The interplay between the suprafacial and intrafacial mechanisms for complete methane oxidation on substituted LaCoO3 perovskite oxides

Recent advances in abatement of methane and sulfur hexafluoride non-CO2 greenhouse gases under dual-carbon target

With the clarification of the CO2 abatement targets and pathways, the management and control of non-CO2 greenhouse gases (GHGs) have been widely emphasized. As the potent GHGs restricted by the Kyoto Protocol, methane (CH4) and sulfur hexafluoride (SF6) emissions contribute to a significant and increasing share of the total global GHG emissions, resulting in a continuous impact on the environment. Hence, the abatement of CH4 and SF6, the potent GHGs, is a matter of urgency. This paper focuses on recent advances in abatement of lean CH4 and SF6 waste gas. Firstly, a systematic review of abatement technologies for lean CH4 is presented, and two methods, namely, pressure swing adsorption and catalytic combustion, are emphasized. Additionally, the current status of four mainstream methods such as adsorption separation, thermal (catalytic) degradation, photocatalytic degradation, and non-thermal plasma degradation, as well as emerging technologies for SF6 abatement are summarized, and the inherent shortcomings and industrialization potentials of each technology are analyzed from multiple perspectives. This review demonstrates that, under dual-carbon target, existing abatement technologies are inadequate to meet the complex and diverse demands of the power and coal industries. There are many drawbacks for lean CH4 abatement technologies such as high investment in utilization devices, low processing capacity, high operating cost and requirement of high CH4 concentration. Degradation technologies for SF6 waste gas also suffer from low energy efficiency, high investment in catalytic degradation devices, and secondary pollution of degradation products. Based on this, two large-scale processing schemes with high feasibility are proposed. Finally, the current research hotspots, challenges, and future directions are put forward. This review aims to contribute some new perspectives to the abatement efforts of non-CO2 GHGs, so that the dual-carbon target can be realized as soon as possible.

Photodriven Methane Conversion on Transition Metal Oxide Catalyst: Recent Progress and Prospects

Methane as the main component in natural gas is a promising chemical raw material for synthesizing value-added chemicals, but its harsh chemical conversion process often causes severe energy and environment concerns. Photocatalysis provides an attractive path to active and convert methane into various products under mild conditions with clean and sustainable solar energy, although many challenges remain at present. In this review, recent advances in photocatalytic methane conversion are systematically summarized. As the basis of methane conversion, the activation of methane is first elucidated from the structural basis and activation path of methane molecules. The study is committed to categorizing and elucidating the research progress and the laws of the intricate methane conversion reactions according to the target products, including photocatalytic methane partial oxidation, reforming, coupling, combustion, and functionalization. Advanced photocatalytic reactor designs are also designed to enrich the options and reliability of photocatalytic methane conversion performance evaluation. The challenges and prospects of photocatalytic methane conversion are also discussed, which in turn offers guidelines for methane-conversion-related photocatalyst exploration, reaction mechanism investigation, and advanced photoreactor design.

Rational Atom Substitution to Obtain Efficient, Lead-Free Photocatalytic Perovskites Assisted by Machine Learning and DFT Calculations

Inorganic lead-free halide perovskites, devoid of toxic or rare elements, have garnered considerable attention as photocatalysts for pollution control, CO2 reduction and hydrogen production. In the extensive perovskite design space, factors like substitution or doping level profoundly impact their performance. To address this complexity, a synergistic combination of machine learning models and theoretical calculations were used to efficiently screen substitution elements that enhanced the photoactivity of substituted Cs2 AgBiBr6 perovskites. Machine learning models determined the importance of d10 orbitals, highlighting how substituent electron configuration affects electronic structure of Cs2 AgBiBr6 . Conspicuously, d10 -configured Zn2+ boosted the photoactivity of Cs2 AgBiBr6 . Experimental verification validated these model results, revealing a 13-fold increase in photocatalytic toluene conversion compared to the unsubstituted counterpart. This enhancement resulted from the small charge carrier effective mass, as well as the creation of shallow trap states, shifting the conduction band minimum, introducing electron-deficient Br, and altering the distance between the B-site cations d band centre and the halide anions p band centre, a parameter tuneable through d10 configuration substituents. This study exemplifies the application of computational modelling in photocatalyst design and elucidating structure-property relationships. It underscores the potential of synergistic integration of calculations, modelling, and experimental analysis across various applications.

