Investigation into the role of the polymer in enhancing microwave-induced in situ amorphization

Use of solid thermolytic salts to facilitate microwave-induced in situ amorphization

Moisture was frequently used as dielectric heating source in classical microwave-able systems to facilitate microwave-induced in situ amorphization, however such systems may face the potential of drug hydrolysis. In this study, solid thermolytic salts were proposed to function as moisture substitutes and their feasibility and impacts on microwave-induced in situ amorphization were investigated. It was found that NH4HCO3 was a promising solid alkaline salt to facilitate both microwave-induced in situ amorphization and in situ salt formation of acidic indomethacin (IND). Moreover, it could improve the chemical stability of the drug and the dissolution performance of compacts relative to classical moisture-based compacts upon microwaving. Further mechanistic study suggested that the in situ amorphization occurred prior to the in situ salt formation, especially in formulations with low drug loadings and high solid salt mass ratios. For compacts with low polymer ratios, in situ salt formation took place subsequently, where the previously amorphized IND within compacts could interact with the NH3 gas produced in situ by the decomposition of NH4HCO3 and form the ammonium IND salt. Microwaving time showed great impacts on the decomposition of NH4HCO3 and the in situ generation of water and NH3, which indirectly affected the amorphization and salt formation of IND. In comparison to the moisture-based systems, the NH4HCO3-based system showed a number of advantages, including the reduced potential of IND hydrolysis due to the absence of absorbed moisture, a wider category of applicable polymeric carriers other than hygroscopic polymers, and an increase in drug loading up to 50% (w/w).

Advances in the development of amorphous solid dispersions: The role of polymeric carriers

Amorphous solid dispersion (ASD) is one of the most effective approaches for delivering poorly soluble drugs. In ASDs, polymeric materials serve as the carriers in which the drugs are dispersed at the molecular level. To prepare the solid dispersions, there are many polymers with various physicochemical and thermochemical characteristics available for use in ASD formulations. Polymer selection is of great importance because it influences the stability, solubility and dissolution rates, manufacturing process, and bioavailability of the ASD. This review article provides a comprehensive overview of ASDs from the perspectives of physicochemical characteristics of polymers, formulation designs and preparation methods. Furthermore, considerations of safety and regulatory requirements along with the studies recommended for characterizing and evaluating polymeric carriers are briefly discussed.

The effects of surfactants on the performance of polymer-based microwave-induced in situ amorphization

Microwave-induced in situ amorphization is a novel technology for preparing amorphous solid dispersions (ASDs) to address the challenges of their long-term physical stability and downstream processing. To date, only few types of dielectric materials have been reported for microwave-induced in situ amorphization, which restricted the extensive research of this technology. This study aimed to investigate the feasibility and mechanisms of utilizing the non-ionic surfactants, i.e. Kollisolv P124, Kolliphor RH40, D-ɑ-tocopheryl polyethylene glycol succinate (TPGS), Tween (T) 60 (T60), T65, T80 and T85, as plasticizers to facilitate microwave-induced in situ amorphization. It was found that the successful application of surfactants could be related with their low T_m, low M_w and high HLB. Kolliphor RH40 was selected as a typical surfactant due to its excellent dielectric heating ability, plasticizing effect and solubilizing effect when facilitating amorphization. Then, the dissolution-mediated in situ amorphization mechanism was investigated and intuitively demonstrated. For the most promising formulation, i.e. microwaved systems with Korlliphor RH40 at 1.5 (w/w) plasticizer/polymer ratio, a complete and fast in vitro dissolution was observed relative to the untreated systems. In conclusion, non-ionic surfactants had the potential to facilitate microwave-induced in situ amorphization, which provided a new direction in the formulation designation for microwave-able systems.

Development of a multiparticulate drug delivery system for in situ amorphisation

In the current study, the concept of multiparticulate drug delivery systems (MDDS) was applied to tablets intended for the amorphisation of supersaturated granular ASDs in situ, i.e. amorphisation by microwave irradiation within the final dosage form. The MDDS concept was hypothesised to ensure geometric and structural stability of the dosage form and to improve the in vitro disintegration and dissolution characteristics. Granules were prepared in two sizes (small and large) containing the crystalline drug celecoxib (CCX) and polyvinylpyrrolidone/vinyl acetate copolymer (PVP/VA) at a 50 % w/w drug load as well as sodium dihydrogen phosphate monohydrate as the microwave absorbing excipient. The granules were subsequently embedded in an extra-granular tablet phase composed of either the filler microcrystalline cellulose (MCC) or mannitol (MAN), as well as the disintegrant crospovidone and the lubricant magnesium stearate. The tensile strength and disintegration time were investigated prior to and after 10 min of microwave irradiation (800 and 1000 W) and the formed ASDs were characterised by X-ray powder diffraction and modulated differential scanning calorimetry. Additionally, the internal structure was elucidated by X-ray micro-Computed Tomography (XµCT) and, finally, the dissolution performance of selected tablets was investigated. The MDDS tablets displayed no geometrical changes after microwave irradiation, however, the tensile strength and disintegration time increased. Complete amorphisation of CCX was achieved only for the MCC-based tablets at a power input of 1000 W, while MAN-based tablets displayed partial amorphisation independent of power input. The complete amorphisation of CCX was associated with the fusion of individual ASD granules within the tablets, which impacted the subsequent disintegration and dissolution performance. For these tablets, supersaturation was only observed after 60 min. On the other hand, the partially amorphised MDDS tablets displayed complete disintegration during the dissolution experiments, resulting in a fast onset of supersaturation within 5 min and an approx. 3.5-fold degree of supersaturation within the experimental timeframe (3 h). Overall, the MDDS concept was shown to potentially be a feasible dosage form for in situ amorphisation, however, there is still room for improvement to obtain a fully amorphous and disintegrating system.