A fungal cellulose nanocrystals-based approach to improve the stability of triterpenes loaded Pickering emulsion

Analysis of instability of starch-based Pickering emulsion under acidic condition of pH < 4 and improvement of emulsion stability

Starch-based Pickering emulsions exhibit high interfacial stability in a certain range of mild pH environments. On the contrary, many studies have reported that when the pH value is <4, it often leads to different degrees of emulsion instability. In this paper, the microscopic state of starch granules in the emulsion and its effect on the stability of the emulsion were observed and analyzed by atomic force microscope (AFM) in tapping mode. At the same time, Pickering emulsions in acidic environment were prepared by using the gel properties of methyl cellulose (MC) in synergy with esterified high amylose maize starch (M-HAMS) granules. The results show that in the emulsion with pH 3, the excessive H + ion inhibits the swelling of M-HAMS granules and prevents it from forming a stable gel structure, which is the main cause of emulsion instability. The polarity of MC with water contact angle (WCA) of 81.8° is similar to that of M-HAMS granules with WCA of 80.1°, and a uniform and ordered micro-nanostructure is formed in the aqueous phase. The prepared acidic (pH 3-4) emulsion has good stability during the observation period of 30 days.

Large-Scale Preparation of Carboxylated Cellulose Nanocrystals and Their Application for Stabilizing Pickering Emulsions

Cellulose nanocrystals (CNCs) with varied unique properties have been widely used in emulsions, nanocomposites, and membranes. However, conventional CNCs for industrial use were usually prepared through acid hydrolysis or heat-controlled methods with sulfuric acid. This most commonly used acid method generally suffers from low yields, poor thermal stability, and potential environmental pollution. Herein, we developed a high-efficiency and large-scale preparation strategy to produce carboxylated cellulose nanocrystals (Car-CNCs) via carboxymethylation-enhanced ammonium persulfate (APS) oxidation. After carboxymethylation, the wood fibers could form unique "balloon-like" structures with abundant exposed hydroxy groups, which facilitated exfoliating fibril bundles into individual nanocrystals during the APS oxidation process. The production process under controlled temperature, time period, and APS concentrations was optimized and the resultant Car-CNCs exhibited a typical structure with narrow diameter distributions. In particular, the final Car-CNCs exhibited excellent thermal stability (≈346.6 °C) and reached a maximum yield of 60.6%, superior to that of sulfated cellulose nanocrystals (Sul-CNCs) prepared by conventional acid hydrolysis. More importantly, compared to the common APS oxidation, our two-step collaborative process shortened the oxidation time from more than 16 h to only 30 min. Therefore, our high-efficiency method may pave the way for the up-scaled production of carboxylated nanocrystals. More importantly, Car-CNCs show potential for stabilizing Pickering emulsions that can withstand changeable environments, including heating, storage, and centrifugation, which is better than the conventional Sul-CNC-based emulsions.

Pentacyclic triterpene-loaded emulsion stabilized by Agaricus blazei Murill polysaccharides: Factorial design and cytoprotection study

In this study, pentacyclic triterpene-loaded emulsions were stabilized by polysaccharides from Agaricus blazei Murill mushroom (PAb). The drug-excipient compatibility results by Fourier Transform Infrared Spectroscopy (FTIR) and Differential Scanning Calorimetry (DSC) showed the absence of physicochemical incompatibilities. The use of these biopolymers at 0.75 % led to obtaining emulsions with droplets smaller than 300 nm, moderate polydispersity, and ζ-potential >30 mV in modulus. The emulsions presented high encapsulation efficiency, suitable pH for topical application, and absence of macroscopic signs of instability during 45 days. Morphological analysis suggested the deposition of thin layers of PAb around the droplets. The encapsulation of pentacyclic triterpene in emulsions, stabilized by PAb, improved the cytocompatibility of this drug against PC12 and murine astrocyte cells. There was a reduction in cytotoxicity, which resulted in a lower accumulation of intracellular reactive oxygen species and maintenance of the mitochondrial transmembrane potential. Based on these results, it is estimated that PAb are promising biopolymers for the emulsions' stabilization by improving their physicochemical and biological properties.

Impact of interactions between peanut protein isolate and cellulose nanocrystals on the properties of Pickering emulsions: Rheological properties and physical stabilities

The interactions between cellulose nanocrystals and proteins can regulate the interfacial properties of Pickering emulsions, which plays a leading role in the stabilities of Pickering emulsions. In this work, oil-in-water (O/W) Pickering emulsions with different oil-water ratios were prepared using peanut protein isolate modified by cellulose nanocrystals (PPI/CL-CNCs). The distributions of PPI/CL-CNCs at the oil-water interfaces and the microstructures of Pickering emulsions were observed by CLSM and cryo-SEM. The results showed that stable complexes PPI/CL-CNCs formed thick and dense interface layers on the surface of oil droplets. The results of rheological tests clarified that the Pickering emulsions showed an elastic and gel texture, and their gel strength could be enhanced by regulating the oil-water ratios from 3:7 to 7:3. In addition, after one month of storage, the EI of all emulsions remained above 92 % with no obvious phase separation or demulsification. These results suggested that the PPI/CL-CNCs-stabilized Pickering emulsions showed good physical stabilities. The study on the rheological properties and physical stabilities of PPI/CL-CNCs-based Pickering emulsions provided novel insights on developing highly stable Pickering emulsions.

Recent advances in bioactive nanocrystal-stabilized Pickering emulsions: Fabrication, characterization, and biological assessment

Numerous literatures have shown the advantages of Pickering emulsion (PE) for the delivery of bioactive ingredients in the fields of food, medicine, and cosmetics, among others. On this basis, the multi-loading mode of bioactives (internal phase encapsulation and/or loading at the interface) in small molecular bioactives nanocrystal-stabilized PE (BNC-PE) enables them higher loading efficiencies, controlled release, and synergistic or superimposed effects. Therefore, BNC-PE offers an efficacious delivery system. In this review, we briefly summarize BNC-PE fabrication and characterization, with a focus on the processes of possible evolution and absorption of differentially applied BNC-PE when interacting with the body. In addition, methods of monitoring changes and absorption of BNC-PE in vivo, from the nanomaterial perspective, are also introduced. The purpose of this review is to provide an accessible and comprehensive methodology for the characterization and evaluation of BNC-PE after formulation and preparation, especially in relation to biological assessment and detailed mechanisms throughout the absorption process of BNC-PE in vivo.