Reduced graphene oxide/cellulose nanocrystal composite films with high specific capacitance and tensile strength

CoS2/carbon network flexible film with Co-N bond/π-π interaction enables superior mechanical properties and high-rate sodium ion storage

Flexible electrodes based on conversion-type materials have potential applications in low-cost and high-performance flexible sodium-ion batteries (FSIBs), owing to their high theoretical capacity and appropriate sodiation potential. However, they suffer from flexible electrodes with poor mechanical properties and sluggish reaction kinetics. In this study, freestanding CoS2 nanoparticles coupled with graphene oxides and carbon nanotubes (CoS2/GO/CNTs) flexible films with robust and interconnected architectures were successfully synthesized. CoS2/GO/CNTs flexible film displays high electronic conductivity and superior mechanical properties (average tensile strength of 21.27 MPa and average toughness of 393.18 KJ m-3) owing to the defect bridge for electron transfer and the formation of the π-π interactions between CNTs and GO. In addition, the close contact between the CoS2 nanoparticles and carbon networks enabled by the Co-N chemical bond prevents the self-aggregation of the CoS2 nanoparticles. As a result, the CoS2/GO/CNTs flexible film delivered superior rate capability (213.5 mAh g-1 at 6 A g-1, better than most reported flexible anode) and long-term cycling stability. Moreover, the conversion reaction that occurred in the CoS2/GO/CNTs flexible film exhibited pseudocapacitive behavior. This study provides meaningful insights into the development of flexible electrodes with superior mechanical properties and electrochemical performance for energy storage.

Hydrostability, mechanical resilience, and biodegradability of paper straws fabricated through lignin-based polyurethane and chitosan binary emulsion bonding

This study focuses on enhancing the strength and water stability of paper straws through a novel approach involving a binary emulsion of lignin-based polyurethane and chitosan. Kraft lignin serves as the raw material for synthesizing a blocked waterborne polyurethane, subsequently combined with carboxylated chitosan to form a stable binary emulsion. The resulting emulsion, exhibiting remarkable stability over at least 6 months, is applied to the base paper. Following emulsion application, the paper undergoes torrefaction at 155 °C. This process deblocks isocyanate groups, enabling their reaction with hydroxyl groups on chitosan and fibers, ultimately forming ester bonds. This reaction significantly improves the mechanical strength and hydrophobicity of paper straws. The composite paper straws demonstrate exceptional mechanical properties, including a tensile strength of 47.21 MPa, Young's modulus of 4.33 GPa, and flexural strength of 32.38 MPa. Notably, its water stability is greatly enhanced, with a wet tensile strength of 40.66 MPa, surpassing commercial paper straws by 8 folds. Furthermore, the composite straw achieves complete biodegradability within 120 days, outperforming conventional paper straws in terms of environmental impact. This innovative solution presents a promising and sustainable alternative to plastic straws, addressing the urgent need for eco-friendly products.

On rheological properties of disc-shaped cellulose nanocrystals

The rheological properties of a substance depend greatly on its morphology, and rod-shaped cellulose nanocrystals (RCNCs) and cellulose nanofibrils (CNFs) have been extensively studied for their rheological properties. Nevertheless, the rheological properties of disc-shaped cellulose nanocrystals (DCNCs) with crystalline allomorph II derived from mercerized cellulose remain unknown yet. This work investigated the DCNCs' rheological properties in depth using steady-shear and oscillation measurements. At the same concentration, DCNC's suspension viscosity is lower than that of RCNC; RCNC has an instinct viscosity of 258.2, while DCNC has 187.9. Comparing RCNC suspensions with cellulose nanorods, DCNC has a lower aspect ratio and exhibits a distinct steady shear behavior. Under polarized film, DCNC suspension cannot self-assemble into chiral or liquid crystal phases, and with increasing concentrations, the system transitions from an isotropic phase to a gel phase. Oscillation sweeps demonstrate that the gel transition occurs at 7 %-8 %. Based on thixotropic recovery sweep outcomes, the high-stress oscillations enhance the network structure of DCNC suspensions, which is significantly different from that of RCNC suspensions. Results demonstrate the unique properties of DCNC, highlighting its application as a rheological modifier.

