Core-shell alginate beads as green reactor to synthesize grafted composite beads to efficiently boost single/co-adsorption of dyes and Pb(II)

Removal of Pb pollution using alginate-coupled magnetic sludge biochar: Solidification and stabilization behavior and electron promotion mechanisms

Environmental and human health problems caused by Pb pollution have attracted much attention, and solidification and stabilization are effective means for its remediation. Improving the ability of biochar to remediate heavy metals through modification is the focus of current biochar research. This study used calcium-alginate gel (GB) and Fe3+ (magnetic) to encapsulate and improve sludge biochar (SB), and explored the adsorption behavior and passivation mechanism of Pb2+ on it from outside to inside. The magnetic-biochar (MB) in magnetic-biochar-gel microspheres (MBGB) showed a homogeneous dispersion and part of the Fe ion was detached from the MB into the three-dimensional pores of the gel. The results of kinetic, isothermal and pH adsorption experiments showed that the MBGB has 108.4 % and 200 % higher Pb2+ adsorption capacity and rate than SB and can be applied to pH 3-9. The adsorption of Pb2+ by MBGB is a multilayer adsorption with both physical and chemical mechanisms. Mineralogical and electrochemical results demonstrate that the cross-linking of the gel with magnetic-biochar (MB) can provide a directional diffusion channel for Pb2+ from the outside to the inside. The electron transfer rate of MBGB was significantly higher than that of SB (222.2 %) after the reaction. The dissolved cations and electrons on the MB guide Pb2+ from the MBGB surface to the internal MB quickly via accelerating the electron transfer and migration rate between Pb2+ and MB. Subsequently, the abundance of PO43- on the MB ensures stable mineral precipitation (Pyromorphite). Moreover, four-step extraction analysis confirmed that most of Pb2+ in MBGB was stable (36.2 % acid-soluble and 47.6 % non-bioavailable). Meanwhile, the Pb adsorption efficiency of MBGB was still >93.0 % after three cycles of adsorption-desorption. Excellent reuse performance and stability guarantee the environmental security of MBGB. The results of the study provide theoretical support for the efficient treatment of Pb2+ polluted water assisted by gel materials.

Biopolymer Meets Nanoclay: Rational Fabrication of Superb Adsorption Beads from Green Precursors for Efficient Capture of Pb(II) and Dyes

Renewable, green, and safe natural biopolymer-derived materials are highly desired for the purification of pollutants, but significantly improving their performance without the introduction of additional harmful chemicals remains a huge challenge. Based on the concept of "structure optimization design", environment-friendly composite beads (named SA/PASP/RE) with excellent adsorption performance and recyclability were rationally constructed through a green ionic crosslinking route, using the completely green biopolymer sodium alginate (SA), sodium salt of polyaspartic acid (PASP), and the natural nanoclay rectorite (RE) as starting materials. The nano-layered RE was embedded in the polymer matrix to prevent the polymer chain from becoming over-entangled so that more adsorption sites inside the polymer network were exposed, which effectively improved the mass transfer efficiency of the adsorbent and the removal rate of contaminants. The composite beads embedded with 0.6% RE showed high adsorption capacities of 211.78, 197.13, and 195.69 mg/g for Pb(II) and 643.00, 577.80, and 567.10 mg/g for methylene blue (MB) in Yellow River water, Yangtze River water, and tap water, respectively. And the beads embedded with 43% RE could efficiently adsorb Pb(II) and MB with high capacities of 187.78 mg/g and 586.46 mg/g, respectively. This study provides a new route to design and develop a green, cost-effective, and efficient adsorbent for the decontamination of wastewater.

The remediation potential and kinetics of Pb2+ adsorbed by the organic frameworks of Cladophora rupestris

Cladophora rupestris is ubiquitous in many kinds of waterbodies, and C. rupestris biomass can serve as a carrier for adsorbing and transferring heavy metals. Batch experiments and characterization were performed. Results showed that the organic frameworks of C. rupestris (CROF) had a specific surface area of 2.58 m2/g and an external surface area of 2.06 m2/g. Many mesopores were present in CROF, mainly distributed in 2.5-7.5 nm. The zeta potentials were within the range of - 4.46 to - 13.98 mV in the tested pH of 2.0-9.0. CROF could effectively adsorb Pb2+ in large pH range. The maximum adsorption capacity (qmax) of Pb2+ on CROF was 15.02 mg/g, and 97% of Pb2+ was adsorbed onto CROF after 25 min. CROF had a preferential adsorption of Pb2+. The protein secondary structures and carbon skeletons of CROF all worked in adsorption. The main Pb2+ adsorption mechanisms were pore filling, electrostatic attraction, Pb-π interaction, and surface complexation. Therefore, it is valuable as a biosorbent for the removal of Pb2+ from waterbodies.

