Removal of copper using chitosan beads embedded with amidoxime grafted graphene oxide nanohybids

Bifunctional solid-state ionic liquid supported amidoxime chitosan adsorbents for Th(IV) and U(VI): Enhanced adsorption capacity from the synergistic effect

Uranium and thorium of symbiotic relationship commonly appear in one kind of raw or spent ore. The simultaneous enrichment toward both metals in the first step is essential during many hydrometallurgy processing. Therefore bifunctional solid-state ionic liquid supported amidoxime chitosan (ACS) adsorbents were developed to simultaneously adsorb the two metal from the aqueous solution. The adsorption capacity of the bifunctional adsorbents toward uranium and thorium were significantly superior to the ionic liquid-free amidoxime chitosan, obviously proving the synergistic effect. For both uranium and thorium, the adsorption capacity in the consequence of ACS-[N4444][DEHP], ACS-[N4444][EHEHP], ACS-[N1888][DEHP] and ACS-[N1888][EHEHP] prove the steric effect and PO bonding played important roles in the adsorption. Study on isotherms and kinetics demonstrated the adsorption of ionic liquid-ACS adopted monolayer and chemical way. The ΔGo of very small negative values highlighted ionic liquid-ACS were prone to adsorb uranium and thorium. The study showed feasibility of bifunctional solid-state ionic liquid supported amidoxime chitosan adsorbents for Th(IV) and U(VI).

Polydopamine-functionalized electrospun poly(vinyl alcohol)/chitosan nanofibers for the removal and determination of Cu(II)

Environmentally friendly and recycled polydopamine-functionalized electrospun poly(vinyl alcohol)/chitosan nanofibers (PVA/CS/PDA) were prepared through a low-energy-consumption procedure. The PDA coating endows PVA/CS/PDA nanofibers with good water stability. The PVA/CS/PDA nanofibers have a fibrillar and porous structure that is favorable for Cu(II) to access the active sites of the nanofibers. The adsorption isotherm and kinetics data preferably conform to the Liu isotherm and pseudo-second-order kinetic models, respectively. The maximum adsorption capacity of Cu(II) ions by PVA/CS/PDA nanofibers from the Liu isotherm model is 326.5 mg g-1. The PVA/CS/PDA nanofibers exhibit higher adsorption capacity than some other reported adsorbents. The adsorption mechanism study demonstrates that the Cu(II) adsorption is mainly ascribed to the complexation of Cu(II) with the imino, amino, and hydroxy moieties in PVA/CS/PDA nanofibers. The nanofibers can be employed for 5 cycles without significantly deteriorating performance. More interestingly, a fluorometry method based on the oxidation mimic enzyme activity of Cu(II) was developed to detect low concentrations of Cu(II) using the nanofibers as an adsorbent to preconcentrate Cu(II). The limit of detection is 0.42 mg L-1. The successful removal and detection of Cu(II) in Pearl River and mineral water samples demonstrates the great potential of PVA/CS/PDA nanofibers to remediate Cu(II)-polluted water.

Exploration of Reactive Black 5 Dye Desorption from Composite Hydrogel Beads—Adsorbent Reusability, Kinetic and Equilibrium Isotherms

A low-cost adsorbent was prepared by using cherry stones powder and chitosan and used to retain Reactive Black 5 dye from aqueous solution. Then, the spent material was submitted to a regeneration process. Five different eluents (water, sodium hydroxide, hydrochloric acid, sodium chloride and ethanol) were tested. Among them, sodium hydroxide was selected for an advanced investigation. Values of three working conditions, namely the eluent volume, its concentration and the desorption temperature, were optimized by Response Surface Methodology-Box–Behnken Design. In the established settings (NaOH volume: 30 mL, NaOH concentration: 1.5 M, working temperature: 40 °C), three successive cycles of adsorption/desorption were conducted. The analysis performed by Scanning Electron Microscopy and by Fourier Transform Infrared Spectroscopy revealed the evolution of the adsorbent throughout the dye elution from the material. Pseudo-second-order kinetic model and Freundlich equilibrium isotherm were able to accurately describe the desorption process. Based on the acquired results, our outcomes sustain the suitability of the synthesized material as dye adsorbent and the possibility of efficaciously recycling and reusing it.

Performance of Dye Removal from Single and Binary Component Systems by Adsorption on Composite Hydrogel Beads Derived from Fruits Wastes Entrapped in Natural Polymeric Matrix

The treatment of contaminated water is currently a major concern worldwide. This work was directed towards the preparation of a composite hydrogel by entrapping cherry stones powder on chitosan, which is known as one of the most abundant natural polymers. The synthesized material was characterized by scanning electron microscopy, by Fourier transform infrared spectroscopy, and by the point of zero charge determination. Its ability to remove two azo dyes models (Acid Red 66 and Reactive Black 5) existing in single form and in binary mixture was evaluated. Response Surface Methodology-Central Composite Design was used to optimize three parameters affecting the process while targeting the lowest final contaminant concentrations. The best results were obtained at pH 2, an adsorbent dose of 100 g/L, and a temperature of 30 °C, when more than 90% of the pollutants from the single component systems and more than 70% of those of the binary mixtures were removed from their aqueous solutions. The adsorption process was in accordance with Elovich and pseudo-second-order kinetic models, and closely followed the Freundlich and Temkin equilibrium isotherms. The obtained results led to the conclusion that the prepared hydrogel composite possesses the ability to successfully retain the target molecules and that it can be considered as a viable adsorbent material.