Impacts of inoculum pre-treatments on enzyme activity and biochemical methane potential

Biogas from lignocellulosic feedstock: current status and challenges

The organic wastes and residues generated from agricultural, industrial, and domestic activities have the potential to be converted to bioenergy. One such energy is biogas, which has already been included in rural areas as an alternative cooking energy source and agricultural activities. It is produced via anaerobic digestion of a wide range of organic nutrient sources and is an essential renewable energy source. The factors influencing biogas yield, i.e., the various substrate, their characteristics, pretreatment methods involved, different microbial types, sources, and inoculum properties, are analyzed. Furthermore, the optimization of these parameters, along with fermentation media optimization, such as optimum pH, temperature, and anaerobic digestion strategies, is discussed. Novel approaches of bioaugmentation, co-digestion, phase separation, co-supplementation, nanotechnology, and biorefinery approach have also been explored for biogas production. Finally, the current challenges and prospects of the process are discussed in the review.

The importance of inspecting the inoculum's methane production for estimating kinetic parameters in biochemical methane potential tests

The aim of this study was to improve the quality of estimations of the first-order kinetic constant k, in Biochemical Methane Potential (BMP) tests. The results showed that existing guidelines for BMP tests are not sufficient to improve the estimation of k. The methane production of the inoculum itself exerted a major influence on the estimation of k. A flawed value in k was correlated with a high endogenous methane production. Excluding blanks that showed a distinct lag-phase of >1 day and a mean relative standard deviation >10% during the first ten days of a BMP test helped to retrieve more consistent estimates for k. For improving the repeatability in the determination of k in BMP tests, it is strongly recommended to inspect the methane production rate of the blanks. The proposed threshold values may be applied by other researchers but need further verification with different data.

Measurement of Biochemical Methane Potential of Heterogeneous Solid Substrates: Results of a Two-Phase French Inter-Laboratory Study

Biochemical methane potential (BMP) is essential to determine the production of methane for various substrates; literature shows important discrepancies for the same substrates. In this paper, a harmonized BMP protocol was developed and tested with two phases of BMP tests carried out by eleven French laboratories. Surprisingly, for the three same solid tested substrates (straw; raw mix and dried-shredded mix of potatoes, maize, beef meat and straw; and mayonnaise), the standard deviations of the repeatability and reproducibility inter-laboratory were not enhanced by the harmonized protocol (average of about 25% depending on the substrate), as compared to a previous step where all laboratories used their own protocols. Moreover, statistical analyses of all the results, after removal of the outliers (about 15% of all observations), did not highlight significant effect of the operational effect on BMP (stirring, automatic or manual gas quantification, use of trace metal, uses a bicarbonate buffer, inoculum to substrate ratio) at least for the tested ranges. On the other hand, the average intra-laboratory repeatability was low, about 7%, whatever the protocol, the substrate and the laboratory. It also appears that drying the SA substrate, which contained proteins, carbohydrates, lipids and fibers, does not impact its BMP.

Improving Inter-Laboratory Reproducibility in Measurement of Biochemical Methane Potential (BMP)

Biochemical methane potential (BMP) tests used to determine the ultimate methane yield of organic substrates are not sufficiently standardized to ensure reproducibility among laboratories. In this contribution, a standardized BMP protocol was tested in a large inter-laboratory project, and results were used to quantify sources of variability and to refine validation criteria designed to improve BMP reproducibility. Three sets of BMP tests were carried out by more than thirty laboratories from fourteen countries, using multiple measurement methods, resulting in more than 400 BMP values. Four complex but homogenous substrates were tested, and additionally, microcrystalline cellulose was used as a positive control. Inter-laboratory variability in reported BMP values was moderate. Relative standard deviation among laboratories (RSDR) was 7.5 to 24%, but relative range (RR) was 31 to 130%. Systematic biases were associated with both laboratories and tests within laboratories. Substrate volatile solids (VS) measurement and inoculum origin did not make major contributions to variability, but errors in data processing or data entry were important. There was evidence of negative biases in manual manometric and manual volumetric measurement methods. Still, much of the observed variation in BMP values was not clearly related to any of these factors and is probably the result of particular practices that vary among laboratories or even technicians. Based on analysis of calculated BMP values, a set of recommendations was developed, considering measurement, data processing, validation, and reporting. Recommended validation criteria are: (i) test duration at least 1% net 3 d, (ii) relative standard deviation for cellulose BMP not higher than 6%, and (iii) mean cellulose BMP between 340 and 395 NmLCH4 gVS−1. Evidence from this large dataset shows that following the recommendations—in particular, application of validation criteria—can substantially improve reproducibility, with RSDR < 8% and RR < 25% for all substrates. The cellulose BMP criterion was particularly important. Results show that is possible to measure very similar BMP values with different measurement methods, but to meet the recommended validation criteria, some laboratories must make changes to their BMP methods. To help improve the practice of BMP measurement, a new website with detailed, up-to-date guidance on BMP measurement and data processing was established.

Impact of Storage Conditions on the Methanogenic Activity of Anaerobic Digestion Inocula

The impact of storage temperature (4, 22 and 37 °C) and storage time (7, 14 and 21 days) on anaerobic digestion inocula was investigated through specific methanogenic activity assays. Experimental results showed that methanogenic activity decreased over time with storage, regardless of storage temperature. However, the rate at which the methanogenic activity decreased was two and five times slower at 4 °C than at 22 and 37 °C, respectively. The inoculum stored at 4 °C and room temperature (22 °C) maintained methanogenic activity close to that of fresh inoculum for 14 days (<10% difference). However, a storage temperature of 4 °C is preferred because of the slower decrease in activity with lengthier storage time. From this research, it was concluded that inoculum storage time should generally be kept to a minimum, but that storage at 4 °C could help maintain methanogenic activity for longer.

Multi-perspective analyses of rice straw modification by Pleurotus ostreatus and effects on biomethane production

Multi-perspective analyses were carried out to investigate the effect of rice straw modification for 45 days by P. ostreatus on biomethane of production. The results showed that rice straw modified for 25 days achieved the highest biomethane yield of 269 mL·g^-1 VS, which was a 26.9% improvement compared with non-modified rice straw. The multi-perspective analyses demonstrated that the improvement resulted from fungal enzymatic reactions, which led to changes in the physicochemical properties of rice straw. The porosity, surface area, acetyl group abundance, degree of polymerization, and lignin degradation selectivity of rice straw modified for 25 days were optimal for enzyme adsorption. Compared with non-modified rice straw, the adsorption of cellulase and xylanase on rice straw modified for 25 days was increased by 18.8% and 58.1%, respectively, which facilitated biomethane production. The study indicated that P. ostreatus is effective for improving biomethane production from rice straw.

Modification of corn stover for improving biodegradability and anaerobic digestion performance by Ceriporiopsis subvermispora

Ceriporiopsis subvermispora was used to modify corn stover for improving the biodegradability and biomethane yield. Corn stover was incubated with C. subvermispora for 5-90 days then anaerobically digested. It was found that the corn stover modified for 15 days achieved the highest biomethane yield of 235 mL·g^-1 VS, which was an increase of 15.2% over that of the non-modified one. The mechanism analyses indicated that the improvement resulted from the combined roles of degradation selectivity, destruction of lignocellulosic structures, and linkages. The analyses showed that C. subvermispora has a high relative selectivity of lignin degradation. The structure of the lignin and the linkages among lignin and hemicellulose and cellulose were broken obviously by acetyl group removal, and the enzymatic hydrolysis of cellulose was increased by 35.61%. The finding indicated that C. subvermispora modification is one of the effective methods for enhancing biomethane yield of corn stover.