Wetting transitions on rough surfaces revealed with captive bubble experiments. The role of surface energy

Adsorption of Acacia Gum on Self-Assembled Monolayer Surfaces: A Comprehensive Study Using QCM-D and MP-SPR

The interfacial structuring of Acacia gum at various pH values on self-assembled monolayer (SAM) surfaces was investigated in order to evaluate the respective importance of surface versus biopolymer hydration in the adsorption process of the gum. To this end, SAMs with four different ending chemical functionalities (-CH3, -OH, -COOH, and -NH2) were used on gold surfaces, and the gum adsorption was monitored using multiparametric surface plasmon resonance (MP-SPR) and quartz crystal microbalance with dissipation. Surface modification with alkanethiol and the subsequent adsorption of Acacia gum were also characterized by contact angle measurements using both sessile drop and captive bubble methods. According to MP-SPR results, this study demonstrated that gum adsorbed on all surfaces and that adsorption is the most favorable at both acid pH and hydrophobic environments, i.e., when both the surface and the biopolymer are weakly hydrated and more prone to interfacial dehydration. These results reinforce our recent proposal of interfacial dehydration-induced structuring of biopolymers. Increasing the pH logically decreased the adsorption capacity, especially on a hydrophilic surface, enhancing the hydration rate of the layer. A hydrophilic surface is unfavorable to Acacia gum adsorption except if the surface presents a negative surface charge. In this case, interfacial charge dehydration was promoted by attractive electrostatic interactions between the surface and biopolymers. In the aggregate, the water percentage and the viscoelastic properties were closely related to the properties of the surface function: the negative charge and hydrophobicity significantly increased the hydration rate and viscoelastic properties with the pH, while the positive charge induced a rigid and more dehydrated layer.

Wetting transitions in adhesive surfaces of polystyrene: The petal effect

HYPOTHESIS

The petal effect is a well-known natural phenomenon in surface science and has served as inspiration for the creation of several materials with superhydrophobic qualities and high adhesion. As surface roughness has a crucial role in these properties, being able to modulate it could help us design materials at will. Capillary penetration frustrates diffusion and promotes large contact angles as well as high adhesion.

EXPERIMENTS

Polystyrene surfaces were created using the spin-coating technique. By varying the polymer concentration, the surface roughness was modified. To determine the roughness parameters, atomic force microscopy was used. We recorded advancing and receding contact angles using water and glycerol as test liquids to study contact angle hysteresis, the work of adhesion and the apparent surface energy, which was determined with the Chibowski and Perea-Carpio method. For the purpose of elucidating the wetting states, captive bubble experiments were conducted.

FINDINGS

Using an easy method, we create polystyrene surfaces with both superhydrophobicity and strong adhesion, where the roughness area factor regulates wetting transitions from Cassie-Baxter to Wenzel. The receding contact angle suggests capillary penetration, which we demonstrate by captive bubble experiments. In addition, a link was found between the surface roughness and apparent surface energy.

Estimation of surface free energy at microstructured surface to investigate intermediate wetting state for partial wetting model

While partial wetting at nano-/microstructured surfaces can be described using the intermediate wetting state between the Cassie-Baxter and Wenzel states, the limitations of the partial wetting model remain unclear. In this study, we performed surface free energy analysis at a microstructured Si-water interface from both theoretical and experimental viewpoints. We experimentally measured the water contact angle on microstructured Si surfaces with square holes and compared the measured values with theoretical predictions. Furthermore, the surface free energy was analyzed using the effective wetting area estimated from the measured contact angle and electrochemical impedance spectroscopy results. We verified the validity of the partial wetting model for fabricated Si surfaces with a hole aperture a less than 230 μm and a hole height h of 12 μm, and for a < 400 μm, h = 40 μm. The model was found to be applicable to microstructured Si surfaces with a/h < 10.

Robust and durable liquid-repellent surfaces

This review provides a comprehensive summary of characterization, design, fabrication, and application of robust and durable liquid-repellent surfaces.

