Understanding hemicellulose-cellulose interactions in cellulose nanofibril-based composites

Evaluating the reinforcing potential of enzymatic cellulose nanocrystals in polypropylene nanocomposite

Cellulose nanocrystals (CNCs) produced through enzymatic hydrolysis exhibit physicochemical properties that make them attractive as eco-friendly reinforcing agents in polymer composites. However, the extent of their efficacy within a polymeric matrix is yet to be fully established. This study investigated the reinforcing capabilities of enzymatic CNC (approximately 3 nm in diameter) isolated from bleached eucalyptus Kraft pulp (BEKP), focusing on its application in polypropylene (PP) nanocomposites produced by injection molding. The study compared the performance of this enzymatic CNC (1-5 % wt) with PP composites reinforced with micro-sized cellulose fibers (BEKP at 10-30 % wt, approximately 13 μm) and additionally with commercial CNC produced by sulfuric acid hydrolysis. Despite enzymatic CNC experiencing agglomeration during spray-drying, leading to an average diameter increase to 3 μm, it still significantly increased the crystallization and glass transition temperature of the PP matrix. However, this agglomeration likely hindered the improvement of the mechanical properties within the nanocomposites. The results also showed that enzymatic CNC provided higher thermal stability at lower reinforcement levels compared to BEKP, but this came with a reduction in stiffness, posing a significant consideration in composite design. The addition of a coupling agent greatly enhanced the dispersion of reinforcements and the interfacial adhesion within the matrix, contributing to the enhanced performance of the composite properties. Additionally, enzymatic CNC demonstrated potential for superior reinforcement efficacy compared to commercially available CNC produced by sulfuric acid hydrolysis. In conclusion, enzymatic CNC exhibited a promising role as nano-reinforcement for thermoplastic polymer nanocomposites, exhibiting higher thermal properties at lower reinforcing loads than traditional micro-sized fiber reinforcements. The absence of sulfur, coupled with its higher thermal stability and sustainable potential, positions enzymatic CNC as a particularly favorable choice for applications involving direct contact with food, cosmetics, pharmaceuticals, and biomedical materials.

Enhancing the dispersibility of Gelidium amansii-derived microfibrillated cellulose through centrifugal fractionation

Hydrothermal pretreatment is useful for microfibrillated cellulose (MFC) preparation due to its safety, but the remaining hemicellulose might affect MFC properties. This study aimed to investigate the effect of centrifugation time on hemicellulose removal and the physicochemical properties of MFC obtained after hydrothermal pretreatment and micro-fibrillation. In this study, centrifugation was applied to the MFC suspension at varying duration times. Composition analysis and Fourier transform infrared spectra indicated that fractionated MFC has no hemicellulose content after 10, 20, and 30 min centrifugation. It also showed an approximately 5 times higher than 0.5 % g/g of initial solid concentration, indicated by a lower gel concentration point, than unfractionated MFC. Scanning electron microscope images of the fractionated MFC for 30 min (MFC2C) presented thin, long cellulose fibrils of 517 nm in average diameter and 635-10,000 nm in length that induced a slower sedimentation rate. MFC2C dispersion was also improved by autoclave sterilization by regulating cellulose structure, rheology, and crystallinity. As a result, MFC dispersibility can be enhanced by removing hemicellulose through simple centrifugation.

A study of the properties of hemicelluloses adsorbed onto microfibrillar cellulose isolated from apple parenchyma

Binding assays of commercially available hemicelluloses and pectins, and microfibrillar cellulose isolated form apple parenchyma were prepared. Initial studies showed that among all of the non-cellulosic polysaccharides examined, only the hemicelluloses (xyloglucan, xylan, glucomannan, ß-d-glucan) showed the ability to adsorb to microfibrillar cellulose. Among several adsorption models tested, the best fit was obtained for the Redlich-Peterson isotherm. Moreover, the linear vs. the branched structure and the size of the hemicelluloses have an influence over the extent of the adsorption to cellulose. The Fourier Transform Infrared and Raman spectra showed that a rather weak interaction took place between the hemicelluloses and cellulose. Also, the differential scanning calorimetry and the light scattering method results showed that after adsorption, cellulose has less mobility. Moreover, the mechanical properties of cellulose films changed after the addition of the chosen hemicelluloses and the films became less elastic but more resistant to a breaking force.

