Study of mesoporous catalysts for conversion of 2,3-butanediol to butenes

Prospects on bio-based 2,3-butanediol and acetoin production: Recent progress and advances

The bio-based platform chemicals 2,3-butanediol (BDO) and acetoin have various applications in chemical, cosmetics, food, agriculture, and pharmaceutical industries, whereas the derivatives of BDO could be used as fuel additives, polymer and synthetic rubber production. This review summarizes the novel technological developments in adapting genetic and metabolic engineering strategies for selection and construction of chassis strains for BDO and acetoin production. The valorization of renewable feedstocks and bioprocess development for the upstream and downstream stages of bio-based BDO and acetoin production are discussed. The techno-economic aspects evaluating the viability and industrial potential of bio-based BDO production are presented. The commercialization of bio-based BDO and acetoin production requires the utilization of crude renewable resources, the chassis strains with high fermentation production efficiencies and development of sustainable purification or conversion technologies.

Bio-Based Solvents and Gasoline Components From Renewable 2,3-Butanediol and 1,2-Propanediol: Synthesis and Characterization

In this study approaches for chemical conversions of the renewable compounds 1,2-propanediol (1,2-PD) and 2,3-butanediol (2,3-BD) that yield the corresponding cyclic ketals and glycol ethers have been investigated experimentally. The characterization of the obtained products as potential green solvents and gasoline components is discussed. Cyclic ketals have been obtained by the direct reaction of the diols with lower aliphatic ketones (1,2-PD + acetone → 2,2,4-trimethyl-1,3-dioxolane (TMD) and 2,3-BD + butanone-2 → 2-ethyl-2,4,5-trimethyl-1,3-dioxolane (ETMD)), for which the ΔH⁰_r, ΔS⁰_r and ΔG⁰_r values have been estimated experimentally. The monoethers of diols could be obtained through either hydrogenolysis of the pure ketals or from the ketone and the diol via reductive alkylation. In the both reactions, the cyclic ketals (TMD and ETMD) have been hydrogenated in nearly quantitative yields to the corresponding isopropoxypropanols (IPP) and 3-sec-butoxy-2-butanol (SBB) under mild conditions (T = 120-140 °C, p(H₂) = 40 bar) with high selectivity (>93%). Four products (TMD, ETMD, IPP and SBB) have been characterized as far as their physical properties are concerned (density, melting/boiling points, viscosity, calorific value, evaporation rate, Antoine equation coefficients), as well as their solvent ones (Kamlet-Taft solvatochromic parameters, miscibility, and polymer solubilization). In the investigation of gasoline blending properties, TMD, ETMD, IPP and SBB have shown remarkable antiknock performance with blending antiknock indices of 95.2, 92.7, 99.2 and 99.7 points, respectively.

Conversion of 5-Methyl-3-Heptanone to C8 Alkenes and Alkane over Bifunctional Catalysts

A one-step catalytic process was used to catalyze the hydrodeoxygenation of 5-methyl-3-heptanone (C8 ketone) to a mixture of 5-methyl-3-heptene, 5-methyl-2-heptene (C8 alkenes), and 3-methyl heptane (C8 alkane). High conversion of C8 ketone to the desired products was achieved over a single bed of a supported catalyst (bifunctional heterogeneous catalyst) consisting of one transition metal (copper (Cu) or platinum (Pt)) loaded on alumina (Al2O3) under mild operating conditions (reaction temperatures were varied between 180 °C to 260 °C, and the pressure was 1 atm). The C8 ketone was hydrogenated to 5-methyl-3-heptanol (C8 alcohol) over metal sites, followed by dehydration of the latter on acid sites on the support to obtain a mixture of C8 alkenes. These C8 alkenes can be further hydrogenated on metal sites to make a C8 alkane. The results showed that the main products over copper loaded on alumina (20 wt% Cu–Al2O3) were a mixture of C8 alkenes and C8 alkane in different amounts depending on the operating conditions (the highest selectivity for C8 alkenes (~82%) was obtained at 220 °C and a H2/C8 ketone molar ratio of 2). However, over platinum supported on alumina (1 wt% Pt–Al2O3), the major product was a C8 alkane with a selectivity up to 97% and a conversion of 99.9% at different temperatures and all H2/C8 ketone ratios.