On the adsorption of cetyldimethylbenzylammonium chloride at the mercury/electrolyte solution interface

Adsorption of cationic surfactants on covered hanging mercury drop electrode surface of variable area

Cetyldimethylbenzylammonium chloride (CDBACl) or cetyltrimethylammonium bromide (CTAB) is preadsorbed on mercury and used as substrate. The adsorptive stripping voltammetry with the two-step procedure is used. The mercury droplet with the preadsorbed surfactant is expanded in aqueous solutions of KCl, KBr, CTAB, CDBACl, or cetylethyldimethylammonium bromide (CEDAB). The surface area was increased from 0.0022cm(2) up to 0.0571cm(2). The surfactant molecules are maintained close to each other and in the vicinity of the electrode by the applied electric field. The expanding of the droplets resulted in a reorientation of the adsorbed molecules depending on the surfactant surface concentration. In some cases, condensed films were observed. Differences were noticed in the adsorption and desorption potential region. A linear increase in the capacitance current with the surface area was found in all cases up to a maximum increase in the surface area. Partly disorganized films were also observed. In some cases, defects were noticed during expansion. In one case, fractal structure was observed.

Adsorption of cetyltrimethylammonium bromide and/or cetyldimethylbenzylammonium chloride on partly covered hanging mercury drop electrode

Adsorbed cetyldimethylbenzylammonium chloride (CDBACl) or cetyltrimethylammonium bromide (CTAB) on mercury is used as template for the adsorption of CTAB, CDBACl, or their equimolar mixture at 20 °C. Adsorptive stripping voltammetry with the two step procedure is used. The results are compared with previously published results on the adsorption of CTAB and CDBACl on mercury and then transferred in base electrolyte. A surfactant is preadsorbed. The adsorption of the second does not remove away from the mercury the first one, as evidenced by the capacitance measurements and the repeated scans. The surfactants were maintained close to each other and in the vicinity of the electrode by the applied electric field. In all cases studied, there was a decrease in the capacitance in the potential range -0.8 to -1 V to very low capacitance values forming condensed film. Mixed films and synergy effects were observed. The already adsorbed CTAB on mercury did not permit the desorption-reorientation peaks of CDBACl. Shifts of the capacitance peaks were observed to more positive potentials and were attributed to the occurrence of a slow change in the organization of the monolayer. The electrical state of the preadsorbed surfactant would be of critical importance in the formation of the various structures. The results suggested that the ordering and arrangement of molecules could be controlled by appropriate selection of templates.

Condensed film formation of binary mixtures of cetyltrimethylammonium bromide and cetyldimethylbenzylammonium chloride in a wide potential region at the mercury/electrolyte interface

The adsorption of binary mixtures of cetyltrimethylammonium bromide (CTAB) and cetyldimethylbenzylammonium chloride (CDBACl) at the mercury/electrolyte interface was studied in various electrolyte systems. The optimum surfactant concentration and electrolyte ratio was searched for, to obtain the formation of a condensed film at as wide a potential range as possible at the highest temperature possible. The optimum conditions found were 2 x 10(-4) M CTAB and 2 x 10(-4) M CDBACl in 0.07 M KF and 0.03 M KBr at 2 degrees C. The capacitances vs time curves were used for the reconstruction of isochronous capacitance vs potential curves. These curves showed that in that system the condensed film was formed in the potential range from -0.4 to -1.9 V vs Ag/AgCl in less than 220 s. The stability of this film, following the removal of the mercury drop from the solution, was also studied.

Effect of the deaeration on the adsorption of some cationic surfactants at the mercury/electrolyte solution interface

The effect of the deaeration on the adsorption of three cationic surfactants cetyldimethylbenzylammonium chloride (CDBACl), cetyltrimethylammonium bromide (CTAB) and octadecyltrimethylammonium bromide (OTAB) at the mercury/electrolyte solution interface is studied. The deaeration is studied using either nitrogen or helium and the effect of deaeration process and time is also studied. In all cases an effect of the deaeration time is found which is mainly observed at potentials where a condensed film is formed. Capacity-time curves at the potentials where the film is formed show a nucleation and growth mechanism with induction time that depends on the deaeration time. The deaeration slows down the kinetics of the film formation but does not change the equilibrium capacitance value of the film. The decrease of the dissolved gas from the water that perturbs its structure is perhaps the main reason for the behaviour observed during the adsorption of these surfactants.