the release rate of biocides, corrosion effects related to antifouling, and the physical properties of different paint types. Tests were conducted to measure thickness, viscosity, hardness, bending, adhesion, gloss, impact resistance, abrasion resistance, scratch resistance, polarization, and salt spray. The paints evaluated include resin-based, acrylic-based, epoxy-based, and vinyl-based formulations. The study investigates the influence of biocide content, biocide particle size, and immersion time on release rate using a lab-scale setup. Results showed that acrylic-based paints had a higher biocide release rate due to faster hydrolysis, while smaller biocide particle sizes led to higher release rates in resin-based paints. Optimal total biocide contents were determined to be 30% for acrylic-based, 60% for epoxy-based, and 50% for vinyl-based paints. Antifouling corrosion analysis demonstrated that sample with an optimal release rate effectively prevent algae growth and fouling. Acrylic-based paint with 30 wt.% biocide content exhibited superior adhesion with a dolly separation force of 4.12 MPa. Evaluating the impact of synthesized polyaniline on 30 wt.% epoxy-based paint, a sample coated with 10 wt.% polyaniline represented a low corrosion rate of 0.35 µm/year and a high impedance value of approximately 37,000 Ohm·cm-2.

Prevention of marine biofouling in the aquaculture industry by a coating based on polydimethylsiloxane-chitosan and sodium polyacrylate

In this study, a series of novel hydrophobic/hydrophilic hybrid (HHH) coatings with the feature of preventing the fouling phenomenon was fabricated based on polydimethylsiloxane (PDMS), as matrix and two hydrophilic polymers: chitosan and sodium polyacrylate, as dispersed phases. Antibacterial activity, pseudo-barnacle adhesion strength, surface free energy, water contact angle, and water absorption were performed for all samples. Evaluating field immersion of the samples was performed in the natural seawater. The results showed that the dispersed phase containing PDMS coatings showed simultaneously both of antibacterial activity and foul release behavior. Among the samples, the PCs4 coating containing 4 wt% Cs indicated the lowest pseudo barnacle adhesion strength (0.04 MPa), the lowest surface free energy (18.94 mN/m), the highest water contact angle (116.05°), and the percentage of fouling organisms 9.8 % after 30 days immersion. The HHH coatings can be considered as novel eco-friendly antifouling/foul release coatings for aquaculture applications.

Preparation of nanocomposite based on chitosan-PDCOEMA containing biosynthesized ZnO: Biological and thermal characterization

In this study, poly(2-(3,5-dichloroanilino)-2-oxoethyl 2-methylprop-2-enoate) (PDCOEMA), a new synthetic polymer based on methacrylate, was synthesized and characterized. The blend of PDCOEMA with chitosan (CS) was prepared by the hydrothermal method and the DSC technique confirmed its formation. It was observed that PDCOEMA increased the thermal stability and glass transition temperature (Tg) of CS. The Tg value of the PDCOEMA-CS blend was increased at about 7 °C with the highest ZnO NPs contribution rate. PDCOEMA-CS/ZnO nanocomposites were prepared by adding ZnO NPs produced by biosynthesis at different weight ratios to the PDCOEMA-CS blend by hydrothermal method. When the thermal stability of nanocomposites determined by TGA was examined, it was observed that it increased significantly compared to CS. While the initial decomposition temperature of CS was 270 °C, this value increased to 293 °C after blending with DCOEMA, and to 317 °C with the addition of 7 % ZnO NPs. Antimicrobial, anticancer, cytotoxic, antioxidant, and wound healing properties of PDCOEMA, CS, PDCOEMA-CS blend, and nanocomposites were determined. According to the obtained results, it was observed that nanocomposites containing 5 % and 7 % ZnO NPs showed good anticancer activity against A549 cells at a dose of 10 μg/mL. The results show that the produced nanocomposites can contribute to developing CS-based materials.

Assessment of the Antibiofilm Performance of Chitosan-Based Surfaces in Marine Environments

Marine biofouling is a natural process often associated with biofilm formation on submerged surfaces, creating a massive economic and ecological burden. Although several antifouling paints have been used to prevent biofouling, growing ecological concerns emphasize the need to develop new and environmentally friendly antifouling approaches such as bio-based coatings. Chitosan (CS) is a natural polymer that has been widely used due to its outstanding biological properties, including non-toxicity and antimicrobial activity. This work aims to produce and characterize poly (lactic acid) (PLA)-CS surfaces with CS of different molecular weight (Mw) at different concentrations for application in marine paints. Loligo opalescens pens, a waste from the fishery industry, were used as a CS source. The antimicrobial activity of the CS and CS-functionalized surfaces was assessed against Cobetia marina, a model proteobacterium for marine biofouling. Results demonstrate that CS targets the bacterial cell membrane, and PLA-CS surfaces were able to reduce the number of culturable cells up to 68% compared to control, with this activity dependent on CS Mw. The antifouling performance was corroborated by Optical Coherence Tomography since PLA-CS surfaces reduced the biofilm thickness by up to 36%, as well as the percentage and size of biofilm empty spaces. Overall, CS coatings showed to be a promising approach to reducing biofouling in marine environments mimicked in this work, contributing to the valorization of fishing waste and encouraging further research on this topic.

