Effect of the endothelial shear stress patterns on neointimal proliferation following drug-eluting bioresorbable vascular scaffold implantation: an optical coherence tomography study

Management of Coronary Vulnerable Plaque With Medical Therapy or Local Preventive Percutaneous Coronary Intervention

Acute coronary syndromes (ACS) often result from the rupture or erosion of high-risk coronary atherosclerotic plaques (ie, vulnerable plaques). Advances in intracoronary imaging such as intravascular ultrasound, optical coherence tomography, or near-infrared spectroscopy have improved the identification of vulnerable plaques, characterized by large plaque burden, small minimal luminal area, thin fibrous cap, and large lipid content. Although pharmacology, including lipid-lowering agents, and intensive risk-factor control are pivotal for management of vulnerable plaques and secondary prevention, recurrent events tend to accrue despite intensive pharmacotherapy. Therefore, it has been hypothesized that local preventive percutaneous coronary intervention may passivate these vulnerable plaques, preventing the occurrence of plaque-related ACS. However, solid evidence is lacking on its use for treatment of non-flow-limiting vulnerable plaques. As such, the optimal management of vulnerable plaques has not been established. Herein, we have reviewed the diagnosis and management of vulnerable plaques, focusing on systematic pharmacology and focal treatments.

Comparison of endothelial shear stress between ultrathin strut bioresorbable polymer drug-eluting stent vs durable-polymer drug-eluting stent post-stent implantation: An optical coherence tomography substudy from BIOFLOW II

BACKGROUND

Recent clinical data indicate a different performance of biodegradable polymer (BP)-drug eluting stent (DES) compared to durable polymer (DP)-DES. Whether this can be explained by a beneficial impact of BP-DES stent design on the local hemodynamic forces distribution remains unclear.

OBJECTIVES

To compare endothelial shear stress (ESS) distribution after implantation of ultrathin (us) BP-DES and DP-DES and examine the association between ESS and neointimal thickness (NIT) distribution in the two devices at 9 months follow up.

METHODS AND RESULTS

We retrospectively identified patients from the BIOFLOW II trial that had undergone OCT imaging. OCT data were utilized to reconstruct the surface of the stented segment at baseline and 9 months follow-up, simulate blood flow, and measure ESS and NIT in the stented segment. The patients were divided into 3 groups depending on whether DP-DES (N = 8, n = 56,160 sectors), BP-DES with a stent diameter of >3 mm (strut thickness of 80 μm, N = 6, n = 36,504 sectors), or BP-DES with a stent diameter of ≤3 mm (strut thickness of 60 μm, N = 8, n = 50,040 sectors) were used for treatment. The ESS, and NIT distribution and the association of these two variables were estimated and compared among the 3 groups.

RESULTS

In the DP-DES group mean NIT was 0.18 ± 0.17 mm and ESS 1.68 ± 1.66 Pa; for the BP-DES ≤3 mm group the NIT was 0.17 ± 0.11 mm and ESS 1.49 ± 1.24 Pa and for the BP-DES >3 mm group 0.20 ± 0.23 mm and 1.42 ± 1.24 Pa respectively (p < 0.001 for both NIT and ESS comparisons across groups). A negative correlation between NIT and baseline ESS was found, the correlation coefficient for all the stented segments was -0.33, p < 0.001.

CONCLUSION

In this OCT sub-study of the BIOFLOW II trial, the NIT was statistically different between groups of patients treated with BP-DES and DP-DES. In addition, regions of low ESS were associated with increased NIT in all studied devices.

Field-Induced Agglomerations of Polyethylene-Glycol-Functionalized Nanoclusters: Rheological Behaviour and Optical Microscopy

This research aims to investigate the agglomeration processes of magnetoresponsive functionalized nanocluster suspensions in a magnetic field, as well as how these structures impact the behaviour of these suspensions in biomedical applications. The synthesis, shape, colloidal stability, and magnetic characteristics of PEG-functionalized nanoclusters are described in this paper. Experiments using TEM, XPS, dynamic light scattering (DLS), VSM, and optical microscopy were performed to study chain-like agglomeration production and its influence on colloidal behaviour in physiologically relevant suspensions. The applied magnetic field aligns the magnetic moments of the nanoclusters. It provides an attraction between neighbouring particles, resulting in the formation of chains, linear aggregates, or agglomerates of clusters aligned along the applied field direction. Optical microscopy has been used to observe the creation of these aligned linear formations. The design of chain-like structures can cause considerable changes in the characteristics of ferrofluids, ranging from rheological differences to colloidal stability changes.

Rapid remodeling observed at mid-term in-vivo study of a smart reinforced acellular vascular graft implanted on a rat model

BACKGROUND

The poor performance of conventional techniques used in cardiovascular disease patients requiring hemodialysis or arterial bypass grafting has prompted tissue engineers to search for clinically appropriate off-the-shelf vascular grafts. Most patients with cardiovascular disease lack suitable autologous tissue because of age or previous surgery. Commercially available vascular grafts with diameters of < 5 mm often fail because of thrombosis and intimal hyperplasia.

RESULT

Here, we tested tubular biodegradable poly-e-caprolactone/polydioxanone (PCL/PDO) electrospun vascular grafts in a rat model of aortic interposition for up to 12 weeks. The grafts demonstrated excellent patency (100%) confirmed by Doppler Ultrasound, resisted aneurysmal dilation and intimal hyperplasia, and yielded neoarteries largely free of foreign materials. At 12 weeks, the grafts resembled native arteries with confluent endothelium, synchronous pulsation, a contractile smooth muscle layer, and co-expression of various extracellular matrix components (elastin, collagen, and glycosaminoglycan).

CONCLUSIONS

The structural and functional properties comparable to native vessels observed in the neoartery indicate their potential application as an alternative for the replacement of damaged small-diameter grafts. This synthetic off-the-shelf device may be suitable for patients without autologous vessels. However, for clinical application of these grafts, long-term studies (> 1.5 years) in large animals with a vasculature similar to humans are needed.

Morphological and Physiological Characteristics of Ruptured Plaques in Native Arteries and Neoatherosclerotic Segments: An OCT-Based and Computational Fluid Dynamics Study

Background

Intravascular imaging has been used to assess the morphology of lesions causing an acute coronary syndrome (ACS) in native vessels (NV) and identify differences between plaques that ruptured (PR) and caused an event and those that ruptured without clinical manifestations. However, there is no data about the morphological and physiological characteristics of neoatherosclerotic plaques that ruptured (PR-NA) which constitute a common cause of stent failure.

Methods

We retrospectively analyzed data from patients admitted with an acute myocardial infarction that had optical coherence tomography (OCT) imaging of the culprit vessel before balloon pre-dilation. OCT pullbacks showing PR were segmented at every 0.4 mm. The extent of the formed cavity, lipid and calcific tissue, thrombus, and macrophages were measured, and the fibrous cap thickness (FCT) and the incidence of micro-channels and cholesterol crystals were reported. These data were used to reconstruct a representative model of the native and neoatherosclerotic lesion geometry that was processed with computational fluid dynamics (CFD) techniques to estimate the distribution of the endothelial shear stress and plaque structural stress.

Result

Eighty patients were included in the present analysis: 56 had PR in NV (PR-NV group) and 24 in NA segments (PR-NA group). The PR-NV group had a larger minimum lumen area (2.93 ± 2.03 vs. 2.00 ± 1.26 mm², p = 0.015) but similar lesion length and area stenosis compared to PR-NA group. The mean FCT (186 ± 65 vs. 232 ± 80 μm, p = 0.009) and the lipid index was smaller (16.7 ± 13.8 vs. 25.9 ± 14.1, p = 0.008) while the of calcific index (8.3 ± 9.5 vs. 2.2 ± 1.6%, p = 0.002) and the incidence of micro-channels (41.4 vs. 12.5%, p = 0.013) was higher in the PR-NV group. Conversely, there was no difference in the incidence of cholesterol crystals, thrombus burden or the location of the rupture site between groups. CFD analysis revealed higher maximum endothelial shear stress (19.1 vs. 11.0 Pa) and lower maximum plaque structural stress (38.8 vs. 95.1 kPa) in the PR-NA compared to the PR-NV model.