Non-fuel applications of bio-oil for sustainability in management of bioresources

Biomass valorization by thermochemical conversion method is a promising and intriguing pathway due to the flexibility of utilizing a diverse group of biomass and biowastes, specific product delivery mechanism through manipulation of process parameters, and wide applicability of the products. Pyrolysis has been viewed as an effective valorization technique to transform biowastes into pyrolytic oil, solid char, and syngas. Syngas is generally fed to the pyrolysis process to generate heat necessary for the pyrolysis process to sustain. Pyrolysis may also be a subsidiary component in a biorefinery system where it draws feedstocks from refinery process residues or the side streams of the refinery operation. In recent times, pyrolysis products have been under intense research for their usability and diverse applicability. Bio-oil's rich chemical makeup has promising potential to be used as an advanced biofuel and is considered as a storehouse of diverse chemical species ranging from green solvents to bioactive chemicals. The current review provides a state of knowledge on non-fuel uses of bio-oil and concludes that the pyrolysis process and products could be a part of the future bioeconomy if designed in a manner that biowastes are transformed into value-added products which replace products of petroleum origin.

Bioinspired mechanically stable all-polysaccharide based scaffold for photosynthetic production

We demonstrate the construction of water-stable, biocompatible and self-standing hydrogels as scaffolds for the photosynthetic production of ethylene using a bioinspired all-polysaccharidic design combining TEMPO-oxidised cellulose nanofibers (TCNF) and a cereal plant hemicellulose called mixed-linkage glucan (MLG). We compared three different molecular weight MLGs from barley to increase the wet strength of TCNF hydrogels, and to reveal the mechanisms defining the favourable interactions between the scaffold components. The interactions between MLGs and TCNF were revealed via adsorption studies and interfacial rheology investigations using quartz crystal microbalance with dissipation monitoring (QCM-D). Our results show that both the MLG solution stability and adsorption behaviour did not exactly follow the well-known polymer adsorption and solubility theories especially in the presence of co-solute ions, in this case nitrates. We prepared hydrogel scaffolds for microalgal immobilisation, and high wet strength hydrogels were achieved with very low dosages of MLG (0.05 wt%) to the TCNF matrix. The all-polysaccharic biocatalytic architectures remained stable and produced ethylene for 120 h with yields comparable to the state-of-the-art scaffolds. Due to its natural origin and biodegradability, MLG offers a clear advantage in comparison to synthetic scaffold components, allowing the mechanical properties and water interactions to be tailored.

Sweet sorghum juice clarification and concentration: a review

Sweet sorghum is a promising biomaterial, considering its nutritional and energy value, unpretentiousness in cultivation and its promising economic parameters of processing. The concentrate of sweet sorghum juice is an outstanding material for food purposes, meeting the emerging trends of the industry. This review presents data on the physicochemical properties of sweet sorghum juice and sirup, as well as technological details on the processes of its pretreatment, clarification, and concentration. Physicochemical properties of raw juice of sweet sorghum, as well as purified juice and sirup, are discussed in terms of material pretreatment, methods of clarification and concentration, and storage conditions. Comprehensive theoretical principles, methodological details and explanations of the consistency of sweet sorghum juice processing are given. This work focuses entirely on the relationship between sweet sorghum juice treatment methods and its composition and provides versatile source of information for food science community, farmers, and entrepreneurs.

Sustainable hemp-based bioplastics with tunable properties via reversible thermal crosslinking of cellulose

Modern bioplastics and biocomposites frequently contain non-biodegradable or non-sustainable components and require complex recycling routes. Sustainable materials require integrating bio-based, cheap, widely available, recycled, or waste components. In order to incorporate these concepts, we selected hemp stalk waste, the industrial byproducts glycerol and xylan (hemicellulose), and citric acid as key components. Hemp stalks were processed into cast papers using only mechanical processes and no chemical modifications or pre-treatments. Cast papers were impregnated with a crosslinking mixture of glycerol, xylan, citric acid, and the plasticizer polyethylene glycol (PEG). Thermal crosslinking was performed as a single-step reaction by curing materials at 140 °C. All prepared bioplastics were washed in water for 48 h and extensively tested for water resistance and water absorption. A recycling route with depolymerization (for pulp recovery) in sodium hydroxide is demonstrated. A comprehensive analysis of crosslinking reaction is provided via FTIR and rheology, supplemented by structure analysis via SEM. A 7-fold reduction in water uptake was achieved compared to cast hemp paper. Obtained bioplastics, after washing in water, show elastic modulus up to 2.9 GPa, tensile strength up to 70 MPa, and elongation up to 4.3 %. As a result of component ratio variation, bioplastics achieve a high tuneability of properties ranging from brittle to ductile. Dielectric analysis indicates that bioplastics have the potential for application in electric insulation. A three-layer laminate is demonstrated as a concept for potential application as an adhesive for bio-based composites.