Silver nanoparticles coated cellulose-based flexible membrane with excellent UV resistance, high infrared reflection and water resistance for personal thermal management

Designing of a green and multifunctionally integrated cellulose-based flexible wearable material with personal thermoregulation, water and ultraviolet (UV) resistance is essential for the development of personal thermal management and smart textiles. Herein, a hydrophobic silver nanoparticles cellulose-based membrane (H-AgNPs/CEPCM) was prepared through simple solution blending, spin-coating process and chemical vapor modification. The prepared membrane exhibited excellent UV resistance due to the synergistic effect of carbon quantum dots (CQDs) as well as UV-absorbing functional groups. The spin-coated AgNPs layer with high infrared reflectivity has great radiant insulation, and temperature was reduced by 3.4 °C compared with H-CEPCM in indoor environment. Furthermore, the mechanical properties of H-AgNPs/CEPCM were significantly improved by the introduction of amide and ether bonds, as well as a large number of hydrogen bonds. This led to a tensile strength of 23.21 MPa and an elongation at break of 16.57 %, while also providing water resistance. Additionally, the H-AgNPs/CEPCM exhibited outstanding thermal stability and hydrophobicity. This work may provide a feasible and promising strategy for the construction of multifunctional integrated cellulose membrane materials for radiant insulation, outdoor textiles and novel UV protection applications.

Cellulose nanocrystal/graphene oxide one-dimensional photonic crystal film with excellent UV-blocking and transparency

Achieving excellent ultraviolet (UV) blocking properties and maintaining high light transmittance are highly challenging. In this study, a facile and green polymer-assisted vacuum filtration strategy was used to prepare cellulose nanocrystal (CNC) one-dimensional photonic crystal (1DPhC) films with excellent UV-blocking performance and good transparency. The polymer-assisted self-assembly behaviors of CNC and the hydrogen bonding interaction between CNC, polyethylene glycol (PEG), and graphene oxide (GO) drive the homogeneous distribution and parallel alignment of GO. The UV absorption of GO and high reflection of UV resulting from the chiral nematic structure of CNCs result in excellent UV-blocking and high visible light transmission. Besides, the strong hydrogen bonding interaction among CNC, PEG, and GO endows the films with obviously increased mechanical properties. The UV-blocking and the transparency of the CNC composite films could reach 98.3 % and 60.5 %, respectively. Besides, the strain at break of the composite film reached 1.72 ± 0.11 %, which was 535.94 % of neat CNC films. The CNC composite films present great potential in the field of UV-blocking glass, sensors, anti-counterfeiting measures, radiation protection, and so on.

Effective reinforcement of plasticized starch by the incorporation of graphene, graphene oxide and reduced graphene oxide

Plasticized starch (PLS) nanocomposite films using glycerol and reinforced with graphene (G) and graphene oxide (GO) were prepared by solvent casting procedure. On one hand, the influence of adding different G contents into the PLS matrix was analyzed. In order to improve the stability of G nanoflakes in water, Salvia extracts were added as surfactants. The resulting nanocomposites presented improved mechanical properties. A maximum increase of 287 % in Young's modulus and 57 % in tensile strength was achieved for nanocomposites with 5 wt% of G. However, it seemed that Salvia acted as co-plasticizer for the PLS. Moreover, the addition of the highest G content led to an improvement of the electrical conductivity close to 5 × 10-6 S/m compared to the matrix. On the other hand, GO was also incorporated as nanofiller to prepare nanocomposites. Thus, the effect of increasing the GO content in the final behavior of the PLS nanocomposites was evaluated. The characterization of GO containing PLS nanocomposites showed that strong starch/GO interactions and a good dispersion of the nanofiller were achieved. Moreover, the acidic treatment applied for the reduction of the GO was found to be effective, since the electrical conductivity was 150 times bigger than its G containing counterpart.

