Temperature-induced intermicellization and contraction in aqueous mixtures of sodium dodecyl sulfate and an amphiphilic diblock copolymer

Effect of PCL end-groups on the self-assembly process of Pluronic in aqueous media

Understanding self-assembly of amphiphilic copolymers in aqueous solution is an important issue in many areas, e.g., in order to tailor-make carriers for drugs and genes. We have synthesized modified versions of the copolymer of type PEO-PPO-PEO (Pluronic, F127), with short (PCL(5)) or long (PCL(11)) PCL blocks at both ends. Turbidity, dynamic light scattering (DLS), small angle neutron scattering (SANS), and rheology measurements were carried out on dilute aqueous solutions of these polymers to investigate their self-assembly behavior. The DLS results clearly show that both micellization and inter-micellization can be controlled by polymer concentration, temperature, and length of the PCL block. The interplay between unimers, micelles, and clusters of micelles could be monitored and the size and size distribution of the species were determined. The SANS data could be portrayed by a spherical core-shell model at all considered conditions of temperature and concentration for F127 and PCL(5) apart from F127 at the lowest temperature measured. The SANS data for PCL(11) were described by a spherical core-shell model at low temperatures, whereas at elevated temperatures asymmetric sub-structures appeared and a cylindrical core-shell model was employed in the analysis of the data. The appearance of pronounced correlation peaks at elevated temperatures signalizes marked intermicellar interactions. The shear viscosity data revealed a minor shear thinning effect, suggesting that the interchain structures are rather stable and not easily disrupted. The work shows that PCL-modification of Pluronic has a large influence on the self-assembly process and on the final structure of the assemblies.

Oxygen-controlled phase segregation in poly(N-isopropylacrylamide)/laponite nanocomposite hydrogels

The combination of nanoparticles and polymers into nanocomposite gels has been shown to be a promising route to creating soft materials with new or improved properties. In the present work, we have made use of Laponite nanoparticles in combination with a poly(N-isopropylacrylamide) (PNIPAAM) polymer and describe a phenomenon taking place during the polymerization and gelling of this system. The presence of small amounts of oxygen in the process induces two distinctly separated phases, one polymer-rich and one polymer-deficient water-clay phase. Complex interactions among clay, oxygen, and the polymer are found to govern the behavior of these phases. It is also observed that the initial clay concentration can be used to control the volume fraction of the polymer-deficient phase directly. The dynamics of the phase boundary is found to be dependent on water penetration and in general to exhibit non-Fickian behavior. An approach using video recording to monitor hydrogel swelling is also presented, and its advantages are addressed.

Temperature-induced adsorption and optical properties of an amphiphilic diblock copolymer adsorbed onto flat and curved silver surfaces

Temperature-induced adsorption of a thermoresponsive amphiphilic copolymer, containing poly(N-isopropylacrylamide), on citrate-capped silver nanoparticles and planar silver surfaces has been studied with the aid of quartz crystal microbalance with dissipation monitoring (QCM-D) and dynamic light scattering (DLS). The results clearly show that both the amount of adsorbed copolymer and thickness of the adsorbed layer increase strongly at temperatures above the lower critical solution temperature (LCST). These findings are ascribed to enhanced hydrophobicity of the polymer and higher affinity for polymer adsorption at elevated temperatures and formation of intermicellar structures of the copolymer. The values of the layer thickness calculated from QCM-D data are practically identical to the values for the hydrodynamic thickness from DLS. This result suggests that the adsorbed layer is compact with few tails protruding out into the bulk. The surface plasmon peak for silver is observed at all temperatures, and the maximum is red-shifted with increasing temperature, which is attributed to an increase of the localized refractive index as more polymer chains are adsorbed onto the silver particles.