Structural and morphological alterations induced by cobalt substitution in LaMnO3 perovskites

Decorated and reconstructed perovskite-oxide electrodes for oxygen electrocatalysis and Zn-air batteries

Although decorated nanoparticles offer a great potential to generate extra active sites, their preparation usually requires time- and energy-consuming approaches. We report the remarkable activity and durability augmentation for the oxygen evolution reaction (OER) via effective and facile on-site electrochemical manipulation, using LaNiO3 as a model catalyst. When compared to the pristine LaNiO3, the electrochemically manipulated LaNiO3 cycled in Fe3+-containing 0.1 M KOH (i.e., E-LNO+Fe) exhibits an almost three-fold improvement in current density at 1.65 V. It is experimentally and theoretically shown that the electrochemical manipulation leads to the creation of defective LaNiO3-δ and NiO on the surfaces, which accelerate phase transformation to (oxy)hydroxides and hence the OER. Furthermore, a Zn-air battery assembled with E-LNO+Fe has demonstrated superior activity by presenting 171 mW cm-2. Thus, our work demonstrates that substantial performance increases may be achieved by decorating and reconstructing perovskite-oxide electrodes via on-site electrochemical modification.

Non-Stoichiometric BaxMn0.7Cu0.3O3 Perovskites as Catalysts for CO Oxidation: Optimizing the Ba Content

In this work, a series of BaxMn0.7Cu0.3O3 samples (x: 1, 0.9, 0.8, and 0.7, BxMC) was synthesized, characterized, and used as catalysts for CO oxidation reaction. All formulations were active for CO oxidation in the tested conditions. A correlation between the electrical conductivity, obtained by impedance spectroscopy, and the reducibility of the samples, obtained by H2-TPR, was observed. The Ba0.8Mn0.7Cu0.3O3 composition (B0.8MC) showed the best catalytic performance (comparable to that of the 1% Pt/Al2O3 reference sample) during tests conducted under conditions similar to those found in the exhaust gases of current gasoline engines. The characterization data suggest the simultaneous presence of a high Mn(IV)/Mn(III) surface ratio, oxygen vacancies, and reduced copper species, these two latter being key properties for ensuring a high CO conversion percentage as both are active sites for CO oxidation. The reaction temperature and the reactant atmosphere composition seem to be the most important factors for achieving a good catalytic performance, as they strongly determine the location and stability of the reduced copper species.

Eco-Friendly Mechanochemical Synthesis of Bifunctional Metal Oxide Electrocatalysts for Zn-Air Batteries

The development of green and environmentally friendly synthesis methods of electrocatalysts is a crucial aspect in decarbonizing energy generation. In this study, eco-friendly mechanochemical synthesis of perovskite metal oxide-carbon black composites is proposed using different conditions and additives such as KOH. Furthermore, the optimization of ball milling conditions, including time and rotational speed, is studied. The mechanochemical synthesis in solid-state conditions without additives produces electrocatalysts that exhibit the highest bifunctional electrochemical activity towards both oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). Moreover, this synthesis demonstrates a lower Environmental Impact Factor (E-factor), indicating its greener nature, and due to its simplicity, it has a great potential for scalability. The obtained bifunctional electrocatalysts have been tested in a rechargeable zinc-air battery (ZAB) for 22 h with similar performance compared to the commercial catalyst (Pt/C) at significantly lower cost. These promising findings are attributed to the enhanced interaction between the perovskite metal oxide and carbon material and the improved dispersion of the perovskite metal oxide on the carbon materials.

