Stable colloidal dispersion of functionalized reduced graphene oxide in aqueous medium for transparent conductive film

Synergetic Effect of Polyaniline and Graphene in Their Composite Supercapacitor Electrodes: Impact of Components and Parameters of Chemical Oxidative Polymerization

The current development of clean and high efficiency energy sources such as solar or wind energy sources has to be supported by the design and fabrication of energy storage systems. Electrochemical capacitors (or supercapacitors (SCs)) are promising devices for energy storage thanks to their highly efficient power management and possible small size. However, in comparison to commercial batteries, SCs do not have very high energy densities that significantly limit their applications. The value of energy density directly depends on the capacitance of full SCs and their cell voltage. Thus, an increase of SCs electrode specific capacitance together with the use of the wide potential window electrolyte can result in high performance SCs. Conductive polymer polyaniline (PANI) as well as carbonaceous materials graphene (G) or reduced graphene oxide (RGO) have been widely studied for usage in electrodes of SCs. Although pristine PANI electrodes have shown low cycling stability and graphene sheets can have low specific capacitance due to agglomeration during their preparation without a spacer, their synergetic effect can lead to high electrochemical properties of G/PANI composites. This review points out the best results for G/PANI composite in comparison to that of pristine PANI or graphene (or RGO). Various factors, such as the ratio between graphene and PANI, oxidants, time, and the temperature of chemical oxidative polymerization, which have been determined to influence the morphology, capacitance, cycling stability, etc. of the composite electrode materials measured in three-electrode system are discussed. Consequently, we provide an in-depth summary on diverse promising approaches of significant breakthroughs in recent years and provide strategies to choose suitable electrodes based on PANI and graphene.

Functionalized graphene oxide nanosheets with folic acid and silk fibroin as a novel nanobiocomposite for biomedical applications

In this paper, a novel graphene oxide-folic acid/silk fibroin (GO-FA/SF) nanobiocomposite scaffold was designed and fabricated using affordable and non-toxic materials. The GO was synthesized using the hummer method, covalently functionalized with FA, and then easily conjugated with extracted SF via the freeze-drying process. For characterization of the scaffold, several techniques were employed: Fourier-transform infrared (FT-IR), field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray (EDX), and thermogravimetric analysis (TGA). The cell viability method, hemolysis, and anti-biofilm assays were performed, exploring the biological capability of the nanobiocomposite. The cell viability percentages were 96.67, 96.35 and 97.23% for 24, 48, and 72 h, respectively, and its hemolytic effect was less than 10%. In addition, it was shown that this nanobiocomposite prevents the formation of Pseudomonas aeruginosa biofilm and has antibacterial activity.

Reduced Graphene Oxide—Polycarbonate Electrodes on Different Supports for Symmetric Supercapacitors

Electrode materials for electrochemical capacitors or supercapacitors (SCs) are widely studied, as they are needed for the development of energy storage devices in electrical vehicles and flexible electronics. In the current work, a self-supported paper of reduced graphene oxide (rGO) with polycarbonate (PC) (as rGO-PC composite) was prepared by simple vacuum filtration and low-temperature annealing. rGO-PC as a freestanding single electrode was studied in a three-electrode system and presented a capacitive energy storage mechanism. To fabricate SCs based on rGO-PC, flexible polyethylene terephthalate (PET) with layers of both Cu tape (Cu tape) and carbon tape (C tape) (PET/Cu/C), as well as PET covered by graphene ink (PET/GrI), were used as supports. Fabricated flexible symmetric SCs have shown similar behavior with a higher areal capacitance value than that on PET/Cu/C substrate.

Effects of Modification Degrees on the Colloidal Stability of Amphiphilic Janus Graphene Oxide in Aqueous Solution with and without Electrolytes

Colloidal stability of modified graphene oxide (GO) is fundamental for its practical applications. Meanwhile, most of the investigations mainly focused on the nanosheets modified by a certain amount of modifiers and neglected the effects of the modification degree, which could vary the physical and chemical properties of modified GO and significantly affect its stability in solution. To the best of our knowledge, this study initially investigated the impact of modification degrees on the colloidal stability of graphene-based amphiphilic Janus nanosheets (JGO) via both experimental and theoretical approaches. The prepared JGO, asymmetrically grafted by dodecylamine, exhibited a direct relation between the modification degree and nanosheet thickness, refractive index, electrostatic properties, hydrophobicity, and the ultimate colloidal stability. In addition, the ionic strength imposed distinctive influences on the aggregation behavior of JGO. Based on the comparison between experimental results and theoretical calculation, it was revealed that the JGO should be modeled as two-dimensional (2D) nanosheets in pure water and be treated as 3D spherical particles in electrolyte solutions for the prediction with the extended Derjaguin-Landau-Verwey-Overbeek theory.

On the effect of particle surface chemistry in film stratification and morphology regulation

Combinations of colloids and binders are often used to formulate functional coatings. In these mixtures, competition between particle migration, polymer chain diffusion, evaporation and sedimentation affects their respective spatial location and therefore can govern the surface features. In addition to this, the surface chemistry of the nanoparticles (NPs) and the resulting interparticle interactions can play a significant role in dictating the morphology and the properties of resultant films. Hence it would be possible to tune the surface and bulk topology of the films by controlling these parameters. A combination of various acrylic binders with two types of silica sols, bare (BSiO2) and modified silica (MSiO2), differing in their ability to gel, were formulated and dried under controlled conditions. Factors influencing the mobility and migration of binder and silica particles were evaluated with respect to particle concentration and drying rate. MSiO2 films showed prominent pores with gradual increase in Si% across the cross-section of the films, whereas, BSiO2 films had no pores and showed a uniform Si content across the cross-section of the films. This difference is explained by the variation in gelation between BSiO2 compared to MSiO2, that hindered the NPs migration and affects the infiltration and stratification process. This study paves a path forward to achieve desired surface and bulk porosity from colloidal silica coatings by effective control of chemistry of particles along with process parameters.