Conclusion

We reported significant morphological and physiological differences between culprit ruptured plaques in native and stented segments. Further research is needed to better understand the causes of these differences and the mechanisms regulating neoatherosclerotic lesion destabilization.

Effects of aggressive predilatation, sizing, and postdilatation strategy for coronary bioresorbable vascular scaffolds implantation

BACKGROUND

The results of the recent Amsterdam Investigator-Initiated Absorb Strategy All-Comers trial showed that the predilatation, sizing, and postdilatation (PSP) technique did not lower the long-term rates of scaffold thrombosis and adverse events. We evaluated the impact of aggressive PSP bioresorbable vascular scaffold (BRS) implantation on the short- and long-term clinical outcomes.

METHODS

From June 2014 to December 2016, 150 patients with BRS implantation were enrolled and received successful percutaneous coronary intervention (PCI), of whom 104 received aggressive PSP technique (high-pressure predilatation and lesion preparation in addition to the traditional PSP technique). Short- and long-term outcomes were compared.

RESULTS

All patients underwent successful PCI and BRS implantation with final Thrombolysis in Myocardial Infarction grade 3 flow. The baseline and procedure characteristics were similar in both groups. Debulking techniques were used in 13 (8.7%) patients. Intracoronary imaging modalities were used in 73 (48.7%) patients. After BRS implantation, no adverse events were observed within 30 days in both groups. During the mean follow-up period of 2.98 ± 0.77 years, 12 (8.0%) patients experienced major adverse cardiovascular events (MACEs), including one cardiovascular death (0.6%), three nonfatal myocardial infarction (2.0 %), and 11 target-vessel revascularization (7.3 %). Multivariate Cox regression analysis showed that aggressive PSP remained an independent protective factor for MACEs. Moreover, the use of intracoronary imaging and rotablation atherectomy was associated with better clinical outcomes.

CONCLUSION

Lesion preparation by aggressive PSP in BRS implantation was associated with better long-term clinical outcomes.

Hangover after Side Branch Stenting: The Discomfort Comes Afterwards

The authors report on a patient with recurrent angina at rest and on exertion 2 years after percutaneous revascularisation of the first diagonal branch (D1). Invasive coronary angiography with full functional testing was planned with the tentative diagnosis of coronary vascular dysfunction. Coronary angiography with functional testing revealed a haemodynamically significant intermediate stenosis at the D1-left anterior descending artery bifurcation. Optical coherence tomography demonstrated neointimal bridging and accelerated downstream atherosclerosis that was induced by protrusion of the previously implanted stent into the main branch. Although the overhanging stent was considered insignificant at first, it caused significant discomfort after 2 years. After provisional stenting of the main branch with crushing of the protruding stent and continuous medical treatment, the patient remained free of recurrent angina.

The Development of Design and Manufacture Techniques for Bioresorbable Coronary Artery Stents

Coronary artery disease (CAD) is the leading killer of humans worldwide. Bioresorbable polymeric stents have attracted a great deal of interest because they can treat CAD without producing long-term complications. Bioresorbable polymeric stents (BMSs) have undergone a sustainable revolution in terms of material processing, mechanical performance, biodegradability and manufacture techniques. Biodegradable polymers and copolymers have been widely studied as potential material candidates for bioresorbable stents. It is a great challenge to find a reasonable balance between the mechanical properties and degradation behavior of bioresorbable polymeric stents. Surface modification and drug-coating methods are generally used to improve biocompatibility and drug loading performance, which are decisive factors for the safety and efficacy of bioresorbable stents. Traditional stent manufacture techniques include etching, micro-electro discharge machining, electroforming, die-casting and laser cutting. The rapid development of 3D printing has brought continuous innovation and the wide application of biodegradable materials, which provides a novel technique for the additive manufacture of bioresorbable stents. This review aims to describe the problems regarding and the achievements of biodegradable stents from their birth to the present and discuss potential difficulties and challenges in the future.

The impact of plaque type on strut embedment/protrusion and shear stress distribution in bioresorbable scaffold

AIMS

Scaffold design and plaque characteristics influence implantation outcomes and local flow dynamics in treated coronary segments. Our aim is to assess the impact of strut embedment/protrusion of bioresorbable scaffold on local shear stress distribution in different atherosclerotic plaque types.

METHODS AND RESULTS

Fifteen Absorb everolimus-eluting Bioresorbable Vascular Scaffolds were implanted in human epicardial coronary arteries. Optical coherence tomography (OCT) was performed post-scaffold implantation and strut embedment/protrusion were analysed using a dedicated software. OCT data were fused with angiography to reconstruct 3D coronary anatomy. Blood flow simulation was performed and wall shear stress (WSS) was estimated in each scaffolded surface and the relationship between strut embedment/protrusion and WSS was evaluated. There were 9083 struts analysed. Ninety-seven percent of the struts (n = 8840) were well-apposed and 243 (3%) were malapposed. At cross-section level (n = 1289), strut embedment was significantly increased in fibroatheromatous plaques (76 ± 48 µm) and decreased in fibrocalcific plaques (35 ± 52 µm). Compatible with strut embedment, WSS was significantly higher in lipid-rich fibroatheromatous plaques (1.50 ± 0.81 Pa), whereas significantly decreased in fibrocalcified plaques (1.05 ± 0.91 Pa). After categorization of WSS as low (<1.0 Pa) and normal/high WSS (≥1.0 Pa), the percent of low WSS in the plaque subgroups were 30.1%, 31.1%, 25.4%, and 36.2% for non-diseased vessel wall, fibrous plaque, fibroatheromatous plaque, and fibrocalcific plaque, respectively (P-overall < 0.001).

CONCLUSION

The composition of the underlying plaque influences strut embedment which seems to have effect on WSS. The struts deeply embedded in lipid-rich fibroatheromas plaques resulted in higher WSS compared with the other plaque types.

Impact of Endothelial Shear Stress on Absorption Process of Resorbable Magnesium Scaffold: A BIOSOLVE-II Substudy

BACKGROUND/PURPOSE

Local hemodynamic forces such as endothelial shear stress (ESS) may have an influence on appropriate neointimal healing, vessel remodeling, and struts' absorption process following second-generation drug-eluting resorbable magnesium scaffold (RMS, Magmaris, Biotronik AG, Buelach, Switzerland) placement. The aim of this study was to investigate the impact of ESS assessed by optical coherence tomography (OCT)-based computational fluid dynamic (CFD) simulations on absorption process and coronary lumen dimension after Magmaris implantation.

METHODS AND RESULTS

A total of 22 patients who were enrolled in the BIOSOLVE-II trial and underwent serial OCT assessment immediately after Magmaris implantation and at 6- and 12-month follow-up were included. We evaluated qualitative OCT findings frame by frame, and CFD simulations were performed to calculate the ESS at 3-dimensional (3D) reconstructed arteries. For quantitative calculation, the average ESS within each 1-mm section was classified into three groups: low (<1.0 Pa), intermediate (1.0-2.5 Pa), or high (>2.5 Pa). A significant difference of percentage remnants of scaffold was observed among the 3 groups at 12-month follow-up (P = 0.001) but not at 6-month follow-up. Low-ESS segment at baseline resulted in a greater lumen change of -1.857 ± 1.902 mm² at 1 year compared to -1.277 ± 1.562 mm² in the intermediate-ESS segment (P = 0.017) and - 0.709 ± 1.213 mm² in the high-ESS segment (P = 0.001).

CONCLUSION

After Magmaris implantation, the presence of higher ESS might be associated with slower strut absorption process but less luminal loss.

Neointimal hyperplasia of ultra-thin stents with microcrystalline sirolimus or durable polymer everolimus-eluting stents: 6- and 24-month results of the DESSOLVE III OCT study

AIMS

The DESSOLVE III OCT substudy aimed to compare serially neointimal hyperplasia volume obstruction (%VO) between the thin-strut MiStent with early polymer elimination and nine-month sustained drug release from microcrystalline sirolimus and the durable polymer-coated everolimus-eluting XIENCE stent at six and 24 months after implantation.