Self-Assembled CNF/rGO/Tannin Composite: Study of the Physicochemical and Wound Healing Properties

In this study, a conductive composite material, based on graphene oxide (GO), nanocellulose (CNF), and tannins (TA) from pine bark, reduced using polydopamine (PDA), was developed for wound dressing. The amount of CNF and TA was varied in the composite material, and a complete characterization including SEM, FTIR, XRD, XPS, and TGA was performed. Additionally, the conductivity, mechanical properties, cytotoxicity, and in vitro wound healing of the materials were evaluated. A successful physical interaction between CNF, TA, and GO was achieved. Increasing CNF amount in the composite reduced the thermal properties, surface charge, and conductivity, but its strength, cytotoxicity, and wound healing performance were improved. The TA incorporation slightly reduced the cell viability and migration, which may be associated with the doses used and the extract's chemical composition. However, the in-vitro-obtained results demonstrated that these composite materials can be suitable for wound healing.

Conductive and antibacterial films by loading reduced graphene oxide/silver nanoparticles on cellulose nanofiber films

The development of sustainable high-performance materials based on nanocellulose has received great attention in recent years. Herein, nanocellulose based composite films with highly electro-conductive and antibacterial properties have been developed by loading reduced graphene oxide (rGO)/silver nanoparticles (AgNPs) on cellulose nanofiber films via vacuum filtration process. The reduction effect of gallic acid on the chemical structure and electrical conductivity of rGO/AgNP composites was studied. Due to the strong reducibility of gallic acid, the obtained rGO/AgNPs exhibited a high electrical conductivity of 1549.2 S·m^-1. Furthermore, the electrical conductivity, mechanical properties and antibacterial properties of the prepared rGO/AgNP-cellulose nanofiber films as a function of various proportions were investigated. The prepared composite film with a specific ratio of rGO/AgNPs to cellulose nanofibers as 7:3 exhibited the superior tensile strength of 28.0 MPa and the electrical conductivity of 1199.3 S·m^-1. Meanwhile, compared with pure cellulose nanofiber films, rGO/AgNP-cellulose nanofiber films displayed strong antibacterial effect against Escherichia coli and Staphylococcus aureus. Therefore, this work demonstrated an effective approach for imparting structural and functional properties to cellulose nanofiber based films, which could hold great application prospects for flexible and wearable electronics.

Sugarcane leave-derived cellulose nanocrystal/graphene oxide filter membrane for efficient removal of particulate matter

The goal of this study is to isolate cellulose nanocrystals (CNC) from sugarcane leaves (SCL) and fabricate filter membranes. Filter membranes consisting of the CNC and varying amount graphene oxide (GO) were fabricated using vacuum filtration technique. The α-cellulose content increased from 53.56 ± 0.49 % in untreated SCL to 78.44 ± 0.56 % and 84.99 ± 0.44 % in steam-exploded and bleached fibers, respectively. Atomic force microscopy (AFM) and transmission electron microscope (TEM) of CNC isolated from SCL indicated nanosized particles in the range of 7.3 nm and 150 nm for diameter and length, respectively. Morphologies of the fiber and CNC/GO membranes were determined by scanning electron microscopy (SEM) and crystallinity by X-ray diffraction (XRD) analysis of crystal lattice. The crystallinity index of CNC decreased with the addition of GO into the membranes. The CNC/GO-2 recorded the highest tensile index of 3.001 MPa. The removal efficiency increases with increasing GO content. The highest removal efficiency of 98.08 % was recorded for CNC/GO-2. CNC/GO-2 membrane reduced growth of Escherichia coli to 65 CFU compared to >300 CFU of control sample. SCL is a potential bioresource for isolation of cellulose nanocrystals and fabrication of high-efficiency filter membrane for particulate matter removal and inhibition of bacteria.