The Components' Roles in Thermal Stability and Flammability of Cork Powder

In this study, an analysis of the influence of extractives, suberin and lignocellulosic components on the pyrolysis decomposition and fire reaction mechanisms of a cork oak powder from Quercus suber L. is presented. The summative chemical composition of cork powder was determined. Suberin was the main component at 40% of the total weight, followed by 24% of lignin, 19% of polysaccharides and 14% of extractives. The absorbance peaks of cork and its individual components were further analyzed by means of ATR-FTIR spectrometry. Thermogravimetric analysis (TGA) showed that the removal of extractives from cork slightly increased the thermal stability between 200 °C and 300 °C and led to the formation of a more thermally stable residue at the end of the cork decomposition. Moreover, by removing suberin, a shift of the onset decomposition temperature to a lower temperature was noticed, indicating that suberin plays a major role in enhancing the thermal stability of cork. Furthermore, non-polar extractives showed the highest flammability with a peak of heat release rate (pHRR) of 365 W/g analyzed by means of micro-scale combustion calorimetry (MCC). Above 300 °C, the heat release rate (HRR) of suberin was lower than that of polysaccharides or lignin. However, below that temperature it released more flammable gases with a pHRR of 180 W/g, without significant charring ability, contrary to the mentioned components that showed lower HRR due to their prominent condensed mode of action that slowed down the mass and heat transfer processes during the combustion process.

Hemicellulolytic enzymes in lignocellulose processing

Lignocellulosic biomass is the most abundant source of carbon-based material on a global basis, serving as a raw material for cellulosic fibers, hemicellulosic polymers, platform sugars, and lignin resins or monomers. In nature, the various components of lignocellulose (primarily cellulose, hemicellulose, and lignin) are decomposed by saprophytic fungi and bacteria utilizing specialized enzymes. Enzymes are specific catalysts and can, in many cases, be produced on-site at lignocellulose biorefineries. In addition to reducing the use of often less environmentally friendly chemical processes, the application of such enzymes in lignocellulose processing to obtain a range of specialty products can maximize the use of the feedstock and valorize many of the traditionally underutilized components of lignocellulose, while increasing the economic viability of the biorefinery. While cellulose has a rich history of use in the pulp and paper industries, the hemicellulosic fraction of lignocellulose remains relatively underutilized in modern biorefineries, among other reasons due to the heterogeneous chemical structure of hemicellulose polysaccharides, the composition of which varies significantly according to the feedstock and the choice of pretreatment method and extraction solvent. This paper reviews the potential of hemicellulose in lignocellulose processing with focus on what can be achieved using enzymatic means. In particular, we discuss the various enzyme activities required for complete depolymerization of the primary hemicellulose types found in plant cell walls and for the upgrading of hemicellulosic polymers, oligosaccharides, and pentose sugars derived from hemicellulose depolymerization into a broad spectrum of value-added products.

Biobased Nanomaterials─The Role of Interfacial Interactions for Advanced Materials

This review presents recent advances regarding biomass-based nanomaterials, focusing on their surface interactions. Plant biomass-based nanoparticles, like nanocellulose and lignin from industry side streams, hold great potential for the development of lightweight, functional, biodegradable, or recyclable material solutions for a sustainable circular bioeconomy. However, to obtain optimal properties of the nanoparticles and materials made thereof, it is crucial to control the interactions both during particle production and in applications. Herein we focus on the current understanding of these interactions. Solvent interactions during particle formation and production, as well as interactions with water, polymers, cells and other components in applications, are addressed. We concentrate on cellulose and lignin nanomaterials and their combination. We demonstrate how the surface chemistry of the nanomaterials affects these interactions and how excellent performance is only achieved when the interactions are controlled. We furthermore introduce suitable methods for probing interactions with nanomaterials, describe their advantages and challenges, and introduce some less commonly used methods and discuss their possible applications to gain a deeper understanding of the interfacial chemistry of biobased nanomaterials. Finally, some gaps in current understanding and interesting emerging research lines are identified.

