Occupational medicine implications of engineered nanoscale particulate matter

Estimating Occupational Exposure to VOCs, SVOCs, Particles and Participant Survey Reported Symptoms in Central Thailand Rice Farmers Using Multiple Sampling Techniques

Thailand is known for its agricultural productivity and rice exportation. Most farms use small machines and manual labor, creating potential exposure to multiple health hazards. A cross-sectional study was conducted to measure pollutants liberated during preparation, pesticide application, and harvesting. Thirty rice farmers, mostly males from 41 to 50 years old, participated. The participant survey data showed that 53.3% of the respondents spent >2 h per crop on preparation, <1 h on pesticide application, and about 1-2 h harvesting; 86.7% of the respondents maintained and stored mechanical applicators at home, suggesting possible after-work exposures. Gloves, fabric masks, boots, and hats were worn during all activities, and >90% wore long sleeved shirts and pants. VOCs and SVOCs were collected using charcoal tubes and solid phase micro sample extraction (SPME). An analysis of the charcoal and SPME samplers found that 30 compounds were detected overall and that 10 were in both the charcoal tubes and SPME samplers. The chemicals most often detected were 1, 1, 1 Trichloro ethane and xylene. Additionally, farmers experienced the highest exposure to particulates during harvesting. These results demonstrated that farmers experience multiple exposures while farming and that risk communication with education or training programs may mitigate exposure.

Fungal spores and pollen in particulate matter collected during agricultural activities in the Po Valley (Italy)

Airborne particulate matter (PM) containing fungal spores and pollen grains was sampled within a monitoring campaign of wheat threshing, plowing and sowing agricultural operations. Fungal spores and pollen grains were detected and identified on morphological basis. No studies were previously available about fungal spore and pollen content in agricultural PM in the Po Valley. Sampling was conducted in a Po Valley farmland in Mezzano (Ferrara, Italy). The organic particles collected were examined by scanning electron microscopy with energy dispersive X-ray spectrometer. Fungal spores and pollen grains were identified when possible at the level of species. The most frequent components of the organic particles sampled were spores of Aspergillus sp., which could represent a risk of developing allergies and aspergillosis for crop farmers.

Properties of agricultural aerosol released during wheat harvest threshing, plowing and sowing

This study shows for the first time a chemical and morphological characterization of agricultural aerosols released during three important agricultural operations: threshing, plowing and sowing. The field campaigns were carried out in the eastern part of the Po Valley, Italy, in summer and autumn 2009. The aerosol particles were sampled on quartz fiber filters and polytetrafluoroethylene membranes in order to allow Inductively Coupled Plasma Mass Spectrometry (ICP-MS) analysis and Scanning Electron Microscopy equipped with an Energy Dispersive X-ray Spectrometer (SEM-EDS) investigations, respectively. The organic carbon mass concentrations were measured with a Sunset Laboratory Dual-Optical Organic Carbone/Elemental Carbon (OCEC) Aerosol analyzer. The morphological and chemical analyses by SEM-EDS allowed recognizing four main particle classes: organic, silica, calcite and clay minerals. The organic particles contribute to both fine and coarse aerosol fractions up to ca. 50% for all three agricultural activities. This was also confirmed by OCEC analysis for fine fraction. Most of the agricultural aerosols, about 60%, were single particles and the remaining 40% were agglomerations of particles. The ICP-MS results showed that threshing and plowing produce more aerosol particles than sowing, which was characterized by important amounts of clay minerals produced from land soils.

Engineered nanomaterials: exposures, hazards, and risk prevention

Nanotechnology presents the possibility of revolutionizing many aspects of our lives. People in many settings (academic, small and large industrial, and the general public in industrialized nations) are either developing or using engineered nanomaterials (ENMs) or ENM-containing products. However, our understanding of the occupational, health and safety aspects of ENMs is still in its formative stage. A survey of the literature indicates the available information is incomplete, many of the early findings have not been independently verified, and some may have been over-interpreted. This review describes ENMs briefly, their application, the ENM workforce, the major routes of human exposure, some examples of uptake and adverse effects, what little has been reported on occupational exposure assessment, and approaches to minimize exposure and health hazards. These latter approaches include engineering controls such as fume hoods and personal protective equipment. Results showing the effectiveness - or lack thereof - of some of these controls are also included. This review is presented in the context of the Risk Assessment/Risk Management framework, as a paradigm to systematically work through issues regarding human health hazards of ENMs. Examples are discussed of current knowledge of nanoscale materials for each component of the Risk Assessment/Risk Management framework. Given the notable lack of information, current recommendations to minimize exposure and hazards are largely based on common sense, knowledge by analogy to ultrafine material toxicity, and general health and safety recommendations. This review may serve as an overview for health and safety personnel, management, and ENM workers to establish and maintain a safe work environment. Small start-up companies and research institutions with limited personnel or expertise in nanotechnology health and safety issues may find this review particularly useful.