Development of In Situ Methods for Preparing La-Mn-Co-Based Compounds over Carbon Xerogel for Oxygen Reduction Reaction in an Alkaline Medium

Metal oxides containing La, Mn, and Co cations can catalyze oxygen reduction reactions (ORRs) in electrochemical processes. However, these materials require carbon support and optimal interactions between both compounds to be active. In this work, two approaches to prepare composites of La-Mn-Co-based compounds over carbon xerogel were developed. Using sol-gel methods, either the metal-based material was deposited on the existing carbon xerogel or vice versa. The metal oxide selected was the LaMn0.7Co0.3O3 perovskite, which has good catalytic behavior and selectivity towards direct ORRs. All the as-prepared composites were tested for ORRs in alkaline liquid electrolytes and characterized by diverse physicochemical techniques such as XRD, XPS, SEM, or N2 adsorption. Although the perovskite structure either decomposed or failed to form using those in situ methods, the materials exhibited great catalytic activity, which can be ascribed to the strengthening of the interactions between oxides and the carbon support via C-O-M covalent bonds and to the formation of new active sites such as the MnO/Co heterointerfaces. Moreover, Co-Nx-C species are formed during the synthesis of the metal compounds over the carbon xerogel. These species possess a strong catalytic activity towards ORR. Therefore, the composites formed by synthesizing metal compounds over the carbon xerogel exhibit the best performance in the ORR, which can be ascribed to the presence of the MnO/Co heterointerfaces and Co-Nx-C species and the strong interactions between both compounds. Moreover, the small nanoparticle size leads to a higher number of active sites available for the reaction.

Enhancing the Performance of BaxMnO3 (x = 1, 0.9, 0.8 and 0.7) Perovskites as Catalysts for CO Oxidation by Decreasing the Ba Content

Mixed oxides featuring perovskite-type structures (ABO3) offer promising catalytic properties for applications focused on the control of atmospheric pollution. In this work, a series of BaxMnO3 (x = 1, 0.9, 0.8 and 0.7) samples have been synthesized, characterized and tested as catalysts for CO oxidation reaction in conditions close to that found in the exhausts of last-generation automotive internal combustion engines. All samples were observed to be active as catalysts for CO oxidation during CO-TPRe tests, with Ba0.7MnO3 (B0.7M) being the most active one, as it presents the highest amount of oxygen vacancies (which act as active sites for CO oxidation) and Mn (IV), which features the highest levels of reducibility and the best redox properties. B0.7M has also showcased a high stability during reactions at 300 °C, even though a slightly lower CO conversion is achieved during the second consecutive reaction cycle. This performance appears to be related to the decrease in the Mn (IV)/Mn (III) ratio.

Unlocking the chemical environment of nitrogen in perovskite-type oxides

Nitrogen (N) doping of perovskite-type oxides is an effective method for enhancing their photocatalytic performance. Quantitative and qualitative analyses of the doped N species are essential for a deeper understanding of the catalytic activity enhancement mechanism. However, examining the N environment in perovskite-type oxides, particularly in the bulk, using conventional analytical techniques, such as X-ray photoelectron spectroscopy (XPS), is challenging. In this study, we propose a new analytical technique, advanced temperature-programmed desorption (TPD) up to 1600 °C, to complement the conventional methods. TPD can quantify all N species in bulk oxides. Moreover, it facilitates chemical speciation of N environments, such as substitutional and interstitial N species. This is verified by XPS, CHN elemental analysis, X-ray absorption spectroscopy, and in situ diffuse reflectance infrared Fourier-transform spectroscopy. This study demonstrates the feasibility of advanced TPD as a new analytical method that offers comprehensive information on the N species within N-doped oxide materials at the bulk level.

Enhancing Interaction between Lanthanum Manganese Cobalt Oxide and Carbon Black through Different Approaches for Primary Zn-Air Batteries