METHODS AND RESULTS

The efficacy endpoint was %VO, calculated as abluminal neointimal volume/stent volume. Thirty-six patients (MiStent 16 patients, 16 lesions; XIENCE 20 patients, 22 lesions) underwent serial OCT evaluation at both six and 24 months. At six months, mean abluminal %VO was significantly lower in the MiStent group than in the XIENCE group (14.54±3.70% vs 19.11±6.70%; p=0.011), whereas the difference in %VO between the two groups decreased at 24 months (20.88±5.72% vs 23.50±7.33%; p=0.24). There was no significant difference in percentage malapposed struts and percentage uncovered struts between the two groups at both time points.

CONCLUSIONS

In the serial comparative OCT analysis of the MiStent versus the XIENCE, the MiStent showed a more favourable efficacy for preventing neointimal formation with comparable strut tissue coverage, as compared with the XIENCE at six months, but this difference in %VO decreased at 24 months so that the difference in neointima at 24 months was no longer significant.

Bioresorbable vascular scaffolds versus everolimus-eluting stents: a biomechanical analysis of the ABSORB III Imaging substudy

AIMS

The Absorb bioresorbable vascular scaffold (BVS) has high rates of target lesion failure (TLF) at three years. Low wall shear stress (WSS) promotes several mechanisms related to device TLF. We investigated the impact of BVS compared to XIENCE V (XV) on coronary WSS after device deployment.

METHODS AND RESULTS

In the prospective, randomised, controlled ABSORB III Imaging study (BVS [n=77] or XV [n=36]), computational fluid dynamics were performed on fused angiographic and intravascular ultrasound (IVUS) images of post-implanted vessels. Low WSS was defined as <1 Pa. There were no differences in demographics, clinical risks, angiographic reference vessel diameter or IVUS minimal lumen diameter between BVS and XV patients. A greater proportion of vessels treated with BVS compared to XV demonstrated low WSS across the whole device (BVS: 17/77 [22%] vs XV: 2/36 [6%], p<0.029). Compared to XV, BVS demonstrated lower median circumferential WSS (1.73 vs 2.21 Pa; p=0.036), outer curvature WSS (p=0.026), and inner curvature WSS (p=0.038). Similarly, BVS had lower proximal third WSS (p=0.024), middle third WSS (p=0.047) and distal third WSS (p=0.028) when compared to XV. In a univariable logistic regression analysis, patients who received BVS were 4.8 times more likely to demonstrate low WSS across the scaffold/stent when compared to XV patients. Importantly, in a multivariable linear regression model, hypertension (beta: 0.186, p=0.023), lower contrast frame count velocity (beta: -0.411, p<0.001), lower post-stent residual plaque burden (beta: -0.338, p<0.001), lower % underexpanded frames (beta: -0.170, p=0.033) and BVS deployment (beta: 0.251, p=0.002) remained independently associated with a greater percentage of stented coronary vessel areas exposed to low WSS.

CONCLUSIONS

In this randomised controlled study, the Absorb BVS was 4.8 times more likely than the XV metallic stent to demonstrate low WSS. BVS implantation, lower blood velocity and lower residual post-stent plaque burden were independently associated with greater area of low WSS.

Transcatheter-Delivered Expandable Bioresorbable Polymeric Graft With Stenting Capacity Induces Vascular Regeneration

•

We designed a transcatheter balloon-expandable resorbable vascular graft with support capacity.

•

After 2 months in vivo, grafts show native-like tissue reconstruction with endoluminal elastin.

•

The concept convenes regenerative grafting, minimally invasive delivery, and clinical stenting.

As the next step in the translation of vascular tissue engineering, this study uniquely combines transcatheter delivery and in situ tissue regeneration using a novel bioresorbable electrospun polymer graft that can be implanted minimally invasively. Once delivered inside a small-diameter vessel, the electrospun microstructure supports the vessel wall, facilitates cellular infiltration, and guides organized tissue formation.

Percutaneous Coronary Intervention for Vulnerable Coronary Atherosclerotic Plaque

BACKGROUND

Acute coronary syndromes most commonly arise from thrombosis of lipid-rich coronary atheromas that have large plaque burden despite angiographically appearing mild.

OBJECTIVES

This study sought to examine the outcomes of percutaneous coronary intervention (PCI) of non-flow-limiting vulnerable plaques.

METHODS

Three-vessel imaging was performed with a combination intravascular ultrasound (IVUS) and near-infrared spectroscopy (NIRS) catheter after successful PCI of all flow-limiting coronary lesions in 898 patients presenting with myocardial infarction (MI). Patients with an angiographically nonobstructive stenosis not intended for PCI but with IVUS plaque burden of ≥65% were randomized to treatment of the lesion with a bioresorbable vascular scaffold (BVS) plus guideline-directed medical therapy (GDMT) versus GDMT alone. The primary powered effectiveness endpoint was the IVUS-derived minimum lumen area (MLA) at protocol-driven 25-month follow-up. The primary (nonpowered) safety endpoint was randomized target lesion failure (cardiac death, target vessel-related MI, or clinically driven target lesion revascularization) at 24 months. The secondary (nonpowered) clinical effectiveness endpoint was randomized lesion-related major adverse cardiac events (cardiac death, MI, unstable angina, or progressive angina) at latest follow-up.

RESULTS

A total of 182 patients were randomized (93 BVS, 89 GDMT alone) at 15 centers. The median angiographic diameter stenosis of the randomized lesions was 41.6%; by near-infrared spectroscopy-IVUS, the median plaque burden was 73.7%, the median MLA was 2.9 mm², and the median maximum lipid plaque content was 33.4%. Angiographic follow-up at 25 months was completed in 167 patients (91.8%), and the median clinical follow-up was 4.1 years. The follow-up MLA in BVS-treated lesions was 6.9 ± 2.6 mm² compared with 3.0 ± 1.0 mm² in GDMT alone-treated lesions (least square means difference: 3.9 mm²; 95% confidence interval: 3.3 to 4.5; p < 0.0001). Target lesion failure at 24 months occurred in similar rates of BVS-treated and GDMT alone-treated patients (4.3% vs. 4.5%; p = 0.96). Randomized lesion-related major adverse cardiac events occurred in 4.3% of BVS-treated patients versus 10.7% of GDMT alone-treated patients (odds ratio: 0.38; 95% confidence interval: 0.11 to 1.28; p = 0.12).

CONCLUSIONS

PCI of angiographically mild lesions with large plaque burden was safe, substantially enlarged the follow-up MLA, and was associated with favorable long-term clinical outcomes, warranting the performance of an adequately powered randomized trial. (PROSPECT ABSORB [Providing Regional Observations to Study Predictors of Events in the Coronary Tree II Combined with a Randomized, Controlled, Intervention Trial]; NCT02171065).

Preclinical evaluation of a thin-strut bioresorbable scaffold (ArterioSorb): acute-phase invasive imaging assessment and hemodynamic implication

AIMS

The aim of this study was to assess the acute performance of the 95 µm ArterioSorb oriented poly L-lactic acid (PLLA) scaffold in comparison with the XIENCE metallic drug-eluting stent (DES) in porcine coronary arteries.

METHODS AND RESULTS

In 15 non-atherosclerotic Yucatan mini pigs, the ArterioSorb (3.0/14 mm) and XIENCE (3.0/15 mm) were implanted in 25 and 15 vessels, respectively. Acute performance was evaluated by using quantitative coronary angiography (QCA) and optical coherence tomography (OCT). Following three-dimensional reconstruction of the coronary arteries, endothelial shear stress (ESS) was quantified using non-Newtonian steady-flow simulation. Acute recoil measured by QCA was comparable in the two arms. Post-procedural flow and scaffold/stent area by OCT did not differ between the two devices. ESS post procedure was comparable between ArterioSorb and XIENCE (2.21±1.97 vs 2.25±1.71 Pa, p=0.314).

