Nanometer depth resolution in 3D topographic analysis of drug-loaded nanofibrous mats without sample preparation

Hydroxypropyl methylcellulose-based micro- and nanostructures for encapsulation of melanoidins: Effect of electrohydrodynamic processing variables on morphological and physicochemical properties

Electrohydrodynamic processing (EHDP) allows the use of a wide range of biopolymers and solvents, including food-grade biopolymers and green solvents, for the development of micro- and nanostructures. These structures present a high surface-area-to-volume ratio and different shapes and morphologies. The aim of this work was to design and produce hydroxypropyl methylcellulose (HPMC)-based micro- and nanostructures through EHD processing using green solvents, while exploring the influence of process and solution parameters, and incorporating a bioactive extracted from a food by-product. Low (LMW) and high (HMW) molecular weight HPMC have been used as polymers. The design-of-experiments methodology was used to determine the effects of process parameters (polymer concentration, flow rate, tip-to-collector distance, and voltage) of EHDP on the particle and fibre diameter, aspect ratio, diameter distribution, aspect ratio distribution, and percentage of fibre breakage. Additionally, melanoidins extracted from spent coffee grounds were encapsulated into the HPCM-based structures at a concentration of 2.5 mg melanoidins/mL of the polymer solution. Polymer solutions were characterised regarding their viscosity, surface tension and conductivity, and showed that the incorporation of melanoidins increased the viscosity and conductivity values of the polymer solutions. The developed structures were characterised regarding their thermal properties, crystallinity and morphology before and after melanoidin incorporation and it was observed that melanoidin incorporation did not significantly influence the characteristics of the produced micro- and nanostructures. Based on the results, it is possible to envision the use of the produced micro- and nanostructures in a wide range of applications, both in food and biomedical fields.

Quasi-Dynamic Dissolution of Electrospun Polymeric Nanofibers Loaded with Piroxicam

We investigated and monitored in situ the wetting and dissolution properties of polymeric nanofibers and determined the solid-state of a drug during dissolution. Piroxicam (PRX) was used as a low-dose and poorly-soluble model drug, and hydroxypropyl methylcellulose (HPMC) and polydextrose (PD) were used as carrier polymers for electrospinning (ES). The initial-stage dissolution of the nanofibers was monitored in situ with three-dimensional white light microscopic interferometry (SWLI) and high-resolution optical microscopy. The physical solid-state characterization of nanofibers was performed with Raman spectroscopy, X-ray powder diffraction (XRPD), and scanning electron microscopy (SEM). We showed that PRX recrystallizes in a microcrystalline form immediately after wetting of nanofibers, which could lead to enhanced dissolution of drug. Initiation of crystal formation was detected by SWLI, indicating: (1) that PRX was partially released from the nanofibers, and (2) that the solid-state form of PRX changed from amorphous to crystalline. The amount, shape, and size of the PRX crystals depended on the carrier polymer used in the nanofibers and dissolution media (pH). In conclusion, the present nanofibers loaded with PRX exhibit a quasi-dynamic dissolution via recrystallization. SWLI enables a rapid, non-contacting, and non-destructive method for in situ monitoring the early-stage dissolution of nanofibers and regional mapping of crystalline changes (re-crystallization) during wetting. Such analysis is crucial because the wetting and dissolution of nanofibers can greatly influence the performance of nanofibrous drug delivery systems in pharmaceutical and biomedical applications.

Subsurface metrology using scanning white light interferometry: absolute z coordinates deep inside displays

Mobile devices with interactive displays are ubiquitous commodities. Efficient quality control (QC) drives competitiveness. Scanning white light interferometry imaging offers a fast and nondestructive tool for QC purposes. Relying on optical compensation and image stitching, one can rapidly and cost-effectively produce sharp 3D images of a display's inner structures with a few nanometers' accuracy along the z direction. As a practical example, 3D images of a mobile device display revealed 0.92±0.02  μm height variation in the top glass assembly. The proposed method improves quality assurance methods of display manufacturing.