Graphene composite paper synergized with micro/nanocellulose-fiber and silk fibroin for flexible strain sensor

The fabrication of uniform and strong graphene-based conductive paper is challenging due to easy aggregation and poor film formability of graphene. Herein, on the basis of good dispersing effect of nanocellulose, high content graphene (50 wt%) composite paper with micro/nanocellulose fibers and silk fibroin (SF) was manufactured via simple casting method. The synergistic effects of cellulose microfibers (CMFs), cellulose nanofibers (CNFs) and SF result in the paper with ideal combination of flexibility, electrical conductivity and mechanical strength, where CNFs, CMFs and SF act as dispersing and film forming for GNPs, dimensional stability, and interfacial binding agents, respectively. Extraordinarily, by adding SF, graphene nanosheets are tightly coated on the surface of CMFs. The composite paper shows a tensile strength of 49.29 MPa, surface resistance of 39.0-42.1 Ω and good joints bend sensing performance. Additionally, it is found that CMFs can hinder the micro-cracks from propagating during the cyclic elbow bending test. The graphene-based conductive paper is helpful for the development of smart clothing wearable biosensing devices.

Free-standing reduced graphene oxide/carboxymethylcellulose-polyaniline (RGO/CMC-PANI) hybrid film electrode for high-performance asymmetric supercapacitor device

This work demonstrates a facile and effective strategy for the preparation of a reduced graphene oxide/carboxymethylcellulose-polyaniline (RGO/CMC-PANI) hybrid film electrode. Specifically, through the hydrogen bonding interaction between -OH of CMC molecules and -NH₂ of aniline monomer, PANI grows in an ordered manner on the surface of CMC, which effectively alleviates the structural collapse of PANI during the continuous charge/discharge process. After compounding with RGO, CMC-PANI bridges adjacent RGO sheets to form a complete conductive path, and opens the gap between RGO sheet layers to obtain fast ion channels. As a result, the RGO/CMC-PANI electrode exhibits excellent electrochemical performance. Moreover, an asymmetric supercapacitor was fabricated using RGO/CMC-PANI as the anode and Ti₃C₂T_x as the cathode. The results show that the device has a large specific capacitance of 450 mF cm^-2 (81.8 F g^-1) at 1 mA cm^-2 and a high energy density of 140.6 μWh cm^-2 at a power density of 749.9 μW cm^-2. Besides, 87.3 % initial capacitance and 100 % good coulombic efficiency can be maintained even after 20,000 GCD cycles. Therefore, the device has a broad application prospect in the field of new-generation microelectronic energy storage.

A Flexible Vertical-Section Wood/MXene Electrode with Excellent Performance Fabricated by Building a Highly Accessible Bonding Interface

Cross-section wood (CW) is generally used as a host for free-standing electrodes, as the abundant opened pores can provide large space for loading guest materials with high electrical conductivity and electrochemical activity. However, there is still a challenge for CW to be used in flexible supercapacitors (SCs) because of its low mechanical strength. Herein, as an alternative to CW, vertical-section wood (VW) with excellent mechanical strength and good flexibility is developed and used as a free-standing and flexible electrode by using Ti₃C₂T_x (MXene) with ultrahigh conductivity and good electrochemical activity as a guest material. In particular, the highly accessible bonding interface for Ti₃C₂T_x is first built by delignification on VW to generate abundant pores for continuously absorbing Ti₃C₂T_x and to expose cellulose with abundant oxygen-containing groups for stable combination with Ti₃C₂T_x. Then, cyclic pressing is used to form negative pressure to pump the Ti₃C₂T_x suspension into VW, combining with a preheating process to trigger layer-by-layer self-assembly of Ti₃C₂T_x nanosheets onto a wood cell wall by evaporating water in the suspension. As a result, the free-standing electrode has a large Ti₃C₂T_x loading mass proportion of 33 wt %, a high conductivity of 3.14 S cm^-1, and good flexibility with much higher mechanical strength of 15.1 MPa than 0.4 MPa of CW. The symmetric SC delivers a good specific capacitance of 805 mF cm^-2 at 0.5 mA cm^-2, a remarkably high rate capability of 84% to 10 mA cm^-2, and an energy density of 13.85 μW h cm^-2 at 87.5 μW cm^-2. Additionally, this SC shows a long lifespan of 90.5% after 10,000th charge and discharge cycles even at a constant bending angle of 90°, suggesting promising potential in flexible devices.