CONCLUSIONS

Acute recoil, luminal dimensions and ESS in the ArterioSorb oriented PLLA scaffold with thin struts of 95 µm were comparable to those in the XIENCE metallic DES.

Procedural microvascular activation in long lesions treated with bioresorbable vascular scaffolds or everolimus-eluting stents: the PROACTIVE trial

AIMS

Significant platelet activation after long stented coronary segments has been associated with periprocedural microvascular impairment and myonecrosis. In long lesions treated either with an everolimus-eluting bioresorbable vascular scaffold (BVS) or an everolimus-eluting stent (EES), we aimed to investigate (a) procedure-related microvascular impairment, and (b) the relationship of platelet activation with microvascular function and related myonecrosis.

METHODS AND RESULTS

Patients (n=66) undergoing elective percutaneous coronary intervention (PCI) in long lesions were randomised 1:1 to either BVS or EES. The primary endpoint was the difference between groups in changes of pressure-derived corrected index of microvascular resistance (cIMR) after PCI. Periprocedural myonecrosis was assessed by high-sensitivity cardiac troponin T (hs-cTnT), platelet reactivity by high-sensitivity adenosine diphosphate (hs-ADP)-induced platelet reactivity with the Multiplate Analyzer. Post-dilatation was more frequent in the BVS group, with consequent longer procedure time. A significant difference was observed between the two groups in the primary endpoint of ΔcIMR (p=0.04). hs-ADP was not different between the groups at different time points. hs-cTnT significantly increased after PCI, without difference between the groups.

CONCLUSIONS

In long lesions, BVS implantation is associated with significant acute reduction in IMR as compared with EES, with no significant interaction with platelet reactivity or periprocedural myonecrosis.

Recent Advances in Manufacturing Innovative Stents

Cardiovascular diseases are the most distributed cause of death worldwide. Stenting of arteries as a percutaneous transluminal angioplasty procedure became a promising minimally invasive therapy based on re-opening narrowed arteries by stent insertion. In order to improve and optimize this method, many research groups are focusing on designing new or improving existent stents. Since the beginning of the stent development in 1986, starting with bare-metal stents (BMS), these devices have been continuously enhanced by applying new materials, developing stent coatings based on inorganic and organic compounds including drugs, nanoparticles or biological components such as genes and cells, as well as adapting stent designs with different fabrication technologies. Drug eluting stents (DES) have been developed to overcome the main shortcomings of BMS or coated stents. Coatings are mainly applied to control biocompatibility, degradation rate, protein adsorption, and allow adequate endothelialization in order to ensure better clinical outcome of BMS, reducing restenosis and thrombosis. As coating materials (i) organic polymers: polyurethanes, poly(ε-caprolactone), styrene-b-isobutylene-b-styrene, polyhydroxybutyrates, poly(lactide-co-glycolide), and phosphoryl choline; (ii) biological components: vascular endothelial growth factor (VEGF) and anti-CD34 antibody and (iii) inorganic coatings: noble metals, wide class of oxides, nitrides, silicide and carbide, hydroxyapatite, diamond-like carbon, and others are used. DES were developed to reduce the tissue hyperplasia and in-stent restenosis utilizing antiproliferative substances like paclitaxel, limus (siro-, zotaro-, evero-, bio-, amphi-, tacro-limus), ABT-578, tyrphostin AGL-2043, genes, etc. The innovative solutions aim at overcoming the main limitations of the stent technology, such as in-stent restenosis and stent thrombosis, while maintaining the prime requirements on biocompatibility, biodegradability, and mechanical behavior. This paper provides an overview of the existing stent types, their functionality, materials, and manufacturing conditions demonstrating the still huge potential for the development of promising stent solutions.

Histopathologic and physiologic effect of bifurcation stenting: current status and future prospects

Introduction: Coronary bifurcation lesions are involved in up to 20% of all percutaneous coronary interventions (PCI). However, bifurcation lesion intervention is associated with a high complication rate, and optimal treatment of coronary bifurcation is an ongoing debate.Areas covered: Both different stenting techniques and a variety of devices have been suggested for bifurcation treatment, including the use of conventional coronary stents, bioresorbable vascular scaffolds (BVS), drug-eluting balloons (DEB), and stents dedicated to bifurcations. This review will summarize different therapeutic approaches with their advantages and shortcomings, with special emphasis on histopathologic and physiologic effects of each treatment strategy.Expert opinion: Histopathology and clinical data have shown that a more simple treatment strategy is beneficial in bifurcation lesions, achieving superior results. Bifurcation interventions through balloon angioplasty or placement of stents can importantly alter the bifurcation's geometry and accordingly modify local flow conditions. Computational fluid dynamics (CFD) studies have shown that the outcome of bifurcation interventions is governed by local hemodynamic shear conditions. Minimizing detrimental flow conditions as much as possible should be the ultimate strategy to achieve long-term success of bifurcation interventions.

Location-Specific Comparison Between a 3D In-Stent Restenosis Model and Micro-CT and Histology Data from Porcine In Vivo Experiments

BACKGROUND

Coronary artery restenosis is an important side effect of percutaneous coronary intervention. Computational models can be used to better understand this process. We report on an approach for validation of an in silico 3D model of in-stent restenosis in porcine coronary arteries and illustrate this approach by comparing the modelling results to in vivo data for 14 and 28 days post-stenting.

METHODS

This multiscale model includes single-scale models for stent deployment, blood flow and tissue growth in the stented vessel, including smooth muscle cell (SMC) proliferation and extracellular matrix (ECM) production. The validation procedure uses data from porcine in vivo experiments, by simulating stent deployment using stent geometry obtained from micro computed tomography (micro-CT) of the stented vessel and directly comparing the simulation results of neointimal growth to histological sections taken at the same locations.

RESULTS

Metrics for comparison are per-strut neointimal thickness and per-section neointimal area. The neointimal area predicted by the model demonstrates a good agreement with the detailed experimental data. For 14 days post-stenting the relative neointimal area, averaged over all vessel sections considered, was 20 ± 3% in vivo and 22 ± 4% in silico. For 28 days, the area was 42 ± 3% in vivo and 41 ± 3% in silico.

CONCLUSIONS

The approach presented here provides a very detailed, location-specific, validation methodology for in silico restenosis models. The model was able to closely match both histology datasets with a single set of parameters. Good agreement was obtained for both the overall amount of neointima produced and the local distribution. It should be noted that including vessel curvature and ECM production in the model was paramount to obtain a good agreement with the experimental data.

Endothelial shear stress 5 years after implantation of a coronary bioresorbable scaffold

Aims

As a sine qua non for arterial wall physiology, local hemodynamic forces such as endothelial shear stress (ESS) may influence long-term vessel changes as bioabsorbable scaffolds dissolve. The aim of this study was to perform serial computational fluid dynamic (CFD) simulations to examine immediate and long-term haemodynamic and vascular changes following bioresorbable scaffold placement.

Methods and results

Coronary arterial models with long-term serial assessment (baseline and 5 years) were reconstructed through fusion of intravascular optical coherence tomography and angiography. Pulsatile non-Newtonian CFD simulations were performed to calculate the ESS and relative blood viscosity. Time-averaged, systolic, and diastolic results were compared between follow-ups. Seven patients (seven lesions) were included in this analysis. A marked heterogeneity in ESS and localised regions of high blood viscosity were observed post-implantation. Percent vessel area exposed to low averaged ESS (<1 Pa) significantly decreased over 5 years (15.92% vs. 4.99%, P < 0.0001) whereas moderate (1-7 Pa) and high ESS (>7 Pa) did not significantly change (moderate ESS: 76.93% vs. 80.7%, P = 0.546; high ESS: 7.15% vs. 14.31%, P = 0.281), leading to higher ESS at follow-up. A positive correlation was observed between baseline ESS and change in lumen area at 5 years (P < 0.0001). Maximum blood viscosity significantly decreased over 5 years (4.30 ± 1.54 vs. 3.21± 0.57, P = 0.028).

