Three-dimensional Cu/C porous composite: Facile fabrication and efficient catalytic reduction of 4-nitrophenol

A MOF@Metal Oxide Heterostructure Induced by Post-Synthetic Gamma-Ray Irradiation for Catalytic Reduction

Metal-organic framework (MOF) based heterostructures, which exhibit enhanced or unexpected functionality and properties due to synergistic effects, are typically synthesized using post-synthetic strategies. However, several reported post-synthetic strategies remain unsatisfactory, considering issues such as damage to the crystallinity of MOFs, presence of impure phases, and high time and energy consumption. In this work, we demonstrate for the first time a novel route for constructing MOF based heterostructures using radiation-induced post-synthesis, highlighting the merits of convenience, ambient conditions, large-scale production, and notable time and energy saving. Specifically, a new HKUST-1@Cu2O heterostructure was successfully synthesized by simply irradiating a methanol solution dispersed of HKUST-1 with gamma ray under ambient conditions. The copper source of Cu2O was directly derived from in situ radiation etching and reduction of the parent HKUST-1, without the use of any additional copper reagents. Significantly, the resulting HKUST-1@Cu2O heterostructure exhibits remarkable catalytic performance, with a catalytic rate constant nearly two orders of magnitude higher than that of the parent HKUST-1.

Covalent Grafting of Dielectric Films on Cu(111) Surface via Electrochemical Reduction of Aryl Diazonium Salts

Covalent grafting of dielectric films containing polyhedral oligomeric silsesquioxane (POSS) on the surface of Cu(111) is performed by a one-step electrochemical reduction of diazonium salts. This method is efficient and economic and performs in a proton-polar solvent of deionized water and tetrahydrofuran (THF), where the monomer employs an octavinylsilsesquioxane (OVS) containing a POSS core. The eight vinyl bonds contained in OVS are used to participate in aryl radical-initiated polymerization reactions to form films. The formed film is dense and covers the copper surface completely and uniformly. The thickness of the film can be controlled by adjusting the reaction time. The components of the films are mainly polynitrophenyl (PNP) or polyaminophenyl (PAP) as well as poly(octavinylsilsesquioxane) (POVS), and the POVS content could be adjusted by the applied voltage. The introduction of POSS prevents the copper surface from being oxidized and often gives the film good properties such as good dielectric properties, mechanical properties, and thermal properties. In addition, the presence of Cu-O-C and Cu-C bonds between the film and copper interface is confirmed at different film thicknesses by X-ray photoelectron spectroscopy (XPS), which allowed the construction of covalent bonds between metal and nonmetal, further enhancing the bonding between the film and copper. Organic films prepared by electrochemical reduction of diazonium salts using OVS as a monomer will have potential significance for the future development of the electronics industry.

Controllable Synthesis of Cobalt-Containing Nanosheet Array-Like Ternary CuCoAl-LDH/rGO Hybrids To Boost the Catalytic Efficiency for 4-Nitrophenol Reduction

A series of Co-doped ternary Cu_xCo_3-xAl-layered double hydroxide (LDH)/rGO nanosheet array hybrids (x = 0.5, 1.0, 1.5, and 2.0) were successfully prepared using the preconditioned pH value aqueous-phase coprecipitation strategy. The Cu_xCo_3-xAl-LDH/rGO hybrids are featured as hexagonal CuCoAl-LDH nanosheets in situ anchoring onto both sides of the rGO surface in an ab-plane vertically interlaced growth pattern. The Cu_xCo_3-xAl-LDH/rGO hybrids show excellent activity for the complete conversion of 4-nitrophenol to 4-aminophenol, especially Cu_1.5Co_1.5Al-LDH/rGO with the highest k_app value of 49.2 × 10^-3 s^-1 and TOF of 232.8 h^-1, clearly higher than most copper-containing samples in the literature and even some precious ones. Thermodynamic analysis was carried out, and the values of Ea, ΔH^#, ΔS^#, and ΔG^# were estimated. The best activity of Cu_1.5Co_1.5Al-LDH/rGO can be mainly ascribed to the in situ-formed ultrafine Cu₂O NPs (∼4.3 nm) along with a small amount of Cu⁰ species, the electron transfer effect induced by atomically dispersed Co²⁺ species leading to the formation of electron-rich Cu species along with the Co²⁺/Co³⁺ redox couple, the strong Cu₂O-CuCoAl-LDH-rGO synergy upon the nanosheet array morphology with a high surface area and pore volume, and enhanced adsorption of reactants upon π-π stacking via an rGO layer. Meanwhile, the Cu_1.5Co_1.5Al-LDH/rGO exhibits an excellent universality and good cycling stability for 10 continuous runs. The Cu_1.5Co_1.5Al-LDH/rGO also shows superior efficiency in the catalytic reduction of 4-NP solution with a high concentration (20 mM) and displays excellent reduction performance in the fixed-bed test, implying the potential applications of the current Co-doped hierarchical ternary Cu-based LDH/rGO hybrids in the continuous treatment of practical wastewater.