Impact of Hydrodynamic and Interfacial Interactions on Scale Formation in a Capillary Microchannel

This study proposes a model for the kinetics and hydrodynamics of gypsum scale deposition on surfaces of anhydrite, calcite, dolomite, and sandstone rocks while interacting with the brines of 3000 and 6000 mg/L [Ca²⁺] at 363 K and 1 atm. To do so, this study utilizes the surface energy characteristics of an interacting scale-brine-rock system as well as the geochemical interactions between brine-brine and brine-rock. The results showed that the deposition flux decreases steeply over time, followed by asymptotic propensity as time elapses. A higher degree of salinity in terms of [Ca²⁺] increases the deposition flux as much as 2.9-fold for the flowing velocity of 10^-6 m/s and 2.4-fold for a velocity of 10^-5 m/s. Moreover, higher flow velocity would lead to more deposition on sandstone followed by carbonate and anhydrite rocks: ∼2.6-fold for the salinity of 3000 mg/L and 2.2-fold for 6000 mg/L [Ca²⁺].

Oxygen Generation Using Catalytic Nano/Micromotors

Gaseous oxygen plays a vital role in driving the metabolism of living organisms and has multiple agricultural, medical, and technological applications. Different methods have been discovered to produce oxygen, including plants, oxygen concentrators and catalytic reactions. However, many such approaches are relatively expensive, involve challenges, complexities in post-production processes or generate undesired reaction products. Catalytic oxygen generation using hydrogen peroxide is one of the simplest and cleanest methods to produce oxygen in the required quantities. Chemically powered micro/nanomotors, capable of self-propulsion in liquid media, offer convenient and economic platforms for on-the-fly generation of gaseous oxygen on demand. Micromotors have opened up opportunities for controlled oxygen generation and transport under complex conditions, critical medical diagnostics and therapy. Mobile oxygen micro-carriers help better understand the energy transduction efficiencies of micro/nanoscopic active matter by careful selection of catalytic materials, fuel compositions and concentrations, catalyst surface curvatures and catalytic particle size, which opens avenues for controllable oxygen release on the level of a single catalytic microreactor. This review discusses various micro/nanomotor systems capable of functioning as mobile oxygen generators while highlighting their features, efficiencies and application potentials in different fields.

Impact of the equilibrium relationship between deposition and wettability behavior on the high-efficiency utilization of pesticides

BACKGROUND

Often, due to the occurrence of powdery mildew, cucumber leaf surfaces is changed into a more hydrophobic surface, which affects wetting and spreading of liquid pesticides, reducing their efficiency. The wetting and deposition behavior of liquid pesticides can be improved by adding surfactants to pesticides. Added surfactants affect the spray volume of the pesticide, which can lead to waste and a low utilization rate of the pesticide. It is important to further balance the relationship between deposition and wettability of pesticide liquid on the surfaces of healthy leaves and powdery mildew leaves of cucumber.

RESULTS

This study evaluated the deposition and wettability of hexaconazole (Hexa) with surfactants on the surfaces of healthy leaves and powdery mildew leaves of cucumber. The deposition rates of Hexa with surfactants were lower than that of Hexa due to the loss of solution in conventional spray volume (750 L ha^-1 ). The deposition rate of Hexa did not necessarily increase with increasing spray volume, and the deposition rate did not increase again after the spray volume increased to a certain level. Under the condition that the prevention and control effect were not reduced, we found that the volume of solution spray with added Silwet618 or AEO-5 should be adjusted to half of the normal volume, while the volume of solution spray with added 1227 or rosin-based quarternary ammonium should be adjusted to two-thirds of the normal volume to increase the deposition rate by approximately 30%. Regarding the wetting parameters, the results showed that the wettability of Hexa with Silwet618 was the best, but their combination was not ideal according to the composite index and deposition. By analyzing all the parameters, it was found that the spray volume reduction of Hexa with surfactant was approximately equal to the solution surface tension reduction, compared with the parameters of Hexa.

CONCLUSION

The equilibrium relationship between deposition rate and wetting parameters was determined to provide guidance for the application of surfactants and to lower the dosage of pesticides to increase their efficiency and reduce their application. © 2021 Society of Chemical Industry.

A generalized examination of capillary force balance at contact line: On rough surfaces or in two-liquid systems

We investigate the capillary force balance at the contact line on rough solid surfaces and in two-liquid systems. Our results confirm that solid-liquid interactions perpendicular to the interface have a significant influence on the lateral component of the capillary force exerted on the contact line. Surface roughness of the solid substrate reduces the mobility of liquid and alters how the perpendicular solid-liquid interactions transfer into a force acting parallel to the interface. A quantitative relation between surface roughness and the transfer strategy is proposed. Moreover, when a liquid is in coexistence with another immiscible liquid on a solid, the capillary forces exerted on liquids of both sides are involved in our theoretical model. The contact angle can be predicted by calculating three interfacial tensions. These arguments are then verified by molecular dynamics simulations. Our findings set up the generalized theoretical framework for the capillary force balance at the contact line and broaden its application in more realistic scenarios.