Due to the need for decarbonization in energy generation, it is necessary to develop electrocatalysts for the oxygen reduction reaction (ORR), a key process in energy generation systems such as fuel cells and metal-air batteries. Perovskite-carbon material composites have emerged as active and stable electrocatalysts for the ORR, and the interaction between both components is a crucial aspect for electrocatalytic activity. This work explores different mixing methods for composite preparation, including mortar mixing, ball milling, and hydrothermal and thermal treatments. Hydrothermal treatment combined with ball milling resulted in the most favorable electrocatalytic performance, promoting intimate and extensive contact between the perovskite and carbon material and improving electrocatalytic activity. Employing X-ray photoelectron spectroscopy (XPS), an increase in the number of M-O-C species was observed, indicating enhanced interaction between the perovskite and the carbon material due to the adopted mixing methods. This finding was further corroborated by temperature-programmed reduction (TPR) and temperature-programmed desorption (TPD) techniques. Interestingly, the ball milling method results in similar performance to the hydrothermal method in the zinc-air battery and, thus, is preferable because of the ease and straightforward scalability of the preparation process.

Strategic Design and Insights into Lanthanum and Strontium Perovskite Oxides for Oxygen Reduction and Oxygen Evolution Reactions

Perovskite oxides exhibit bifunctional activity for both oxygen reduction (ORR) and oxygen evolution reactions (OER), making them prime candidates for energy conversion in applications like fuel cells and metal-air batteries. Their intrinsic catalytic prowess, combined with low-cost, abundance, and diversity, positions them as compelling alternatives to noble metal and metal oxides catalysts. This review encapsulates the nuances of perovskite oxide structures and synthesis techniques, providing insight into pivotal active sites that underscore their bifunctional behavior. The focus centers on the breakthroughs surrounding lanthanum (La) and strontium (Sr)-based perovskite oxides, specifically their roles in zinc-air batteries (ZABs). An introduction to the mechanisms of ORR and OER is provided. Moreover, the light is shed on strategies and determinants central to optimizing the bifunctional performance of La and Sr-based perovskite oxides.

Engineering dual-crystal configurations in perovskite oxides boosts electrocatalysis of lithium-oxygen batteries

Sculpting crystal configurations can vastly affect the charge and orbital states of electrocatalysts, fundamentally determining the catalytic activity of lithium-oxygen (Li-O2) batteries. However, the crucial role of crystal configurations in determining the electronic states has usually been neglected and needs to be further examined. Herein, we introduce orthorhombic and trigonal system into 0.5La0.6Sr0.4MnO3-0.5LaMn0.6Co0.4O3 (LSMCO) by selectively incorporating Sr and Co cations into the LaMnO3 framework during the sol-gel process, which is used to explore the relationship among crystal structure, electronic states and catalytic performance. Based on both experimental and theoretical calculations, the dual-crystal configurations induce strong lattice distortion, which promotes MnO6 octahedra vibration and shortened MnO bonds. Furthermore, the suppressed Jahn-Teller distortion weakens the orbital arrangement and accelerates the charge delocalization, leading to the conversion of Mn3+ to Mn4+ and optimized electronic states. Ultimately, this resulted in optimized Mn 3d and O 2p orbital hybridization and activated lattice oxygen function, leading to a significant improvement in electrocatalytic activity. The LSMCO catalyzed Li-O2 battery achieves enhanced discharge capacity of 14498.7 mAh/g and cycling stability of 258 cycles. This work highlights the significance of inner structure and presents a feasible strategy for engineering crystal configurations to boost electrocatalysis of Li-O2 batteries.

Sustainable Synthesis of Metal-Doped Lignin-Derived Electrospun Carbon Fibers for the Development of ORR Electrocatalysts

The aim of this work is to establish the Oxygen Reduction Reaction (ORR) activity of self-standing electrospun carbon fiber catalysts obtained from different metallic salt/lignin solutions. Through a single-step electrospinning technique, freestanding carbon fiber (CF) electrodes embedded with various metal nanoparticles (Co, Fe, Pt, and Pd), with 8-16 wt% loadings, were prepared using organosolv lignin as the initial material. These fibers were formed from a solution of lignin and ethanol, into which the metallic salt precursors were introduced, without additives or the use of toxic reagents. The resulting non-woven cloths were thermostabilized in air and then carbonized at 900 °C. The presence of metals led to varying degrees of porosity development during carbonization, improving the accessibility of the electrolyte to active sites. The obtained Pt and Pd metal-loaded carbon fibers showed high nanoparticle dispersion. The performance of the electrocatalyst for the oxygen reduction reaction was assessed in alkaline and acidic electrolytes and compared to establish which metals were the most suitable for producing carbon fibers with the highest electrocatalytic activity. In accordance with their superior dispersion and balanced pore size distribution, the carbon fibers loaded with 8 wt% palladium showed the best ORR activity, with onset potentials of 0.97 and 0.95 V in alkaline and acid media, respectively. In addition, this electrocatalyst exhibits good stability and selectivity for the four-electron energy pathway while using lower metal loadings compared to commercial catalysts.