Atomically dispersed and oxygen deficient CuO clusters as an extremely efficient heterogeneous catalyst

Preparation of high-density and atomically-dispersed clusters is of great importance yet remains a formidable challenge, which precludes rational design of high-performance, ultrasmall heterogeneous catalysts for alleviating the energy and environmental crises. In this study, we demonstrated an appealing non-equilibrium growth model to give sub-2 nm CuO clusters not from the growth of nuclei but from the top-down growth of metastable bulk crystals. These CuO clusters have high density and intriguingly uniform orientation, and are atomically scattered on an inactive ultrathin AlOOH substrate, which has been driven by the lattice matching between the CuO clusters and the utlrathin AlOOH substrate. The catalytic activity of CuO clusters, with the hydrogenation of 4-nitrophenol as a model reaction, proved to be extremely efficient and showed a rate constant of 130.0 s^-1 g^-1, outperforming the commercial Pd/C catalysts and reported state-of-the-art noble-metal catalysts (1.89-117.2 s^-1 g^-1). These clusters have abundant interfacial oxygen vacancies (OVs) whose concentration can be regulated, and the OVs are found to be essential, according to density functional theory (DFT) calculations, in reducing the energy barrier of catalytic reduction and significantly boosting the catalytic reaction. These findings could add to the library of crystals downsized to the atomic level and demonstrate how engineering point defects on the sub-nanometer materials help design high-efficient catalysts.

Copper-Based Integral Catalytic Impeller for the Rapid Catalytic Reduction of 4-Nitrophenol

The integral catalytic impeller can simultaneously improve reaction efficiency and avoid the problem of catalyst separation, which has great potential in applying heterogeneous catalysis. This paper introduced a strategy of combining electroless copper plating with 3D printing technology to construct a pluggable copper-based integral catalytic agitating impeller (Cu-ICAI) and applied it to the catalytic reduction of 4-nitrophenol (4-NP). The obtained Cu-ICAI exhibits very excellent catalytic activity. The 4-NP conversion rate reaches almost 100% within 90 s. Furthermore, the Cu-ICAI can be easily pulled out from the reactor to be repeatedly used more than 15 times with high performance. Energy-dispersive spectrometry, X-ray diffraction, and X-ray photoelectron spectroscopy characterizations show that the catalyst obtained by electroless copper plating is a ternary Cu-Cu₂O-CuO composite catalyst, which is conducive to the electron transfer process. This low-cost, facile, and versatile strategy, combining electroless plating and 3D printing, may provide a new idea for the preparation of the integral impeller with other metal catalytic activities.

Cu/Cux S-Embedded N,S-Doped Porous Carbon Derived in Situ from a MOF Designed for Efficient Catalysis

The reasonable design of the precursor of a carbon-based nanocatalyst is an important pathway to improve catalytic performance. In this study, a simple solvothermal method was used to synthesize [Cu(TPT)(2,5-tdc)] ⋅ 2H₂ O (Cu-MOF), which contains N and S atoms, in one step. Further in-situ carbonization of the Cu-MOF as the precursor was used to synthesize Cu/Cu_x S-embedded N,S-doped porous carbon (Cu/Cu_x S/NSC) composites. The catalytic activities of the prepared Cu/Cu_x S/NSC were investigated through catalytic reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP). The results show that the designed Cu/Cu_x S/NSC has exceptional catalytic activity and recycling stability, with a reaction rate constant of 0.0256 s^-1 , and the conversion rate still exceeds 90 % after 15 cycles. Meanwhile, the efficient catalytic reduction of dyes (CR, MO, MB and RhB) confirmed its versatility. Finally, the active sites of the Cu/Cu_x S/NSC catalysts were analyzed, and a possible multicomponent synergistic catalytic mechanism was proposed.