Dispersed graphene materials of biomedical interest and their toxicological consequences

Graphene is one-atom thick nanocarbon displaying a unique honeycomb structure and extensive conjugation. In addition to high surface area to mass ratio, it displays unique optical, thermal, electronic and mechanical properties. Atomic scale tunability of graphene has attracted immense research interest with a prospective utility in electronics, desalination, energy sectors, and beyond. Its intrinsic opto-thermal properties are appealing from the standpoint of multimodal drug delivery, imaging and biosensing applications. Hydrophobic basal plane of sheets can be efficiently loaded with aromatic molecules via non-specific forces. With intense biomedical interest, methods are evolving to produce defect-free and dispersion stable sheets. This review summarizes advancements in synthetic approaches and strategies of stabilizing graphene derivatives in aqueous medium. We have described the interaction of colloidal graphene with cellular and sub-cellular components, and subsequent physiological signaling. Finally, a systematic discussion is provided covering toxicological challenges and possible solutions on utilizing graphene formulations for high-end biomedical applications.

Simultaneous Silicon Oxide Growth and Electrophoretic Deposition of Graphene Oxide

During electrophoretic deposition of graphene oxide (GO) sheets on silicon substrates, not only deposition but also simultaneous anodic oxidation of the silicon substrate takes place, leading to a three-layered material. Scanning electron microscopy images reveal the presence of GO sheets on the silicon substrate, and this is also confirmed by X-ray photoelectron spectroscopy (XPS), albeit that the carbon portion increases with increasing emission angle, hinting at a thin carbon layer. With increasing applied potential and increasing conductivity of the GO solution, the carbon signal decreases, whereas the overall thickness of the added layer formed on top of the silicon substrate increases. Through XPS spectra in which the Si 2p peaks shifted under those conditions to 103-104 eV, we were able to conclude that significant amounts of oxygen are present, indicative of the formation of an oxide layer. This leads us to conclude that GO can be deposited using electrophoretic deposition, but that at the same time, silicon is oxidized, which may overshadow effects previously assigned to GO deposition.

Understanding the enhanced electrical properties of free-standing graphene paper: the synergistic effect of iodide adsorption into graphene

Free-standing graphene (FSG) paper plays a vital role in a wide variety of applications as an electrode material. Specifically, the electrical properties of FSG are the most important factor affecting its use as an electrode material. Herein, the vacuum filtration technique is utilized to fabricate GO paper, which is then reductively treated with HI. Initially, the electrical conductivity is measured for GO papers with different thicknesses by varying the concentration of GO precursor as well as the reduction time. The FSG paper with a thickness of 3 microns exhibits the lowest sheet resistance and further characterization is carried out to reveal the origin of this enhancement of electrical properties. The low resistance is attributed to its crystalline nature, stacking height (L_c), in-plane crystallite size (L_a) and defect density (n_D). Meanwhile, iodide ions intercalated into the graphene layers act as hole-carriers, and their intercalation is favoured over adsorption at the surface.

Synergistic effect of electrical properties for tri-iodide adsorbed free-standing graphene paper upon different exposure time of GO papers in HI reducing agent for 0.5 hour (FSG1), 1 hour (FSG2) and 24 hour (FSG3).

Mangifera indica, Ficus religiosa and Polyalthia longifolia leaf extract-assisted green synthesis of graphene for transparent highly conductive film

A green approach to synthesize transparent conducting films of graphene nanosheets by reduction of graphene oxide is presented.

One-Step Process for High-Performance, Adhesive, Flexible Transparent Conductive Films Based on p-Type Reduced Graphene Oxides and Silver Nanowires

This work demonstrates a one-step process to synthesize uniformly dispersed hybrid nanomaterial containing silver nanowires (AgNWs) and p-type reduced graphene (p-rGO). The hybrid nanomaterial was coated onto a polyethylene terephthalate (PET) substrate for preparing high-performance flexible transparent conductive films (TCFs). The p-rGO plays the role of bridging discrete AgNWs, providing more electron holes and lowering the resistance of the contacted AgNWs; therefore, enhancing the electrical conductivity without sacrificing too much transparence of the TCFs. Additionally, the p-rGO also improves the adhesion between AgNWs and substrate by covering the AgNWs on the substrate tightly. The study shows that coating of the hybrid nanomaterials on the PET substrate demonstrates exceptional optoelectronic properties with a transmittance of 94.68% (at a wavelength of 550 nm) and a sheet resistance of 25.0 ± 0.8 Ω/sq. No significant variation in electric resistance can be detected even when the film was subjected to a bend loading with a radius of curvature of 5.0 mm or the film was loaded with a reciprocal tension or compression for 1000 cycles. Furthermore, both chemical corrosion resistance and haze effect were improved when p-rGO was introduced. The study shows that the fabricated flexible TCFs have the potential to replace indium tin oxide film in the optoelectronic industry.