The influence of electrolytes in the adsorption kinetics of reactive BF-5G blue dye on bone char: a mass transfer model

The discharge of harmful dyes in water bodies is a serious pollution problem, dangerous for the ecosystem's equilibrium and human health. In this sense, the aim of this work was to determine the influence of electrolytes (NaCl, KCl, CaCl2 and MgCl2) in the adsorption of Reactive Blue BF-5G dye, the most common dye used in industrial process for fabric colouring, using bovine bone char as the adsorbent. The bovine bone char was characterized by pH of point of zero charge (pHPZC), N2 adsorption-desorption isotherms, Fourier transform-infrared spectroscopy (FT-IR) and X-ray diffractometry (XDR). The characterization revealed a mesoporous structure (pore mean diameter of 94 Å and SBET ∼107 m2 g-1) with negative charge distribution at the surface (pHPZC = 3.8). The adsorption experiments revealed that the presence of KCl enhanced the material adsorption capacity (qmax = 195 mg g-1), that the Sips isotherm best fitted the experimental data (R2 > 0.9 except for KCl solution) and the adsorption process was mono- and multilayered. The kinetic adsorption experiments indicated that the inorganic electrolytes increased the initial adsorption velocity and the data was best modelled by the surface diffusional model (SDM), implying a resistance (aqueous > CaCl2 > NaCl > MgCl2 > KCl) to mass transfer at the surface of the pores which, in turn, prevented the dye diffusion to the interior of the adsorbent (qe = 71 mg g-1). Therefore, small quantities of KCl can be used to lower the mass transfer resistance and provide higher adsorption capacity with reduced time of operation, thus increasing the overall process efficiency.

Insight into adsorption process and mechanisms of Cr(III) using carboxymethyl cellulose-g-poly(acrylic acid-co-acrylamide)/attapulgite composite hydrogel

Cr(III) as one of the most concerned potentially toxic elements, is discharged from relevant industries and Cr(VI) reduction. Hydrogel-based adsorption could be one of the promising approaches for Cr(III) removal. Featured with environmental friendliness and low cost, carboxymethyl cellulose (CMC) was employed for the hydrogel synthesis, and attapulgite (APT) could be used to strengthen its stability. However, the adsorption performance and mechanisms need to be examined. In the present study, carboxymethyl cellulose-g-poly(acrylic acid-co-acrylamide)/ attapulgite (CMC-g-p(AA-co-AM)/APT) was synthesised via in situ copolymerisation. Its efficacy for removing Cr(III) from an aqueous solution was investigated using batch adsorption experiments. Results showed that the introduction of APT enhanced the thermal stability but decreased the swelling performance of the hydrogel. The prepared hydrogel could strongly adsorb Cr(III) at a wide pH range of 3.0-7.0. Cr(III) can be efficiently removed by the composite hydrogel within 1-2 h. At low concentration, CMC-g-p(AA-co-AM)/APT could slightly adsorbed more Cr(III) than CMC-g-p(AA-co-AM). The maximum absorption of CMC-g-p(AA-co-AM) and CMC-g-p(AA-co-AM)/APT were 74.8 and 47.7 mg/g at 298 K, respectively. The negative value of ΔHo and ΔGo indicated the adsorption of Cr(III) onto the two studied hydrogels is an exothermic and spontaneous process. Ion exchange and complexation, as implied by EDS, FT-IR and XPS, combining with electrostatic attraction are the possible adsorption mechanisms for Cr(III) onto the prepared hydrogels. All the results above suggests that the composite hydrogel CMC-g-p(AA-co-AM)/APT can be a promising candidate for the removal of Cr(III) from waste water.

Removal of crystal violet dye using a three-dimensional network of date pits powder/sodium alginate hydrogel beads: Experimental optimization and DFT calculation

Biodegradable and very low-cost adsorbent beads were prepared from date pits powder (DP) and sodium alginate (SA). DP to SA ratios was varied (1/2, 1/4 and 1/6) and used to eliminate Crystal violet (CV) a cationic dye. Adsorbents were characterized by FTIR, SEM-EDS, UV-vis DR, TGA and the point of zero charge (pHPZC). The optimal composite beads SA@6DP show high adsorption capacities of 83.565 mg/g toward CV than SA@2DP and SA@4DP. The kinetics investigation showed that the adsorption is well described by the pseudo-second-order kinetic (R2 = 0.998). The thermodynamics and isotherms studies exhibit that the adsorption phenomenon for SA@6DP adsorbent is endothermic and significantly fitted with the Redlich-Peterson model. The experimental adsorption tests were optimized by the Box-Behnken design (BBD) which led to conclude the maximal CV removal efficiency achieved by SA@6DP was 99.873 % using [CV] = 50 mg/L, adsorbent mass = 20 mg and 48 h of contact time. The theoretical calculation proved that the CV molecules favor the mode of attack due to their electrophilic character and can accept the SA@6DP adsorbent electrons more easily to form an anti-bonding orbital. SA@6DP hydrogel beads are therefore an exceptional bio-adsorbent that offers excellent adsorption performance.