Antifouling performance of in situ synthesized chitosan-zinc oxide hydrogel film against alga M. aeruginosa

The undesirable settlement and growth of microalgae on submerged installations is a universal problem in water environment. Soft hydrogels are promising fouling-resistant materials due to the inherent surface properties. Herein, a kind of chitosan hydrogels with increasing zinc oxide (ZnO) mineral phase content were prepared by in situ sol-gel and solvent casting method, to prevent growth of algae Microcystis. aeruginosa. Incorporation with ZnO mineral phase improved mechanical property, water absorption, and stability of the obtained chitosan-zinc oxide (CS@ZnO) hydrogel films in Zn dose-dependent manner. The highest strength and growth inhibition (63.45 ± 8.93%) were observed by CS@ZnO-1.5 hydrogel films with the concentrations of 1.5% precursor in comparison with other hydrogel films. During this process, algal cell membrane was slightly damaged (24.5 ± 1.57%) and accompanied by significantly synthesis inhibition such as chlorophyll a (55.22 ± 2.72%) and total soluble protein (42.97 ± 1.66%). To sum up, synthesis inhibition of algal cell is the main mechanism of CS@ZnO hydrogel films inhibiting algal growth, which has the potential in antibiofouling application.

Functional nanomaterials, synergisms, and biomimicry for environmentally benign marine antifouling technology

Marine biofouling remains one of the key challenges for maritime industries, both for seafaring and stationary structures. Currently used biocide-based approaches suffer from significant drawbacks, coming at a significant cost to the environment into which the biocides are released, whereas novel environmentally friendly approaches are often difficult to translate from lab bench to commercial scale. In this article, current biocide-based strategies and their adverse environmental effects are briefly outlined, showing significant gaps that could be addressed through advanced materials engineering. Current research towards the use of natural antifouling products and strategies based on physio-chemical properties is then reviewed, focusing on the recent progress and promising novel developments in the field of environmentally benign marine antifouling technologies based on advanced nanocomposites, synergistic effects and biomimetic approaches are discussed and their benefits and potential drawbacks are compared to existing techniques.

Nanocoating Is a New Way for Biofouling Prevention

Biofouling is a major concern to the maritime industry. Biofouling increases fuel consumption, accelerates corrosion, clogs membranes and pipes, and reduces the buoyancy of marine installations, such as ships, platforms, and nets. While traditionally marine installations are protected by toxic biocidal coatings, due to recent environmental concerns and legislation, novel nanomaterial-based anti-fouling coatings are being developed. Hybrid nanocomposites of organic-inorganic materials give a possibility to combine the characteristics of both groups of material generating opportunities to prevent biofouling. The development of bio-inspired surface designs, progress in polymer science and advances in nanotechnology is significantly contributing to the development of eco-friendly marine coatings containing photocatalytic nanomaterials. The review mainly discusses photocatalysis, antifouling activity, and formulation of coatings using metal and metal oxide nanomaterials (nanoparticles, nanowires, nanorods). Additionally, applications of nanocomposite coatings for inhibition of micro- and macro-fouling in marine environments are reviewed.

Preparation of a superhydrophilic SiO2 nanoparticles coated chitosan-sodium phytate film by a simple ethanol soaking process

The development of environmentally friendly and transparent superhydrophilic food packaging materials is essential in our daily lives. The objective of this study was to develop a simple method of preparing a superhydrophilic, transparent, and biodegradable composite film. The composite film was obtained by soaking a chitosan-sodium phytate film in an ethanol solution of SiO₂ nanoparticles. The results showed that when the chitosan-sodium phytate film was coated with SiO₂ nanoparticles that were dissolved in 75% ethanol, its water contact angle (WCA) was reduced from 100° to 3°, and the film surface was changed from a hydrophobic to a superhydrophilic. Furthermore, the oxygen transmission rate (OTR) was significantly reduced, and the mechanical properties of the film were improved. The method is easy to carry out and can be used for the potential production of superhydrophilic materials.