Enhanced Photocatalytic Water Splitting of SrTiO3 Perovskite through Cobalt Doping: Experimental and Theoretical DFT Understanding

Throughout extensive research endeavors, SrTiO3 has emerged as a promising photocatalytic material for utilizing solar energy and facilitating hydrogen production via water splitting. Yet, the pursuit of enhanced efficiency and amplified hydrogen generation has prompted researchers to delve into the realm of advanced doping strategies. In this work, using experimental characteristics and DFT calculations, we studied the effect of cobalt substitution on the structural, electronic, optical, and magnetic properties as well as the photocatalytic activity of SrTi1-xCoxO3-δ (x = 0, 0.125, 0.25, 0.375, and 0.5) perovskites. The samples were successfully prepared by using the solid-state reaction method. Based on X-ray diffraction and the Rietveld refinement method, the elaborated samples were shown to preserve the absorption range up to the visible region. Moreover, the position of band edge levels after cobalt doping becomes more appropriate for water splitting. Our findings report that all cobalt-doped compounds exhibit good photocatalytic activities and could be used as suitable photocatalyst materials for hydrogen production.

Tailoring the Composition of BaxBO3 (B = Fe, Mn) Mixed Oxides as CO or Soot Oxidation Catalysts in Simulated GDI Engine Exhaust Conditions

Mixed oxides with perovskite-type structure (ABO₃) are promising catalysts for atmospheric pollution control due to their interesting and tunable physicochemical properties. In this work, two series of Ba_xMnO₃ and Ba_xFeO₃ (x = 1 and 0.7) catalysts were synthesized using the sol-gel method adapted to aqueous medium. The samples were characterized by μ-XRF, XRD, FT-IR, XPS, H₂-TPR, and O₂-TPD. The catalytic activity for CO and GDI soot oxidation was determined by temperature-programmed reaction experiments (CO-TPR and soot-TPR, respectively). The results reveal that a decrease in the Ba content improved the catalytic performance of both catalysts, as B0.7M-E is more active than BM-E for CO oxidation, and B0.7F-E presents higher activity than BF for soot conversion in simulated GDI engine exhaust conditions. Manganese-based perovskites (BM-E and B0.7M-E) achieve better catalytic performance than iron-based perovskite (BF) for CO oxidation reaction due to the higher generation of actives sites.

BaFe1−xNixO3 Catalysts for NOx-Assisted Diesel Soot Oxidation

In this work, it is analyzed the effect of the partial substitution of Fe by Ni in a BaFeO3 perovskite to be used as the catalyst for NOx-assisted diesel soot oxidation. A series of BaFe1−xNixO3 (x = 0, 0.2, 0.4 and 0.8) catalysts have been synthesized by using the sol–gel method. The catalysts have been characterized by ICP-OES, XRD, XPS, O2-TPD, H2-TPR- and TEM. The catalytic activity for NO to NO2 oxidation and NOx-assisted diesel soot oxidation have been determined by Temperature Programmed Reaction experiments (NOx -TPR and Soot-NOx-TPR, respectively) and by isothermal reaction at 450 °C. Ni seems not to be inserted in the BaFeO3 perovskite and, instead of that, BaNiO3 perovskite and NiO are detected on the surface of the perovskite BaFeO3. XPS data reveal the coexistence of Fe(III) and Fe(IV) on the catalyst’s surface (being Fe(III) the main oxidation state) and the presence of oxygen vacancies. All catalysts are active for NO oxidation to NO2, showing BaFeO3 and BaFe0.6Ni0.4O3 the best catalytic performance. BaFe0.6Ni0.4O3 shows the highest proportion of nickel on surface and it combines the highest activity and stability for NOx-assisted diesel soot oxidation. Also, this catalyst presents the highest initial soot oxidation rate which minimizes the accumulation of unreacted soot during reaction.