Cellulose: A Review of Water Interactions, Applications in Composites, and Water Treatment

Cellulose is known to interact well with water, but is insoluble in it. Many polysaccharides such as cellulose are known to have significant hydrogen bond networks joining the molecular chains, and yet they are recalcitrant to aqueous solvents. This review charts the interaction of cellulose with water but with emphasis on the formation of both natural and synthetic fiber composites. Covering studies concerning the interaction of water with wood, the biosynthesis of cellulose in the cell wall, to its dispersion in aqueous suspensions and ultimately in water filtration and fiber-based composite materials this review explores water-cellulose interactions and how they can be exploited for synthetic and natural composites. The suggestion that cellulose is amphiphilic is critically reviewed, with relevance to its processing. Building on this, progress made in using various charged and modified forms of nanocellulose to stabilize oil-water emulsions is addressed. The role of water in the aqueous formation of chiral nematic liquid crystals, and subsequently when dried into composite films is covered. The review will also address the use of cellulose as an aid to water filtration as one area where interactions can be used effectively to prosper human life.

Enzymes and enzymatic mechanisms in enzymatic degradation of lignocellulosic biomass: A mini-review

Enzymatic hydrolysis is the key step limiting the efficiency of the biorefinery of lignocellulosic biomass. Enzymes involved in enzymatic hydrolysis and their interactions with biomass should be comprehended to form the basis for looking for strategies to improve process efficiency. This article updates the contemporary research on the properties of key enzymes in the lignocellulose biorefinery and their interactions with biomass, adsorption, and hydrolysis. The advanced analytical techniques to track the interactions for exploiting mechanisms are discussed. The challenges and prospects for future research are outlined.

Effect of decoration route on the nanomechanical, adhesive, and force response of nanocelluloses-An in situ force spectroscopy study

Although cellulose derivatives are widely applied in high-tech materials, the relation between their force responses and their surface chemical properties in a biological environment as a function of pH is unknown. Here, interaction forces of surface modified cellulose nanocrystals (CNCs), lignin residual cellulose nanocrystals (LCNCs), and 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-oxidized cellulose nanofibres (TCNFs) with OSO3-, COO- and lignin chemical groups were measured using in situ peak force quantitative nanomechanical mapping and force spectroscopy in salt solution at two pH values. We found that the forces acting between the tip and CNC or LCNC are steric dominated showing long range and slow decay as a result of their low surface charge density. High Mw lignin contributed to the increased repulsion range for LCNCs compared to CNCs. The repulsion measured for TCNFs at the very short range was electrostatic force dominating showing a steep decay attributed to its high surface charge density. In the case of TCNFs, electrostatic double layer force was also evidenced by the attraction measured at secondary minima. In all the three cases the electro steric interactions are pH dependent. Dissipation maps verified that the force behavior for each material was related to structural conformation restriction of the groups at compression. The slow decayed repulsion of CNCs or LCNCs is related to a weak restriction of conformational change due to small surface groups or high molecular weight bound polymers forming flat layers, whereas the steep repulsion of TCNFs is attributed to a strong conformation restriction of carboxylic groups occurred by forming extended structure. Our results suggest that the force responses of the materials were dominated by surface charges and structural differences. TCNFs showed superior nanomechanical and repulsion properties over CNCs or LCNCs at neutral pH.