Conclusion

Immediately after scaffold implantation, coronary arteries demonstrate an alternans of extremely low and high ESS values and localized areas of high blood viscosity. These initial local haemodynamic disturbances may trigger fibrin deposition and thrombosis. Also, low ESS can promote neointimal hyperplasia, but may also contribute to appropriate scaffold healing with normalisation of ESS and reduction in peak blood viscosity by 5 years.

Effects of local hemodynamics and plaque characteristics on neointimal response following bioresorbable scaffolds implantation in coronary bifurcations

Heterogeneous neointimal response has been observed after implantation of all generations of coronary stents. Our aim was assessing local factors of shear stress (SS) and plaque characteristics in neointimal response after implantation of bioresorbable scaffolds (BRS) in bifurcations. Ten patients from the BIFSORB pilot study were analysed. Follow-up optical frequency domain imaging (OFDI) was performed at 1 month and 2 years. Coronary lumen and BRS structure were reconstructed by fusion of OFDI and angiography and were used for subsequent flow simulation. Plaque arc degree and SS were quantified using post-procedural OFDI data and were matched with follow-up OFDI using anatomical landmarks. Strut-level and segment-level analysis were performed for 1-month and 2-year follow-up respectively. A total of 444 struts (54 jailing struts) were included at 1-month follow-up. Time-average SS (TASS) was significantly lower for covered struts than for uncovered struts in non-bifurcation segments (TASS: 1.81 ± 1.87 vs. 3.88 ± 3.72 Pa, p < 0.001). The trend remained the same for jailing struts, although statistically insignificant (TASS: 10.85 ± 13.12 vs. 13.64 ± 14.48 Pa, p = 0.328). For 2-year follow-up, a total of 66 sub-regions were analysed. Neointimal hyperplasia area (NTA) was negatively correlated with TASS in core-segments (ρ = - 0.389, p = 0.037) and positively correlated with plaque arc degree in non-core segments (ρ = 0.387, p = 0.018). Slightly stronger correlations with NTA were observed when combining TASS and plaque arc degree in both core segments (ρ = - 0.412, p = 0.026) and non-core segments (ρ = - 0.395, p = 0.015). Hemodynamic microenvironment and baseline plaque characteristics may regulate neointimal response after BRS implantation in bifurcation. These findings underline the combined role of plaque characteristics and local hemodynamics in vessel healing after stent implantation.

Impact of strut dimensions and vessel caliber on thrombosis risk of bioresorbable scaffolds using hemodynamic metrics

Bioresorbable scaffolds (BRS) promise to be the treatment of choice for stenosed coronary vessels. But higher thrombosis risk found in current clinical studies limits the expectations. Three hemodynamic metrics are introduced to evaluate the thrombosis risk of coronary stents/scaffolds using transient computational fluid dynamics (CFD). The principal phenomena are platelet activation and effective diffusion (platelet shear number, PSN), convective platelet transport (platelet convection number, PCN) and platelet aggregation (platelet aggregation number, PAN) were taken into consideration. In the present study, two different stent designs (thick-strut vs. thin-strut design) positioned in small- and medium-sized vessels (reference vessel diameter, RVD=2.25 mm vs. 2.70 mm) were analyzed. In both vessel models, the thick-strut design induced higher PSN, PCN and PAN values than the thin-strut design (thick-strut vs. thin-strut: PSN=2.92/2.19 and 0.54/0.30; PCN=3.14/1.15 and 2.08/0.43; PAN: 14.76/8.19 and 20.03/10.18 for RVD=2.25 mm and 2.70 mm). PSN and PCN are increased by the reduction of the vessel size (PSN: RVD=2.25 mm vs. 2.70 mm=5.41 and 7.30; PCN: RVD=2.25 mm vs. 2.70 mm=1.51 and 2.67 for thick-strut and thin-strut designs). The results suggest that bulky stents implanted in small caliber vessels may substantially increase the thrombosis risk. Moreover, sensitivity analyses imply that PSN is mostly influenced by vessel size (lesion-related factor), whereas PCN and PAN sensitively respond to strut-thickness (device-related factor).

Computational modelling of magnesium stent mechanical performance in a remodelling artery: Effects of multiple remodelling stimuli

Significant research has been conducted in the area of coronary stents/scaffolds made from resorbable metallic and polymeric biomaterials. These next-generation bioabsorbable stents have the potential to completely revolutionise the treatment of coronary artery disease. The primary advantage of resorbable devices over permanent stents is their temporary presence which, from a theoretical point of view, means only a healed coronary artery will be left behind following degradation of the stent potentially eliminating long-term clinical problems associated with permanent stents. The healing of the artery following coronary stent/scaffold implantation is crucial for the long-term safety of these devices. Computational modelling can be used to evaluate the performance of complex stent devices in silico and assist in the design and development and understanding of the next-generation resorbable stents. What is lacking in computational modelling literature is the representation of the active response of the arterial tissue in the weeks and months following stent implantation, ie, neointimal remodelling, in particular for the case of biodegradable stents. In this paper, a computational modelling framework is developed, which accounts for two major physiological stimuli responsible for neointimal remodelling and combined with a magnesium corrosion model that is capable of simulating localised pitting (realistic) stent corrosion. The framework is used to simulate different neointimal growth patterns and to explore the effects the neointimal remodelling has on the mechanical performance (scaffolding support) of the bioabsorbable magnesium stent.

Angiographic derived endothelial shear stress: a new predictor of atherosclerotic disease progression

AIMS

To examine the efficacy of angiography derived endothelial shear stress (ESS) in predicting atherosclerotic disease progression.

METHODS AND RESULTS

Thirty-five patients admitted with ST-elevation myocardial infarction that had three-vessel intravascular ultrasound (IVUS) immediately after revascularization and at 13 months follow-up were included. Three dimensional (3D) reconstruction of the non-culprit vessels were performed using (i) quantitative coronary angiography (QCA) and (ii) methodology involving fusion of IVUS and biplane angiography. In both models, blood flow simulation was performed and the minimum predominant ESS was estimated in 3 mm segments. Baseline plaque characteristics and ESS were used to identify predictors of atherosclerotic disease progression defied as plaque area increase and lumen reduction at follow-up. Fifty-four vessels were included in the final analysis. A moderate correlation was noted between ESS estimated in the 3D QCA and the IVUS-derived models (r = 0.588, P < 0.001); 3D QCA accurately identified segments exposed to low (<1 Pa) ESS in the IVUS-based reconstructions (AUC: 0.793, P < 0.001). Low 3D QCA-derived ESS (<1.75 Pa) was associated with an increase in plaque area, burden, and necrotic core at follow-up. In multivariate analysis, low ESS estimated either in 3D QCA [odds ratio (OR): 2.07, 95% confidence interval (CI): 1.17-3.67; P = 0.012) or in IVUS (<1 Pa; OR: 2.23, 95% CI: 1.23-4.03; P = 0.008) models, and plaque burden were independent predictors of atherosclerotic disease progression; 3D QCA and IVUS-derived models had a similar accuracy in predicting disease progression (AUC: 0.826 vs. 0.827, P = 0.907).

CONCLUSIONS

3D QCA-derived ESS can predict disease progression. Further research is required to examine its value in detecting vulnerable plaques.

Early strut protrusion and late neointima thickness in the Absorb bioresorbable scaffold: a serial wall shear stress analysis up to five years

AIMS

The aim of the study was to evaluate the effect of strut protrusion (SP) on wall shear stress (WSS) and neointimal growth (NG) one and five years after implantation of an Absorb bioresorbable vascular scaffold.