Carbon-in-Silicate Nanohybrid Constructed by In Situ Confined Conversion of Organics in Rectorite for Complete Removal of Dye from Water

The complete removal of low concentration organic pollutants from wastewater to obtain clean water has always been a highly desired but challenging issue. In response to this, we proposed a new strategy to fabricate a carbon-in-silicate nanohybrid composite by recycling dye-loaded layered clay adsorbent and converting them to new heterogeneous carbon-in-silicate nanocomposite through an associated calcination-hydrothermal activation process. It has been confirmed that most of the dye molecules were present in waste rectorite adsorbent using an intercalation mode, which can be in situ converted to carbon in the confined interlayer spacing of rectorite. The further hydrothermal activation process may further improve the pore structure and increase surface active sites. As expected, the optimal composite shows extremely high removal rates of 99.6% and 99.5% for Methylene blue (MB) and Basic Red 14 (BR) at low concentrations (25 mg/L), respectively. In addition, the composite adsorbent also shows high removal capacity for single-component and two-component dyes in deionized water and actual water (i.e., Yellow River water, Yangtze River water, and seawater) with a removal rate higher than 99%. The adsorbent has good reusability, and the adsorption efficiency is still above 93% after five regeneration cycles. The waste clay adsorbent-derived composite adsorbent can be used as an inexpensive material for the decontamination of dyed wastewater.

Sustainable green conversion of coal gangue waste into cost-effective porous multimetallic silicate adsorbent enables superefficient removal of Cd(II) and dye

Converting solid wastes into new materials for wastewater decontamination is a feasible "one stone, three birds" strategy to achieve sustainable value-added utilization of resources and minimize waste emissions, but significant challenges remain. In response to this, we proposed an efficient "mineral gene reconstruction" method to synchronously transform coal gangue (CG) into a green porous silicate adsorbent without using any harmful chemicals (i.e., surfactants, organic solvents). The one of the synthesized adsorbents with a high specific surface area (582.28 m²/g) and multimetallic active centres shows outstanding adsorption performance (adsorption capacities: 168.92 mg/g for Cd(II), 234.19 mg/g for methylene blue (MB); removal rate: 99.04% for Cd(II) and 99.9% for MB). The adsorbent can also reach a high removal rate of 99.05%∼99.46% and 89.23%∼99.32% for MB and Cd(II) in real water samples (i.e., Yangtze River, Yellow River, seawater and tap water), respectively. After 5 adsorption-desorption cycles, the adsorption efficiency remained above 90%. The adsorbents mainly adsorbed Cd(II) by electrostatic attraction, surface complexation and partial ion exchange and MB by electrostatic and hydrogen bonding interactions. This study provides a sustainable and promising platform for developing a new-generation cost-efficient adsorbent from waste for clean water production.

Chitosan-based composite hydrogel with a rigid-in-flexible network structure for pH-universal ultra-efficient removal of dye

Polysaccharide-based hydrogel adsorbents become popular because of their high adsorption capacity and fast adsorption rate, but their low removal rate and poor pH resistance have always been fatal shortcomings. Herein, a feasible strategy was proposed to strengthen the ability of hydrogel adsorbent to remove organic pollutants (i.e., dye) by incorporating natural rectorite (REC) into chitosan-g-poly (2-acrylamido-2-methyl-propane-sulfonic-acid) hydrogel network to form a rectorite-in-polymer network structure. The introduction of less dosage of REC (1.2 wt%) into the hydrogel facilitates to improve its adsorption capacities toward methylene blue (MB) in deionized water, tap water, seawater, Yangtze River water, and Yellow River water (1083.39-1303.49 mg/g); while incorporating higher content of REC (15.8 wt% REC) helps to improve the removal rate (99.6 % for MB in real waters), which are greatly superior to commercial activated carbons. The adsorbent keeps high adsorption efficiency in a broad pH range (2-11), and can be reused for >4 times.

Green and Superior Adsorbents Derived from Natural Plant Gums for Removal of Contaminants: A Review

The ubiquitous presence of contaminants in water poses a major threat to the safety of ecosystems and human health, and so more materials or technologies are urgently needed to eliminate pollutants. Polymer materials have shown significant advantages over most other adsorption materials in the decontamination of wastewater by virtue of their relatively high adsorption capacity and fast adsorption rate. In recent years, "green development" has become the focus of global attention, and the environmental friendliness of materials themselves has been concerned. Therefore, natural polymers-derived materials are favored in the purification of wastewater due to their unique advantages of being renewable, low cost and environmentally friendly. Among them, natural plant gums show great potential in the synthesis of environmentally friendly polymer adsorption materials due to their rich sources, diverse structures and properties, as well as their renewable, non-toxic and biocompatible advantages. Natural plant gums can be easily modified by facile derivatization or a graft polymerization reaction to enhance the inherent properties or introduce new functions, thus obtaining new adsorption materials for the efficient purification of wastewater. This paper summarized the research progress on the fabrication of various gums-based adsorbents and their application in the decontamination of different types of pollutants. The general synthesis mechanism of gums-based adsorbents, and the adsorption mechanism of the adsorbent for different types of pollutants were also discussed. This paper was aimed at providing a reference for the design and development of more cost-effective and environmentally friendly water purification materials.