Wood Hemicelluloses as Innovative Wall Materials for Spray-Dried Microencapsulation of Berry Juice: Part 1—Effect of Homogenization Techniques on their Feed Solution Properties

The use of wood hemicelluloses, including galactoglucomannans (GGM) and glucuronoxylans (GX), in spray-dried microencapsulation of bioactive compounds has not been reported. Our study aims to investigate the benefits of spray-dried GGM and GX powders (sGGM and sGX) along with the effects of homogenization techniques (magnetic stirring, ultrasonication, and a combination of UltraTurrax homogenization and microfluidization) on the physicochemical properties of feed solutions (10–20%, w/w). Feed solutions of bilberry juice with sGGM, sGX, and mixtures of either sGGM or sGX with methylcellulose (MC) or carboxymethylcellulose (CMC) were examined to produce highly stable feed solutions for spray-dried microencapsulation. The effects of ultrasonication amplitudes (30–80%) on the viscosity and particle size distribution of sGGM feed solutions were more profound than observed in their sGX counterparts. Unlike sGX feed solutions, sGGM feed solutions homogenized by ultrasonication and microfluidization formed a gel-like structure. Microfluidization also caused a loss of total anthocyanin content (TAC) of the feed solutions. Magnetic stirring resulted in no gel formation and in the lowest viscosity of the feed solutions; hence, it is an effective method for preparing hemicellulose feed solutions. sGGM and sGX powders have high heat stability with melting temperatures of 170–180 °C. The sGGM + CMC combination was more stable over 1 week of storage than the sGGM and sGX feed solutions. Storing the feed solutions reduced TAC and increased sGGM viscosity. Our results indicated that GGM and GX have high potential for use as wall materials in the spray-dried microencapsulation of bioactive compounds.

The SGNH hydrolase family: a template for carbohydrate diversity

The substitution and de-substitution of carbohydrate materials are important steps in the biosynthesis and/or breakdown of a wide variety of biologically important polymers. The SGNH hydrolase superfamily is a group of related and well-studied proteins with a highly conserved catalytic fold and mechanism composed of 16 member families. SGNH hydrolases can be found in vertebrates, plants, fungi, bacteria, and archaea, and play a variety of important biological roles related to biomass conversion, pathogenesis, and cell signaling. The SGNH hydrolase superfamily is chiefly composed of a diverse range of carbohydrate-modifying enzymes, including but not limited to the carbohydrate esterase families 2, 3, 6, 12 and 17 under the carbohydrate-active enzyme classification system and database (CAZy.org). In this review, we summarize the structural and functional features that delineate these subfamilies of SGNH hydrolases, and which generate the wide variety of substrate preferences and enzymatic activities observed of these proteins to date.

Injectable thiol-ene hydrogel of galactoglucomannan and cellulose nanocrystals in delivery of therapeutic inorganic ions with embedded bioactive glass nanoparticles

We propose an injectable nanocomposite hydrogel that is photo-curable via light-induced thiol-ene addition between methacrylate modified O-acetyl-galactoglucomannan (GGMMA) and thiolated cellulose nanocrystal (CNC-SH). Compared to free-radical chain polymerization, the orthogonal step-growth of thiol-ene addition allows a less heterogeneous hydrogel network and more rapid crosslinking kinetics. CNC-SH reinforced the GGMMA hydrogel as both a nanofiller and a crosslinker to GGMMA resulting in an interpenetrating network via thiol-ene addition. Importantly, the mechanical stiffness of the GGMMA/CNC-SH hydrogel is mainly determined by the stoichiometric ratio between the thiol groups on CNC-SH and the methacrylate groups in GGMMA. Meanwhile, the bioactive glass nanoparticle (BaGNP)-laden hydrogels of GGMMA/CNC-SH showed a sustained release of therapeutic ions in simulated body fluid in vitro, which extended the bioactive function of hydrogel matrix. Furthermore, the suitability of the GGMMA/CNC-SH formulation as biomaterial resin to fabricate digitally designed hydrogel constructs via digital light processing (DLP) lithography printing was evaluated.

Cellulose extraction of Alstonia scholaris: A comparative study on efficiency of different bleaching reagents for its isolation and characterization

The incredible benefits of Alstonia scholaris are piquing researchers' attention in extracting its cellulose and utilizing it in further therapeutic applications. This study is based on cellulose extraction from its stalks and processed through chemical pre-treatments to manifest its cellulose content by using different bleaching reagents. A comparison was made on efficiencies of three reagents and it is found that the hydrogen peroxide exposed maximum cellulose than sodium hypochlorite and sodium chlorite. The experimental results revealed that A. scholaris possess 68-70% cellulose content. FTIR spectrum shows that OH- and CH- vibrations of cellulose appeared at 3320 cm-1 & 2892 cm-1 respectively whereas SEM images show fibrillation, rough surface, and lumens in bleached fiber that attributes to the removal of lignin and hemicelluloses and confirms cellulose extraction. The XRD pattern certifies the crystalline nature and compactness of cellulose whereas tensile properties and TGA help in understanding its flexibility, mechanical strength, and thermal stability at 370 °C respectively.