Ultrasensitive electrochemiluminescence sensor for the detection of synthetic cannabinoids based on perovskite as coreaction accelerator and light-scattering effects of photonic crystals

As is common knowledge, a strong electrochemiluminescence (ECL) signal is required to ensure the high sensitivity of trace target detection. Here, a dual signal amplification strategy by integrating of perovskite and photonic crystal was fabricated for quantitative synthetic cannabinoids (AB-PINACA) detection based on Zr-connected PTCA and TCPP (PTCA-TCPP) with excellent ECL performance as luminophores. On the one hand, the co-reaction accelerator perovskite (LaCoO3) improved the effective electroactive area of the electrode and promoted the decomposition of K2S2O8, resulting in a stronger ECL signal value. On the other hand, polystyrene inverse opal (PIOPCs) formed after the swelling of PS microspheres not only taken advantage of the light scattering effect and excellent catalytic property of photonic crystals to amplify the ECL signal, but also could be used as a binder to fix LaCoO3 and PTCA-TCPP on the electrode surface to generate unprecedented ECL response and stable ECL signals. Subsequently, the detection substance AB-PINACA was loaded on the electrode surface via the amide bond with the luminophores PTCA-TCPP, thus quenching the ECL signal, so as to realize the sensitive detection of synthetic cannabinoids. Under the optimal conditions, the proposed sensor achieved highly sensitive AB-PINACA detection with a dynamic range from 1.0 × 10-12 to 1.0 × 10-3 g/L and the detection limit was 1.1 × 10-13 g/L, which had great application potential in the detection of synthetic cannabinoids.

Methane Oxidation over the Zeolites-Based Catalysts

Zeolites have ordered pore structures, good spatial constraints, and superior hydrothermal stability. In addition, the active metal elements inside and outside the zeolite framework provide the porous material with adjustable acid–base property and good redox performance. Thus, zeolites-based catalysts are more and more widely used in chemical industries. Combining the advantages of zeolites and active metal components, the zeolites-based materials are used to catalyze the oxidation of methane to produce various products, such as carbon dioxide, methanol, formaldehyde, formic acid, acetic acid, and etc. This multifunction, high selectivity, and good activity are the key factors that enable the zeolites-based catalysts to be used for methane activation and conversion. In this review article, we briefly introduce and discuss the effect of zeolite materials on the activation of C–H bonds in methane and the reaction mechanisms of complete methane oxidation and selective methane oxidation. Pd/zeolite is used for the complete oxidation of methane to carbon dioxide and water, and Fe- and Cu-zeolite catalysts are used for the partial oxidation of methane to methanol, formaldehyde, formic acid, and etc. The prospects and challenges of zeolite-based catalysts in the future research work and practical applications are also envisioned. We hope that the outcome of this review can stimulate more researchers to develop more effective zeolite-based catalysts for the complete or selective oxidation of methane.

Substitution of B-site in BaSb2O6 perovskite for surface lattice oxygen activation and boosted photocatalytic toluene mineralization

Perovskite oxides possess significant prospects in environment application because of their compositional versatility and controllable band structure for redox reactions. Nevertheless, low charge separation and limited reactants activation restrict their performance for practical applications. In this work, we reveal that the electronic structure of BaSb₂O₆ can be modulated effectively by substituting B-site cations, leading to broadened light response range and promoted carrier separation. The Ga atoms substitute the Sb atoms to form GaO bonds and enable octahedral distortion, resulting in the electron transfer from Ga atom to O atoms and realizing lattice oxygen activation. The unique electronic localization in the BaSb₂O₆ surface facilitates the adsorption and activation of O₂, H₂O, toluene and reaction intermediates, thus enhancing ROS generation for toluene mineralization. Compared with the performance of pure BaSb₂O₆, the photocatalytic toluene degradation and mineralization of 5 wt% Ga-BaSb₂O₆ are increased by 4.5 times and 4.8 times without obvious deactivation. The reported facile and valid strategy for in situ controlling of B-site in perovskite and their unique effects on the electronic structure would benefit the development of high-performance perovskites for environmental applications.

Activation of molecular oxygen over Mn-doped La2CuO4 perovskite for direct epoxidation of propylene

The synergetic interaction between manganese and copper in LaMn0.5Cu0.5O3 significantly promoted the epoxidation of propylene at lower temperature by converting the active sites from oxygen vacancies to Cu active sites of Cu–O–Mn.

Controlling lattice oxygen activity of oxygen carrier materials by design: a review and perspective

The lattice oxygen activity of oxygen carriers is critical to chemical looping processes and can be effectively controlled with prepared (i) solid solution mixtures, (ii) ternary oxide phases or (iii) core–shell structured oxygen carriers.