Constructing three-dimensional network C, O Co-doped nitrogen-deficient carbon nitride regulated by acrylic fluoroboron overall marine antifouling

To deal with unwanted biofouling adsorption, which impacts the economy and the environment, significant research has been devoted to composite systems involving a photocatalyst combined with self-renewal resin to provide synergistic antifouling. Here, photocatalyst based on three-dimensional (3D) network of carbon-oxygen-doped nitrogen-deficient carbon nitride and acrylic fluoroboron polymer as a system was successfully synthesized. 3D networks carbon nitride with carbon-oxygen dopants and nitrogen defects were prepared as skeletons, which effectively support and regulate the hydrolysis rate of the polymer. These composite systems exhibits excellent diatom anti-adhesion performance and high antibacterial rates for Escherichia coli and Staphylococcus aureus of up to 91.87% and 88.52%, respectively. In addition, self-cleaning function of the composite system are proved by and higher efficiency of chemical oxygen demand (COD) removal owing to efficient charge-carrier separation and transfer within the 3D network carbon nitride network. The great potential applications of this strategy demonstrated in marine engineering in the future.

Chitosan/boron nitride nanobiocomposite films with improved properties for active food packaging applications

Chitosan (CS)/boron nitride nanoplatelet (BNNP) nanobiocomposite films were successfully prepared. Morphological results showed good dispersion of BNNPs in the CS matrix. After loading with BNNPs, water solubility (WS) and moisture absorption of the CS film decreased. The WS decreased from 41.2 to 27.8% at 7 wt% BNNP loading. Additionally, water vapor permeation decreased from 4.2 × 10^-11 for pure CS film to 2.9 × 10^-11 g m^-1s^-1Pa^-1 at 7 wt% BNNP inclusion. The oxygen permeability of CS film decreased by up to 84% at 7 wt% BNNP loading. The composites showed better sodium hydroxide resistance compared with pure CS. Thermal stability of the composites was higher than the pure CS, up to 35 °C increase at 7 wt% BNNP loading. The addition of 5 wt% BNNPs improved Young's modulus by up to 45% compared with pure CS film. Cytotoxicity of the films decreased after loading with BNNPs.

A comprehensive survey upon diverse and prolific applications of chitosan-based catalytic systems in one-pot multi-component synthesis of heterocyclic rings

Heterocyclic compounds are among the most prestigious and valuable chemical molecules with diverse and magnificent applications in various sciences. Due to the remarkable and numerous properties of the heterocyclic frameworks, the development of efficient and convenient synthetic methods for the preparation of such outstanding compounds is of great importance. Undoubtedly, catalysis has a conspicuous role in modern chemical synthesis and green chemistry. Therefore, when designing a chemical reaction, choosing and or preparing powerful and environmentally benign simple catalysts or complicated catalytic systems for an acceleration of the chemical reaction is a pivotal part of work for synthetic chemists. Chitosan, as a biocompatible and biodegradable pseudo-natural polysaccharide is one of the excellent choices for the preparation of suitable catalytic systems due to its unique properties. In this review paper, every effort has been made to cover all research articles in the field of one-pot synthesis of heterocyclic frameworks in the presence of chitosan-based catalytic systems, which were published roughly by the first quarter of 2020. It is hoped that this review paper can be a little help to synthetic scientists, methodologists, and catalyst designers, both on the laboratory and industrial scales.

Hierarchically hybrid biocoatings on Ti implants for enhanced antibacterial activity and osteogenesis

Titanium (Ti) is widely applied as bone-anchoring implants in dental and orthopedic applications owing to its superior mechanical characteristics, high corrosion resistance, and excellent biocompatibility. Nevertheless, Ti-based implants with the deficiencies of insufficient osteoinduction and associated infections can result in implant failure, which significantly limits its applications in some cases. In this work, hierarchically hybrid biocoatings on Ti implants are developed by gradual incorporation of polydopamine (PDA), ZnO nanoparticles (nZnO), and chitosan (CS)/nanocrystal hydroxyapatite (nHA) via oxidative self-polymerization, nanoparticle deposition, solvent casting and evaporation methods for enhancing their antibacterial activity and osteogenesis. The modification of PDA on porous reticular Ti substrates greatly reduces the surface roughness, wettability, protein adsorption, and provides high adhesion to the deposited nZnO. Further, incorporating nZnO on PDA-coated Ti surfaces affects the surface structure and wettability, significantly inhibits the growth of both Staphylococcus aureus and Escherichia coli. Moreover, the CS/nHA-doped coating on the nZnO-modified Ti surfaces remarkably improves cytocompatibility and enhances the osteogenic differentiation of MC3T3-E1 cells by upregulating the protein expression of alkaline phosphatase. This work offers a promising alternative for developing Ti implants with long-lifetime bioactivity to achieve strong antibacterial ability and enhanced bone formation for potential dental/orthopedic applications.