Revisiting the supplementary relationship of dynamic contact angles measured by sessile-droplet and captive-bubble methods: Role of surface roughness

HYPOTHESIS

Quantitative characterization of surface wettability through contact angle (CA) measurement using the sessile droplet (SD) or captive bubble (CB) methods is often limited by the intrinsic wetting properties of the substrate. Situations may arise when an extreme surface wettability may preclude using one of the two methods for predicting the behaviors of droplets or bubbles on the surface. This warrants a relationship between the dynamic CAs measured via the SD and CB methods. While the two dynamic CAs (e.g., the advancing CA of SD and receding CA of CB) add up to 180° on a smooth surface, the simple geometric supplementary principle may not apply for rough surfaces.

EXPERIMENTS

We perform a systematic wettability characterization of solid substrates with varying degrees of roughness using the sessile-droplet and captive-bubble methods, and interpret the experimental observations using a theoretical model.

FINDINGS

The dynamic contact angles measured by the sessile-droplet and captive-bubble methods deviate from the supplementary principle as the surface roughness is increased. We present a theoretical explanation for this disparity and predict the values of the contact angles using prevalent thermodynamic models of wetting and contact-angle hysteresis on rough substrates. The theoretical prediction is in good agreement with the experimental observations.

Amphiphilic hydrolyzable polydimethylsiloxane-b-poly(ethyleneglycol methacrylate-co-trialkylsilyl methacrylate) block copolymers for marine coatings. II. Antifouling laboratory tests and field trials

Poly(dimethylsiloxane) (PDMS) elastomer coatings containing an amphiphilic hydrolyzable diblock copolymer additive were prepared and their potential as marine antifouling and antiadhesion materials was tested. The block copolymer additive consisted of a PDMS first block and a random poly(trialkylsilyl methacrylate (TRSiMA, R = butyl, isopropyl)-co-poly(ethyleneglycol) methacrylate (PEGMA) copolymer second block. PDMS-b-TRSiMA block copolymer additives without PEGMA units were also used as additives. The amphiphilic character of the coating surface was assessed in water using the captive air bubble technique for measurements of static and dynamic contact angles. The attachment of macro- and microorganisms on the coatings was evaluated by field tests and by performing adhesion tests to the barnacle Amphibalanus amphitrite and the green alga Ulva rigida. All the additive-based PDMS coatings showed better antiadhesion properties to A. amphitrite larvae than to U. rigida spores. Field tests provided meaningful information on the antifouling and fouling release activity of coatings over an immersion period of 23 months.

Determination of Surface Energy Parameters of Hydrophilic Porous Membranes via a Corrected Contact Angle Approach

While the contact angle is a well-applied indicator of membrane hydrophobicity and surface energy, the interference of surface roughness and porosity in contact angle measurement and surface energy calculation has been long neglected in the field of porous membrane study. We propose an improved method to straightforwardly derive the surface energy of the porous membrane from contact angles with the interference effect corrected. A linearized model was established combining the Young-Dupré and Cassie-Baxter equations, from which the surface energy (Lifshitz-van der Waals and Lewis acid/base components) and roughness index (surface area difference) can be solved simultaneously at a given porosity using contact angles measured with a set of standard polar/nonpolar test liquids. The model solution was examined using hydrophilic microfiltration membranes with different pore morphologies (including perforated plate-like PCTE, irregular particulate bed-like PVDF, and fibrous mesh-like PTFE membranes), with the robustness of the results evaluated via Monte Carlo simulation. In comparison with the verified results of the model solution, it was found that the Lifshitz-van der Waals Lewis acid/base energy values for the tested membranes would deviate by 50-87, 30-160, and 52-97%, respectively, if surface roughness and porosity were neglected in the calculation. The profound effect of roughness and porosity on surface energy determination was further confirmed via theoretical analysis of the Young-Dupré and Cassie-Baxter relationships. This improved approach may apply to the surface energy characterization of hydrophilic rough porous membranes (e.g., hydrophilic microfiltration membranes).