Transition metal oxides with perovskite and spinel structures for electrochemical energy production applications

Transition metal oxide-based materials are an interesting alternative to substitute noble-metal based catalyst in energy conversion devices designed for oxygen reduction (ORR), oxygen evolution (OER) and hydrogen evolution reactions (HER). Perovskite (ABO₃) and spinel (AB₂O₄) oxides stand out against other structures due to the possibility of tailoring their chemical composition and, consequently, their properties. Particularly, the electrocatalytic performance of these materials depends on features such as chemical composition, crystal structure, nanostructure, cation substitution level, e_g orbital filling or oxygen vacancies. However, they suffer from low electrical conductivity and surface area, which affects the catalytic response. To mitigate these drawbacks, they have been combined with carbon materials (e.g. carbon black, carbon nanotubes, activated carbon, and graphene) that positively influence the overall catalytic activity. This review provides an overview on tunable perovskites (mainly lanthanum-based) and spinels featuring 3d metal cations such as Mn, Fe, Co, Ni and Cu on octahedral sites, which are known to be active for the electrochemical energy conversion.

Recent advances in the heteroatom doping of perovskite oxides for efficient electrocatalytic reactions

Perovskite-type transition metal oxides have emerged as promising electrocatalysts for various electrocatalytic reactions owing to their low cost, compositional tunability and high stability. However, insufficient electrocatalytic activities of pristine perovskite oxides hinder their pathway towards real-world applications. The incorporation of heteroatoms into perovskite oxide structures has been regarded as an efficient way to improve the electrocatalytic performance. This minireview summarizes the recent advances in the heteroatom doping of perovskite oxides as efficient electrocatalysts for the hydrogen evolution reaction (HER), oxygen evolution reaction (OER) and oxygen reduction reaction (ORR). These heteroatom doping strategies are classified based on various types of doping sites. The mechanisms of improved electrocatalytic activities are discussed in detail within different doping sites and various kinds of dopants. Finally, the remaining challenges and perspectives are outlined for future developments of perovskite oxide-based catalysts.

Carbon Material and Cobalt-Substitution Effects in the Electrochemical Behavior of LaMnO3 for ORR and OER

LaMn_1−xCo_xO₃ perovskites were synthesized by a modified sol-gel method which incorporates EDTA. These materials’ electrochemical activity towards both oxygen reduction (ORR) and oxygen evolution reactions (OER) was studied. The cobalt substitution level determines some physicochemical properties and, particularly, the surface concentration of Co and Mn’s different oxidation states. As a result, the electroactivity of perovskite materials can be tuned using their composition. The presence of cobalt at low concentration influences the catalytic activity positively, and better bifunctionality is attained. As in other perovskites, their low electrical conductivity limits their applicability in electrochemical devices. It was found that the electrochemical performance improved significantly by physically mixing with a mortar the active materials with two different carbon black materials. The existence of a synergistic effect between the electroactive component and the carbon material was interpreted in light of the strong carbon–oxygen–metal interaction. Some mixed samples are promising electrocatalysts towards both ORR and OER.

B-Site modification of LaMn0.9Co0.1O3 perovskite using a selective dissolution method in C3H6 oxidation

LaMnCoO₃ is treated with HNO₃ to generate a Co-doped MnO₂ phase, which shows better catalytic performance than LaMnO₃ and pure MnO₂ catalysts for C₃H₆ oxidation.