Drug release from complexes with a series of poly(carboxyalkyl methacrylates), a new class of weak polyelectrolytes

Effects of Non-Ionic Micelles on the Acid-Base Equilibria of a Weak Polyelectrolyte

Weak polyelectrolytes (WPEs) are widely used as pH-responsive materials, pH modulators and charge regulators in biomedical and technological applications that involve multi-component fluid environments. In these complex fluids, coupling between (often weak) interactions induced by micelles, nanoparticles and molecular aggregates modify the pKa as compared to that measured in single component solutions. Here we investigated the effect of coupling between hydrogen bonding and excluded volume interactions on the titration curves and pKa of polyacrylic acid (PAA) in solutions comprising PEO-based micelles (Pluronics and Brij-S20) of different size and volume fraction. Titration experiments of dilute, salt-free solutions of PAA (5 kDa, 30 kDa and 100 kDa) at low degree of polymer ionization (α < 0.25) drive spatial re-organization of the system, reduce the degree of ionization and consequentially increase the pKa by up to ~0.7 units. These findings indicate that the actual degree of ionization of WPEs measured in complex fluids is significantly lower (at a given pH) than that measured in single-component solutions.

The study of release of chlorhexidine from preparations with modified thermosensitive poly-N-isopropylacrylamide microspheres

The aim of this study was to investigate and compare the release rates of chlorhexidine (CX) base entrapped in the polymeric beads of modified poly-N-isopropylacrylamides (pNIPAMs) at temperatures below and over the volume phase transition temperature (VPTT) of synthesized polymers: pNIPAM-A with terminal anionic groups resulting from potassium persulfate initiator, pNIPAM-B with cationic amidine terminal groups, and pNIPAM-C comprising anionic terminals, but with increased hydrophobicity maintained by the N-tert-butyl functional groups. The preparations, assessed in vitro below the VPTT, release an initial burst of CX at different time periods between 120 and 240 min, followed by a period of 24 h, when the rate of release remains approximately constant, approaching the zero-order kinetics; the release rates for the polymers beads are as follows: pNIPAM-C>pNIPAM-B>pNIPAM-A. The pattern of release rates at temperature over the VPTT is as follows: pNIPAM-C>pNIPAM-A>pNIPAM-B. In the presence of pNIPAM-C, the duration between the start of the release and the attained minimal inhibitory concentration (MIC) for most of the microbes, in conditions over the VPTT, increased from 60 to 90 min. The release prolongation could be ascribed to some interactions between the practically insoluble CX particle and the hydrophobic functional groups of the polymer.

pH Sensitive graft copolymers for zero order drug release: a mechanistic analysis

Aliphatic polyesters containing pendent unsaturation were synthesized by the polycondensation of a diol, dicarboxylic acid and glycidyl methacrylate. Grafting methacrylic acid (MAA) resulted in graft copolymers containing polyester backbone and MAA grafts. Depending on composition, the polymers swelled extensively and eroded or dissolved at near neutral pH but remained in collapsed state at acidic pH. Three representative drugs differing in solubility, viz., Diltiazem hydrochloride (DH), Indomethacin (IM) and Verapamil hydrochloride (VH) were released at constant rate from tablets made by compressing spray-dried microparticles. The release of DH at constant rate has been attributed to increase in diffusion coefficient of the drug from the swollen layer of matrix. The release of IM and VH at constant rate was governed by erosion and was enhanced in matrices which undergo dissolution. The release rate was enhanced with increasing MAA content and the frequency of grafts along the polyester backbone. Once a day dosage forms for drugs differing in solubility have been developed using a single polymer matrix which is easy to manufacture.