Kinetics and Thermodynamics of Hemicellulose Adsorption onto Nanofibril Cellulose Surfaces by QCM-D

The adsorption of hemicellulose derived from bagasse onto nanofibril cellulose has been studied in terms of kinetics and thermodynamics. In situ monitoring of bagasse hemicellulose with different molecular weights onto the nanofibril cellulose surfaces has been investigated using quartz crystal microbalance and dissipation. Then, the adsorption kinetics and thermodynamic properties were analyzed. Also, the sorption behavior and the adsorption layer properties were quantified in aqueous solutions. The maximum adsorption mass was 2.8314 mg/m2 at a concentration of 200 mg/L. Also, compared with that of the low-molecular-weight hemicellulose, the adsorption capacity of the high-molecular-weight hemicellulose was higher, and the adsorption rate changed faster and could reach an equilibrium in a shorter time. The intraparticle diffusion kinetic model represented the experimental data very well. Therefore, the kinetics of hemicellulose on the fiber adsorption was commonly described by a three-stage process: mass to transfer, diffusion, and equilibrium. The Gibbs energy change of the adsorption of hemicellulose was found to range from -20.04 to -49.75 kJ/mol at 25 °C. The entropy change was >0. It was found that the adsorption was spontaneous, and the adsorbed mass increased with the increase in temperature. This strengthened the conclusion that the adsorption process of the bagasse hemicellulose on the NFC was driven by the increase in entropy caused by the release of water molecules due to hydrophobic interaction or solvent reorganization.

Low temperature green extraction of Acer platanoides cellulose using nitrogen protected microwave assisted extraction (NPMAE) technique

Practicability of advanced and innovative techniques facilitates the high yield of cellulose extraction within a short period. The research aimed at the extraction of naturally abundant cellulose from Acer platanoides by "Nitrogen protected microwave assisted extraction (NPMAE)". The NPMAE uses microwaves for heating the sample and helps in fast extraction of cellulose in the presence of nitrogen atmosphere. Cellulose extraction was intensified by bleaching treatment in closed multimode NPMAE system at 100 W and 120 °C for 15 min. Experiment's result found that Acer platanoides fiber contains 70% cellulose content and diffferent analysis were studied for all chemically pre-treated fibers and found variations in results after each chemical treatment. The SEM results of bleached fibers show the rough surface due to the removal of lignin and hemicellulose. XRD pattern and FTIR analysis are in the favor of cellulose extraction and results show the presence of type I cellulose with 65% crystallinity index whileTGA and dTGA results explain that cellulose of Acer platanoides bleached fibers (APBF) is more thermally stable below 370 °C than other pre-treated fibers.

Lignin Inter-Diffusion Underlying Improved Mechanical Performance of Hot-Pressed Paper Webs

Broader use of bio-based fibres in packaging becomes possible when the mechanical properties of fibre materials exceed those of conventional paperboard. Hot-pressing provides an efficient method to improve both the wet and dry strength of lignin-containing paper webs. Here we study varied pressing conditions for webs formed with thermomechanical pulp (TMP). The results are compared against similar data for a wide range of other fibre types. In addition to standard strength and structural measurements, we characterise the induced structural changes with X-ray microtomography and scanning electron microscopy. The wet strength generally increases monotonously up to a very high pressing temperature of 270 °C. The stronger bonding of wet fibres can be explained by the inter-diffusion of lignin macromolecules with an activation energy around 26 kJ mol^-1 after lignin softening. The associated exponential acceleration of diffusion with temperature dominates over other factors such as process dynamics or final material density in setting wet strength. The optimum pressing temperature for dry strength is generally lower, around 200 °C, beyond which hemicellulose degradation begins. By varying the solids content prior to hot-pressing for the TMP sheets, the highest wet strength is achieved for the completely dry web, while no strong correlation was observed for the dry strength.