Macro-meso-microporous carbon composite derived from hydrophilic metal-organic framework as high-performance electrochemical sensor for neonicotinoid determination

Electrochemical analysis enables pesticides monitoring become rapid and efficient. Herein, novel three dimensional nitrogen-doped macro-meso-microporous carbon composites (N/Cu-HPC) derived from polyvinylpyrrolidone (PVP) doped Cu-metal organic framework were successfully formed via one-pot solvothermal method followed by pyrolysis, which were further applied in high-performance electrochemical determination of neonicotinoid. The introduction of PVP endows the N/Cu-HPC good hydrophilicity preventing aggregation as well as more highly electronegative nitrogen species boosting electro-catalytic property dramatically. Interestingly, the macro-meso-microporous architecture improves mass and charge transports between neonicotinoid molecules and active sites such as Cu nanoparticles and carbon atoms possessing Lewis basicity next to pyridinic-N. Based on the N/Cu-HPC, imidacloprid (IDP), thiamethoxam (THA) and dinotefuran (DNF) were detected with wide linear detection ranges (0.5-60 μM for both IDP and DNF, 1-60 μM for THA) and low detection limits (0.026 μM for IDP, 0.062 μM for THA and 0.01 μM for DNF). Meanwhile, this sensor can be successfully used for determination of IDP, THA and DNF in oat, corn and rice with good recoveries (92.0-100.9%, RSD ≤ 4.8%), demonstrating that the N/Cu-HPC possesses a high potential to be an advanced sensing device for monitoring neonicotinoid in agricultural products.

Nitrogen-doped porous carbon-encapsulated copper composite for efficient reduction of 4-nitrophenol

Developing low-cost non-precious metals as efficient catalysts for the reduction of toxic 4-nitrophenol (4-NP) to useful 4-aminophenol (4-AP) have received increasing attention in recent years. Herein, a novel and efficient Cu-based catalyst Cu/Cu_xO@CN (carbon doped with nitrogen) was prepared via a facile method from pyrolysis of bi-ligand MOFs material Cu₂(BDC)₂(BPY) (BDC = p-Phthalic acid, BPY = 4,4'-bipyridyl) in Ar atmosphere. Characterization results revealed that N doping in carbon matrix favors the development of mesoporous structure, the formation of more defect sites in carbon matrix, better dispersion of Cu/Cu_xO nano particles, and maintenance of Cu species in metallic Cu state (the active site), all of which contribute to a superior catalytic activity for 4-NP reduction with a pseudo-first-order rate constant as high as 0.126 s^-1 (the molar ratio of NaBH₄ to 4-NP is 400), nearly 11 times higher than its counterpart Cu/Cu_xO@C without N doping (0.011 s^-1). The activation energy for 4-NP reduction to 4-AP catalyzed by Cu/Cu_xO@CN was determined as 55.6 kJ mol^-1 (the molar ratio of NaBH₄ to 4-NP is 100). In addition, Cu/Cu_xO@CN showed excellent reusability in successive 6 cycles. The facile synthesis and superior catalytic activity make Cu/Cu_xO@CN a promising catalyst in industrial applications for many other similar reaction systems.

Nitrogen, silicon co-doped carbon dots as the fluorescence nanoprobe for trace p-nitrophenol detection based on inner filter effect

P-nitrophenol (PNP) has been widely applied to industry processing for many purposes, but the persistence and toxicity of residuum may pose risks to human health. To analyze PNP in industrial and agricultural wastewater, a versatile fluorescent probe sensing platform was proposed. In this work, we devised a fluorescence approach that utilized nitrogen, silicon co-doped carbon dots (N,Si-CDs) to monitor PNP originating from the inner filter effect (IFE). The N,Si-CDs were generated in a one-step hydrothermal synthesis, and which possessed outstanding fluorescence signal and water-dispersity. Emission at 441 nm was monitored with excitation at 360 nm using a common spectrofluorometer. The method achieved an exceptionally low limit of detection (LOD) of 0.011 μM. Furthermore, this method not only eliminates the interference from metal ions and acid ions, but also provides a potential application prospect for N,Si-CDs in the field of water monitoring. Analysis of tap and lake water led to 93.30-106.30% recoveries and <1% relative standard deviation at 2.5-25 μM PNP concentrations.