METHODS AND RESULTS

Eight patients were selected from a first-in-man study. Following three-dimensional (3D) reconstruction of coronaries, WSS was quantified using Newtonian steady-flow simulation in each cross-section at 5° subunits (sectors) of the circumferential luminal surface. At one year, neointimal thickness (NT) was measured by optical coherence tomography (OCT) and correlated to WSS and SP post procedure. Median SP was 112.9 (90.8, 133.1) µm post implantation. Post procedure, a logarithmic inverse relationship between SP and post-implantation WSS (r=-0.425, p<0.001; correlation coefficients in a range from -0.143 to -0.553) was observed, whereas a correlation between baseline logarithm-transformed WSS (log-WSS) and NT (r=-0.451, p<0.001; correlation coefficients ranged from -0.140 to -0.662) was documented at one year. Mixed-effects analysis between baseline log-WSS and NT at follow-up yielded a slope of 30 µm/ln Pascal (Pa) and a y-intercept of 98 µm. As a result of NG, median flow area decreased from 6.91 (6.53, 7.48) mm2 post implantation to 5.65 (5.47, 6.02) mm2 at one-year follow-up (p=0.01) and to 5.75±1.37 mm2 at five-year follow-up (p=0.024). However, the vessel surface exposed to low WSS (<1 Pa) decreased significantly post procedure (42%) to one year (35.9%) and five years (15.2%) (p-overall <0.0001).

CONCLUSIONS

SP disturbs laminar flow, creates regions of low WSS (<1.0 Pa) that are associated with NG and lumen area reduction. Low WSS post implantation reduced significantly at long-term follow-up. Thin struts with effective embedment would substantially reduce NG and accelerate homogenisation of WSS towards physiological values.

Coronary Shear Stress after Implantation of Bioresorbable Scaffolds – a Modern Interdisciplinary Concept at the Border between Interventional Cardiology and Cardiac Imaging

Bioresorbable scaffolds/stents offer new and exciting perspectives in the treatment of patients with acute coronary syndromes, especially after the recent development of invasive imaging techniques, such as optical coherence tomography, which allow complete assessment of vascu-lar segments. A particular advantage of bioresorbable scaffolds is that once the biosorption of the scaffold is complete, the vascular segment regains its normal physiological functions, thus eliminating the risk of late complications. New studies show the importance of shear stress in the progression of vascular atherosclerosis or in accelerating endothelial turnover. Based on the current knowledge in this field, a future standardized determination of shear stress may help in the long-term follow-up of patients that have suffered or are at risk of developing an acute coronary syndrome.

Optical coherence tomography evaluation of the absorb bioresorbable scaffold performance for overlap versus non-overlap segments in patients with coronary chronic total occlusion: insight from the GHOST-CTO registry

The Absorb bioresorbable vascular scaffold (BVS) promised to avoid some of the disadvantages of its metal predecessors. Even though it has been taken off the market, limited data is available about its use in coronary chronic total occlusion (CTO) and its performance in overlap segments, which would be of special research interest due to its large thickness. This data is still pertinent since the platform of bioresorbable devices has not been abandoned, with several companies working on it. We aimed to compare healing and performance between overlap (OL) and non-overlap regions (NOL) of CTO lesions treated with BVS, using optical coherence tomography (OCT). Fourteen patients with overlapping BVS were included from the GHOST-CTO registry, resulting in 25 OL and 38 NOL regions. OCT based parameters were compared between OL and NOL groups at baseline (post-implantation) and 12-month follow-up. The mean age was 61.7 ± 7.2 years and 12 (86%) were males. Twelve (86%) patients underwent PCI for stable coronary artery disease and 2 (14%) had unstable angina. At 12-month follow-up, mean lumen area decreased in both NOL and OL regions, but the decrease was significantly larger in the OL region (NOL - 0.7 ± 1.33 vs. OL - 2.4 ± 1.54 mm²; p = 0.002). Mean scaffold area increased in both regions, but increased significantly more in NOL ( + 1.1 ± 1.54 vs. + 0.4 ± 1.16 mm²; p = 0.016). The percent of uncovered struts was lower in the OL group (5.0 ± 6.6% vs. 3.75 ± 8.7%, p = 0.043), whereas the percentage of malapposed struts was similar (0.3 ± 0.5% vs. 0.7 ± 2.3%, p = 0.441). Neointimal hyperplasia (NIH) was more pronounced in the OL region (0.13 ± 0.04 vs. 0.24 ± 0.10 mm², p = 0.001). The OL and NOL segments showed comparable healing in terms of coverage and malapposition. However, NIH was more prominent in OL region. The long-term clinical implications of these findings needs further evaluation. The present study provides important insights for future development of BVS technology.

A Multi-Modality Image-Based FSI Modeling Approach for Prediction of Coronary Plaque Progression Using IVUS and OCT Data with Follow-Up

Medical image resolution has been a serious limitation in plaque progression research. A modeling approach combining intravascular ultrasound (IVUS) and optical coherence tomography (OCT) was introduced and patient follow-up IVUS and OCT data were acquired to construct 3D coronary models for plaque progression investigations. Baseline and follow-up in vivo IVUS and OCT coronary plaque data were acquired from one patient with 105 matched slices selected for model construction. 3D FSI models based on IVUS and OCT data (denoted as IVUS+OCT model) were constructed to obtain stress/strain and wall shear stress (WSS) for plaque progression prediction. IVUS-based IVUS50 and IVUS200 models were constructed for comparison with cap thickness set as 50 and 200 microns, respectively. Lumen area increase (LAI), plaque area increase (PAI) and plaque burden increase (PBI) were chosen to measure plaque progression. The least squares support vector machine method was employed for plaque progression prediction using 19 risk factors. For IVUS+OCT model with LAI, PAI and PBI, the best single predictor was plaque strain, local plaque stress, and minimal cap thickness, with prediction accuracy as 0.766, 0.838 and 0.890, respectively; The prediction accuracy using best combinations of 19 factors was 0.911, 0.881 and 0.905, respectively. Compared to IVUS+OCT model, IVUS50 and IVUS200 models had errors ranging from 1% to 66.5% in quantifying cap thickness, stress, strain and prediction accuracies. WSS showed relatively lower prediction accuracy compared to other predictors in all 9 prediction studies.

Long-term safety of bioresorbable scaffolds: insights from a network meta-analysis including 91 trials

AIMS

The aim of this study was to investigate the long-term safety and efficacy of biodegradable scaffolds and metallic stents.

METHODS AND RESULTS

We analysed a total of 91 randomised controlled trials with a mean follow-up of 3.7 years in 105,842 patients which compared two or more coronary metallic stents or biodegradable scaffolds and reported the long-term clinical outcomes (≥2 years). Network meta-analysis showed that patients treated with the Absorb bioresorbable vascular scaffold (BVS) had a significantly higher risk of definite or probable scaffold thrombosis (ScT) compared to those treated with metallic DES. The risk of very late ScT was highest with the Absorb BVS among comparators. Pairwise conventional meta-analysis demonstrated that the elevated risk of ScT with Absorb BVS compared to cobalt-chromium everolimus-eluting stents was consistent across the time points of ≤30 days (early), 31 days - 1 year (late) and >1 year (very late) ScT. In addition, target lesion failure rates were significantly higher in the Absorb BVS cohort, driven by both increased risk of target vessel myocardial infarction and ischaemia-driven target lesion revascularisation.

CONCLUSIONS

Absorb BVS implantation was associated with increased risk of long-term and very late ScT compared to current-generation metallic DES. The risk of ScT occurred with a rising trend beyond one year.

Mechanical performance and healing patterns of the novel sirolimus-eluting bioresorbable Fantom scaffold: 6-month and 9-month follow-up by optical coherence tomography in the FANTOM II study

Objectives

We aimed to evaluate the mechanical properties and healing patterns 6 and 9 months after implantation of the sirolimus-eluting Fantom bioresorbable scaffold (BRS).

Background

The Fantom BRS (Reva Medical, San Diego, USA) has differentiating properties including radiopacity, strut thickness of 125 µm, high expansion capacity and has demonstrated favourable mid-term clinical and angiographic outcomes.