Recent Developments and Applications of Hemicellulose From Wheat Straw: A Review

Hemicellulose is an important component of plant cell walls, which is mainly used in biofuels and bioproducts. The hemicellulose extracted from different plant sources and plant locations has different microstructure and molecule. Wheat straw is an important biomass raw material for the extraction of hemicellulose. The aims of this review are to summary the recent developments and various applications of hemicellulose from wheat straw. The microstructure and molecule of hemicellulose extracted by different methods are comparably discussed. The hemicellulose-based derivatives and composites are also reviewed. Special attention was paid to the applications of hemicellulose such as biofuel production, packaging field, and adsorbent. The problems and developing direction were given based on our knowledge. We expect that this review will put forward to the development and high-value applications of hemicellulose from wheat straw.

Entropy drives the adsorption of xyloglucan to cellulose surfaces - A molecular dynamics study

The adsorption of nonionic polymers to cellulose is of large importance both in the plant cell wall during synthesis and for the development of sustainable materials from wood. Here, the thermodynamics of adsorption of the polysaccharide xyloglucan (XG) to both native and chemically modified cellulose with carboxyl groups was investigated using molecular dynamics simulations. The free energy of adsorption was calculated as the potential of mean force between an XG oligomer and model cellulose surfaces in a range of temperatures from 298 K to 360 K. It was found that the adsorption near room temperature is an endothermic process dominated by the entropy of released interfacial water molecules. This was corroborated by quantitative assessment of the absolute entropy per water molecule both at the interface and in the bulk. In the case of native cellulose, the adsorption became exothermic at higher temperatures, while the relatively strong interactions between water and the charged groups of the oxidized cellulose impede such a transition. The results also indicate that the extraction of strongly associated hemicelluloses would be facilitated by low temperature.

Cellulose Nanofibrils/Xyloglucan Bio-Based Aerogels with Shape Recovery

Bio-based aerogels containing cellulose nanofibrils (CNFs) are promising materials due to the inherent physical properties of CNF. The high affinity of cellulose to plant hemicelluloses (xyloglucan, xylan, pectin) is also an opportunity to develop biomaterials with new properties. Here, we prepared aerogels from gelled dispersions of CNFs and xyloglucan (XG) at different ratios by using a freeze-casting procedure in unidirectional (UD) and non-directional (ND) manners. As showed by rheology analysis, CNF and CNF/XG dispersions behave as true gels. We investigated the impact of the freezing procedure and the gel's composition on the microstructure and the water absorption properties. The introduction of XG greatly affects the microstructure of the aerogel from lamellar to cellular morphology. Bio-based aerogels showed high water absorption capacity with shape recovery after compression. The relation between morphology and aerogel compositions is discussed.

Wood hemicelluloses exert distinct biomechanical contributions to cellulose fibrillar networks

Hemicelluloses, a family of heterogeneous polysaccharides with complex molecular structures, constitute a fundamental component of lignocellulosic biomass. However, the contribution of each hemicellulose type to the mechanical properties of secondary plant cell walls remains elusive. Here we homogeneously incorporate different combinations of extracted and purified hemicelluloses (xylans and glucomannans) from softwood and hardwood species into self-assembled networks during cellulose biosynthesis in a bacterial model, without altering the morphology and the crystallinity of the cellulose bundles. These composite hydrogels can be therefore envisioned as models of secondary plant cell walls prior to lignification. The incorporated hemicelluloses exhibit both a rigid phase having close interactions with cellulose, together with a flexible phase contributing to the multiscale architecture of the bacterial cellulose hydrogels. The wood hemicelluloses exhibit distinct biomechanical contributions, with glucomannans increasing the elastic modulus in compression, and xylans contributing to a dramatic increase of the elongation at break under tension. These diverging effects cannot be explained solely from the nature of their direct interactions with cellulose, but can be related to the distinct molecular structure of wood xylans and mannans, the multiphase architecture of the hydrogels and the aggregative effects amongst hemicellulose-coated fibrils. Our study contributes to understanding the specific roles of wood xylans and glucomannans in the biomechanical integrity of secondary cell walls in tension and compression and has significance for the development of lignocellulosic materials with controlled assembly and tailored mechanical properties.

Hemicelluloses are an essential constituent of plant cell walls, but the individual biomechanical roles remain elusive. Here the authors report on the interaction of wood hemicellulose with bacterial cellulose during deposition and explore the resultant fibrillar architecture and mechanical properties.