Selective Hydrogenation of Biomass-Derived Furfural: Enhanced Catalytic Performance of Pd-Cu Alloy Nanoparticles in Porous Polymer

Here, the development of a new catalyst is reported for the selective furfural (FF) hydrogenation to furfuryl alcohol (FA) based on about 7 nm sized Pd-Cu alloy nanoparticles (NPs) formed in inexpensive, commercially available micro/mesoporous hypercrosslinked polystyrene (HPS). A comparison of the catalytic properties of as-synthesized and reduced (denoted "r") catalysts as well as Pd-Cu alloy and monometallic palladium NPs showed a considerable enhancement of the catalytic performance of Pd-Cu/HPS-r compared to other catalysts studied, resulting in about 100 % FF conversion, 95.2 % selectivity for FA and a TOF of 1209 h^-1 . This was attributed to the enrichment of the NP surface with copper atoms, disrupting the furan ring adsorption, and to the presence of both zerovalent and cationic palladium and copper species, resulting in optimal hydrogen and FF adsorption. These factors along with exceptional stability of the catalyst in ten consecutive catalytic cycles make it highly promising in practical applications.

Human hair catalyzed selective reduction of nitroarenes to amines

Nowadays, there is great demand to use natural, cheap, and biodegradable materials as catalysts in different organic reactions. In this work, we use human hair as a completely biodegradable, renewable, and available material for the reduction of nitroarenes in aqueous media at 50 °C. Using this new catalyst, structurally different aromatic nitro compounds, as well as heterocyclic compounds, are reduced to corresponding amines in high to excellent yields. The presented catalytic system is applicable for large-scale reduction of nitroarenes.

2D Mesoporous Channels of PMO; a Platform for Cluster-Like Pt Synthesis and Catalytic Activity in Nitrophenol Reduction

Thiourea-bridged organosiloxane is used to synthesize a periodic mesoporous organosilica (PMO). Since this PMO has an S-enriched surface, owing to thiourea functional groups, it exhibits strong coordination toward Pt ions, and it shows a high tunability in the Pt nanoparticles size. This hybrid mesoporous material is employed as a catalyst in the efficient reduction reaction of 4-nitrophenol to 4-aminophenol at room temperature in an aqueous media.

Core-shell structured Co@CN nanocomposites as highly efficient dual function catalysts for reduction of toxic contaminants and hydrogen evolution reaction

In this study, we have reported nitrogen-doped graphite C coated Co nanocomposite (Co@CN) catalysts synthesized by one-step arc discharge method. The surface compositions, morphologies and the catalytic properties of the Co@CN nanocomposites were studied minutely. The results reveal that the prepared Co@CN nanocomposites have typical core-shell structure and show highly efficient catalytic performance in a reduction of 4-nitrophenol (4-NP), rhodamine and methylene blue. Their rate constant (K_app) is 0.074 s^-1 in a reduction of 4-NP, which is much higher than that of reported transition metal-based catalysts. Moreover, the overpotential of Co@CN is only 96 mV at a current density of 10 mA cm^-2 in alkaline solution, showing high electrocatalytic activities in the hydrogen evolution reaction. The excellent synergistic effect between nitrogen-doped graphite C shell and magnetic Co core enables the Co@CN nanocomposites catalysts to hold abundant active sites and to transmit rapidly electron ability, resulting in Co@CN nanocomposite catalysts having a highly efficient catalytic nature.

Engineering CuOx–ZrO2–CeO2 nanocatalysts with abundant surface Cu species and oxygen vacancies toward high catalytic performance in CO oxidation and 4-nitrophenol reduction

CuO_x–ZrO₂–CeO₂ nanocrystalline catalysts were designed and synthesized by a solvent-free synthetic strategy, and exhibited excellent catalytic performance owing to the increased oxygen vacancies and better dispersed active metal species.