Methods and results

FANTOM II was a prospective, single arm study with implantation of the Fantom BRS in 240 patients with stable angina pectoris. Guidance by optical coherence tomography (OCT) was encouraged and was repeated at 6-month (cohort A) or 9-month follow-up (cohort B). Matched baseline and follow-up OCT recordings were available in 152 patients. In-scaffold mean lumen area in cohort A was 6.8±1.7 mm² and 5.7±1.4 mm² at baseline and follow-up (p<0.0001) and was 7.2±1.6 mm² and 5.6±1.4 mm² in cohort B (p<0.0001). Mean scaffold area remained stable from 7.1±1.5 mm² at baseline to 7.2±1.4 mm² at 6 months (p=0.12), and from 7.4±1.5 mm² to 7.3±1.4 mm² at 9 months. Strut malapposition was median 0.8 (IQR 0.0;3.5)% and 1.8 (IQR 0.3;6.0)% at baseline and was 0.0 (IQR 0.0;0.0)% in both groups at 6-month and 9-month follow-up. Strut tissue coverage was 98.1 (IQR 95.9;99.4)% at 6 months and 98.9 (IQR 98.3;100.0)% at 9 months.

Conclusions

The novel Fantom BRS had favourable healing patterns at 6-month and 9-month follow-up as malapposition was effectively resolved and strut coverage was almost complete. The scaffold remained stable through follow-up with no signs of systematic late recoil.

ZBTB46 is a shear-sensitive transcription factor inhibiting endothelial cell proliferation via gene expression regulation of cell cycle proteins

ZBTB46 is a transcription factor identified in classical dendritic cells and keeps dendritic cells in a quiescent state. Chromatin immunoprecipitation sequencing in dendritic cells has identified over 1300 potential gene targets of ZBTB46, affecting many processes including cell cycle. Endothelial cells (ECs) also express ZBTB46 and are mostly in a quiescent non-proliferative state. While EC proliferation is a critical process in development, dysregulation of EC proliferation as seen in areas of disturbed flow play an important role in many disease processes such as atherosclerosis, pulmonary hypertension, transplant vasculopathy, neointimal hyperplasia, and in-stent restenosis. We studied the role of ZBTB46 in ECs, hypothesizing that it inhibits EC proliferation. Using a model of disturbed flow in mice, we found that ZBTB46 is expressed in murine arterial ECs in vivo, and is downregulated by disturbed flow. In vitro results using HAECs showed that cell confluence and laminar shear stress, both known physiological conditions promoting EC quiescence, led to upregulation of ZBTB46 expression. Adenoviral-mediated overexpression of ZBTB46 in vitro caused reduced EC proliferation, and increased number of cells in the G₀/G₁ phase of cell cycle, without affecting apoptosis or senescence, while siRNA knockdown of ZBTB46 negated the known inhibitory role of unidirectional laminar shear stress on EC proliferation. ZBTB46 overexpression also led to a broad suppression of genes involved in cell cycle progression including multiple cyclins and cyclin-dependent kinases, but an increase in the CDK inhibitor CDKN1A. Phosphorylation of the retinoblastoma protein was also decreased as assessed by Western blot. Tube formation on Matrigel was reduced, suggesting an inhibitory role for ZBTB46 in angiogenesis. Further research is required to investigate the potential role of ZBTB46 in specific pathologic conditions and whether it can be targeted in a therapeutic manner.

Post-implantation shear stress assessment: an emerging tool for differentiation of bioresorbable scaffolds

Optical coherence tomography based computational flow dynamic (CFD) modeling provides detailed information about the local flow behavior in stented/scaffolded vessel segments. Our aim is to investigate the in-vivo effect of strut thickness and strut protrusion on endothelial wall shear stress (ESS) distribution in ArterioSorb Absorbable Drug-Eluting Scaffold (ArterioSorb) and Absorb everolimus-eluting Bioresorbable Vascular Scaffold (Absorb) devices that struts with similar morphology (quadratic structure) but different thickness. In three animals, six coronary arteries were treated with ArterioSorb. At different six animals, six coronary arteries were treated with Absorb. Following three-dimensional(3D) reconstruction of the coronary arteries, Newtonian steady flow simulation was performed and the ESS were estimated. Mixed effects models were used to compare ESS distribution in the two devices. There were 4591 struts in the analyzed 477 cross-sections in Absorb (strut thickness = 157 µm) and 3105 struts in 429 cross-sections in ArterioSorb (strut thickness = 95 µm) for the protrusion analysis. In cross-section level analysis, there was significant difference between the scaffolds in the protrusion distances. The protrusion was higher in Absorb (97% of the strut thickness) than in ArterioSorb (88% of the strut thickness). ESS was significantly higher in ArterioSorb (1.52 ± 0.34 Pa) than in Absorb (0.73 ± 2.19 Pa) (p = 0.001). Low- and very-low ESS data were seen more often in Absorb than in ArterioSorb. ArterioSorb is associated with a more favorable ESS distribution compared to the Absorb. These differences should be attributed to different strut thickness/strut protrusion that has significant effect on shear stress distribution.

A Patient-Specific Study Investigating the Relation between Coronary Hemodynamics and Neo-Intimal Thickening after Bifurcation Stenting with a Polymeric Bioresorbable Scaffold

We present an application of a validated reconstruction methodology for the comparison between patient-specific hemodynamics and neo-intimal thickening at nine months from the intervention. (1) Background: Coronary bifurcation stenting alters the vessel geometry, influencing the local hemodynamics. The evaluation of wall shear stress (WSS) relies on the application of computational fluid dynamics to model its distribution along the coronary tree. The endothelium actively responds to WSS, which triggers eventual cell proliferation to cover the stent struts. (2) Methods: Baseline optical coherence tomography and angiographic data were combined to reconstruct a patient-specific coronary bifurcation with an implanted bioresorbable scaffold and to simulate the hemodynamics. Results were linked with the neo-intimal thickening after nine months from the intervention. (3) Results: Blood velocity patterns were disrupted at the bifurcation due to the presence of the stent. It was observed that 55.6% of the scaffolded lumen surface was exposed to values of time-averaged WSS lower than 0.4 Pa. Follow-up images showed a luminal narrowing of 19% in the main branch. There was also a complete coverage in 99% of struts. (4) Conclusions: This approach provided valuable complementary information that might improve the clinical outcomes in this subset of coronary diseases.

Biomaterials and heart recovery: cardiac repair, regeneration and healing in the MCS era: a state of the "heart"

Regenerative medicine is an emerging interdisciplinary field of scientific research that, supported by tissue engineering is, nowadays, a valuable and reliable solution dealing with the actual organs shortage and the unresolved limits of biological or prosthetic materials used in repair and replacement of diseased or damaged human tissues and organs. Due to the improvements in design and materials, and to the changing of clinical features of patients treated for valvular heart disease the distance between the ideal valve and the available prostheses has been shortened. We will then deal with the developing of new tools aiming at replacing or repair cardiac tissues that still represent an unmet clinical need for the surgeons and indeed for their patients. In the effort of improving treatment for the cardiovascular disease (CVD), scientists struggle with the lack of self-regenerative capacities of finally differentiated cardiovascular tissues. In this context, using several converging technological approaches, regenerative medicine moves beyond traditional transplantation and replacement therapies and can restore tissue impaired function. It may also play an essential role in surgery daily routine, leading to produce devices such as injectable hydrogels, cardiac patches, bioresorbable stents and vascular grafts made by increasingly sophisticated biomaterial scaffolds; tailored devices promptly fabricated according to surgeon necessity and patient anatomy and pathology will hopefully represent a daily activity in the next future. The employment of these devices, still far from the in vitro reproduction of functional organs, has the main aim to achieve a self-renewal process in damaged tissues simulating endogenous resident cell populations. In this field, the collaboration and cooperation between cardiothoracic surgeons and bioengineers appear necessary to modify these innovative devices employed in preclinical studies according to the surgeon's needs.

Implications of the local hemodynamic forces on the formation and destabilization of neoatherosclerotic lesions

OBJECTIVE

To examine the implications of endothelial shear stress (ESS) distribution in the formation of neoatherosclerotic lesions.

METHODS

Thirty six patients with neoatherosclerotic lesions on optical coherence tomography (OCT) were included in this study. The OCT data were used to reconstruct coronary anatomy. Blood flow simulation was performed in the models reconstructed from the stent borders which it was assumed that represented the lumen surface at baseline, immediate after stent implantation, and the estimated ESS was associated with the neointima burden, neoatherosclerotic burden and neointima characteristics. In segments with neointima rupture blood flow simulation was also performed in the model representing the lumen surface before rupture and the ESS was estimated at the ruptured site.

RESULTS

An inverse association was noted between baseline ESS and the incidence and the burden of neoatherosclerotic (β = -0.60, P < 0.001, and β = -4.05, P < 0.001, respectively) and lipid-rich neoatherosclerotic tissue (β = -0.54, P < 0.001, and β = -3.60, P < 0.001, respectively). Segments exposed to low ESS (<1 Pa) were more likely to exhibit macrophages accumulation (28.2% vs 10.9%, P < 0.001), thrombus (11.0% vs 2.6%, P < 0.001) and evidence of neointima discontinuities (8.1% vs 0.9%, P < 0.001) compared to those exposed to normal or high ESS. In segments with neointima rupture the ESS was high at the rupture site compared to the average ESS over the culprit lesion (4.00 ± 3.65 Pa vs 3.14 ± 2.90 Pa, P < 0.001).

CONCLUSIONS

Local EES is associated with neoatherosclerotic lesion characteristics, which suggests involvement of ESS in the formation of vulnerable plaques in stented segments.

Local Flow Patterns After Implantation of Bioresorbable Vascular Scaffold in Coronary Bifurcations - Novel Findings by Computational Fluid Dynamics

BACKGROUND

Development of methods for accurate reconstruction of bioresorbable scaffolds (BRS) and assessing local hemodynamics is crucial for investigation of vascular healing after BRS implantation.

METHODS AND RESULTS

Patients with BRS that crossed over in a coronary bifurcation were included for analysis. Reconstructions of the coronary lumen and BRS were performed by fusion of optical coherence tomography and coronary angiography generating a tree model (TM) and a hybrid model with BRS (TM-BRS). A virtual BRS model with thinner struts was created and all 3 models were analyzed using computational fluid dynamics to derive: (1) time-average shear stress (TASS), (2) TASS gradient (TASSG), which represents SS heterogeneity, and (3) fractional flow reserve (FFR). Reconstruction of the BRS was successful in all 10 patients. TASS and TASSG were both higher by TM-BRS than by TM in main vessels (difference 0.27±4.30 Pa and 10.18±27.28 Pa/mm, P<0.001), with a remarkable difference at side branch ostia (difference 13.51±17.40 Pa and 81.65±105.19 Pa/mm, P<0.001). With thinner struts, TASS was lower on the strut surface but higher at the inter-strut zones, whereas TASSG was lower in both regions (P<0.001 for all). Computational FFR was lower by TM-BRS than by TM for both main vessels and side branches (P<0.001).

CONCLUSIONS

Neglecting BRS reconstruction leads to significantly lower SS and SS heterogeneity, which is most pronounced at side branch ostia. Thinner struts can marginally reduce SS heterogeneity.

Serial 5-Year Evaluation of Side Branches Jailed by Bioresorbable Vascular Scaffolds Using 3-Dimensional Optical Coherence Tomography: Insights From the ABSORB Cohort B Trial (A Clinical Evaluation of the Bioabsorbable Everolimus Eluting Coronary Stent System in the Treatment of Patients With De Novo Native Coronary Artery Lesions)

BACKGROUND

The long-term fate of Absorb bioresorbable vascular scaffold (Abbott Vascular, Santa Clara, CA) struts jailing side branch ostia has not been clarified. We therefore evaluate serially (post-procedure and at 6 months, 1, 2, 3, and 5 years) the appearance and fate of jailed Absorb bioresorbable vascular scaffold struts.

METHODS AND RESULTS

We performed 3-dimensional optical coherence tomographic analysis of the ABSORB Cohort B trial (A Clinical Evaluation of the Bioabsorbable Everolimus Eluting Coronary Stent System in the Treatment of Patients With De Novo Native Coronary Artery Lesions) up to 5 years using a novel, validated cut-plane analysis method. We included 29 patients with a total of 85 side branch ostia. From the 12 ostia which could be assessed in true serial fashion, 7 showed a pattern of initial decrease in the ostial area free from struts, followed by an increase in strut-free ostial area toward the end of the 5 years of follow-up. In a repeated-measures analysis with time as fixed variable and ostial area free from struts as dependent variable, we showed a numeric decrease in the estimated ostial area free from struts from 0.75 mm² (baseline) to 0.68 mm² (first follow-up visit at 6 months or 1 year) and 0.63 mm² (second follow-up visit at 2 or 3 years). However, from the second visit to the 5-year follow-up visit, there was a statistically significant increase from 0.63 to 0.89 mm² (P=0.001). Struts overlying an ostium divided the ostium into compartments, and the number of these compartments decreased over time.

CONCLUSIONS

This study showed that in most cases, the side branch ostial area free from struts initially decreased. However, with full scaffold bioresorption, the ostial area free from scaffold increased between 2 to 3 years and 5 years in the vast majority of patients.

CLINICAL TRIAL REGISTRATION

URL: http://www.clinicaltrials.gov. Unique identifier: NCT00856856.

Hemodynamic analysis of a novel bioresorbable scaffold in porcine coronary artery model

BACKGROUND

The shear stress distribution assessment can provide useful insights for the hemodynamic performance of the implanted stent/scaffold. Our aim was to investigate the effect of a novel bioresorbable scaffold, Mirage on local hemodynamics in animal models.

METHOD

The main epicardial coronary arteries of 7 healthy mini-pigs were implanted with 11 Mirage Microfiber sirolimus-eluting Bioresorbable Scaffolds (MMSES). Optical coherence tomography (OCT) was performed post scaffold implantation and the obtained images were fused with angiographic data to reconstruct the coronary artery anatomy. Blood flow simulation was performed and Endothelial Shear Stress(ESS) distribution was estimated for each of the 11 scaffolds. ESS data were extracted in each circumferential 5-degree subunit of each cross-section in the scaffolded segment. The generalized linear mixed-effect analysis was implemented for the comparison of ESS in two scaffold groups; 150-µm strut thickness MMSES and 125-µm strut thickness MMSES.

RESULTS

ESS was significantly higher in MMSES (150 µm) [0.85(0.49-1.40) Pa], compared to MMSES (125 µm) [0.68(0.35-1.18) Pa]. Both MMSES (150 µm) and MMSES (125 µm) revealed low recirculation zone percentages per luminal surface area [3.17% ± 1.97% in MMSES (150 µm), 2.71% ± 1.32% in MMSES (125 µm)].

CONCLUSION

Thinner strut Mirage scaffolds induced lower shear stress due to the small size vessels treated as compared to the thick strut version of the Mirage which was implanted in relatively bigger size vessels. Vessel size should be taken into account in planning BRS implantation. Small vessels may not get benefit from BRS implantation even with a streamlined strut profile. This pilot study warrants comparative assessment with commercially available bioresorbable scaffolds.

Patient-Specific Modeling of Stented Coronary Arteries Reconstructed from Optical Coherence Tomography: Towards a Widespread Clinical Use of Fluid Dynamics Analyses

The recent widespread application of optical coherence tomography (OCT) in interventional cardiology has improved patient-specific modeling of stented coronary arteries for the investigation of local hemodynamics. In this review, the workflow for the creation of fluid dynamics models of stented coronary arteries from OCT images is presented. The algorithms for lumen contours and stent strut detection from OCT as well as the reconstruction methods of stented geometries are discussed. Furthermore, the state of the art of studies that investigate the hemodynamics of OCT-based stented coronary artery geometries is reported. Although those studies analyzed few patient-specific cases, the application of the current reconstruction methods of stented geometries to large populations is possible. However, the improvement of these methods and the reduction of the time needed for the entire modeling process are crucial for a widespread clinical use of the OCT-based models and future in silico clinical trials.