Metal organic framework-derived 3D nanostructured cobalt oxide as an effective catalyst for soot oxidation

Enhanced Catalytic Soot Oxidation over Co-Based Metal Oxides: Effects of Transition Metal Doping

A series of Co-M (M = Fe, Cr, and Mn) catalysts were synthesized by the sol-gel method for soot oxidation in a loose contact mode. The Co-Fe catalyst exhibited the best catalytic activity among the tested samples, with the characteristic temperatures (T10, T50, and T90) of 470 °C, 557 °C, and 602 °C, respectively, which were 57 °C, 51 °C, and 51 °C lower than those of the CoOx catalyst. Catalyst characterizations of N2 adsorption-desorption, X-ray diffraction (XRD), X-ray photo-electron spectrometry (XPS), and the temperature programmed desorption of O2 (O2-TPD) were performed to gain insights into the relationships between the activity of catalytic soot oxidation and the catalyst properties. The content of Co2+ (68.6%) increased due to the interactions between Co and Fe, while the redox properties and the relative concentration of surface oxygen adsorption (51.7%) were all improved, which could significantly boost the activity of catalytic soot oxidation. The effects of NO and contact mode on soot oxidation were investigated over the Co-Fe catalyst. The addition of 1000 ppm of NO led to significant reductions in T10, T50, and T90 by 92 °C, 106 °C, and 104 °C, respectively, compared to the case without the NO addition. In the tight contact mode, the soot oxidation was accelerated over the Co-Fe catalyst, resulting in 46 °C, 50 °C, and 50 °C reductions in T10, T50, and T90 compared to the loose contact mode. The comparison between real soot and model Printex-U showed that the T50 value of real soot (455 °C) was 102 °C lower than the model Printex-U soot.

Unveiling the Surface Chemical Reactions during Multi-Phase Catalytic Oxidation of Soot on Nanoengineering/Interfacing/Doping-Prepared Mn-CeO2 Catalysts Using TG-MS and Operando DRIFTS-MS

The aerosol pyrolysis method from nitrate precursors was used to prepare the Mn-CeO2 catalyst containing Mn2O3, CeO2, and Mn-doped CeO2 nanoparticles for catalyzing carbonous soot oxidation. The prepared Mn-CeO2 catalysts have high specific surface areas, Ce3+ ratio, and oxygen vacancy defects; these are a benefit for soot oxidation. The T50 for soot oxidation on the 0.57Mn-CeO2 catalyst is as low as 355 °C, which is 329 °C lower than that for soot oxidation without a catalyst. The catalysts were characterized using XRD, SEM-EDS, HRTEM, XPS, Raman spectroscopy, H2-TPR-MS, O2-TPD-MS, soot-TPR-MS, and operando DRIFTS-MS. The functions of Mn2O3, CeO2, and Mn-doped CeO2 in the 0.57Mn-CeO2 catalyst are unveiled. Mn-doped CeO2 plays a key role and CeO2 participates in soot oxidation, while Mn2O3 is used to enhance higher ratios of Ce3+, via the reaction of Mn3+ + Ce4+ = Mn4+ + Ce3+. The mechanism of soot oxidation on Mn-CeO2 was proposed.

The decisive factor of hollow spherical network morphology of Nd1-xCexCo1-yCuyO3±δ perovskites towards soot oxidation

The perovskites Nd1-xCexCo1-yCuyO3 (x = 0–0.05, y = 0–0.1) have been synthesized using PVP-assisted sol–gel method and applied for soot oxidation reactions. XRD technique reveals the formation of orthorhombic phase with crystal volume of around ~ 214 Å3 and crystal size of ~ 25–40 nm. The interconnected nanoparticles with hollow spherical network morphology of particles are observed for the samples NdCoO3 (NC1) and Nd0.98Ce0.02Co0.95Cu0.05O3 (NC2) with particle sizes of around 300–500 nm. The samples experienced a charge transfer from ligand (O2−) to cobalt cation in UV region (210–260 nm) and also observed broad absorption bands in the visible region (380–600 nm). In addition, the bandgap energy of NC2 showed the lowest value (4.21 eV); as well as surface morphological advantage promoted the transport of surface-chemisorbed oxygen species in the inner and outer surface of catalysts surface due to the reducibility of the catalyst with the soot $$\left( {\frac{{{\text{O}}_{2}^{{{\text{x}} - }} }}{{{\text{O}}_{2}^{{{\text{x}} - }} + {\text{O}}^{2 - } }} = 0.90} \right)$$ O 2 x - O 2 x - + O 2 - = 0.90 . Furthermore, XPS results evidenced the higher content of Co2+ cation upon substitution of Ce/Cu into NC1, which successively formed more amount of Oβ-oxygen species. Remarkably, the perovskite NC2 showed the lowest soot oxidation temperature (T50% = 434 °C) among the investigated perovskites. Besides, the spherically networked morphology of NC2/NC1 samples also decided the soot oxidation process.

Enhanced Catalytic Soot Oxidation by Ce-Based MOF-Derived Ceria Nano-Bar with Promoted Oxygen Vacancy

As CeO2 is a useful catalyst for soot elimination, it is important to develop CeO2 with higher contact areas, and reactivities for efficient soot oxidation and catalytic soot oxidation are basically controlled by structures and surface properties of catalysts. Herein, a Ce-Metal organic framework (MOFs) consisting of Ce and benzene-1,3,5-tricarboxylic acid (H3BTC) is employed as the precursor as CeBTC exhibits a unique bar-like high-aspect-ratio morphology, which is then transformed into CeO2 with a nanoscale bar-like configuration. More importantly, this CeO2 nanobar (CeONB) possesses porou, and even hollow structures, as well as more oxygen vacancies, enabling CeONB to become a promising catalyst for soot oxidation. Thus, CeONB shows a much higher catalytic activity than commercial CeO2 nanoparticle (comCeO) for soot oxidation with a significantly lower ignition temperature (Tig). Moreover, while soot oxidation by comCeO leads to production of CO together with CO2, CeONB can completely convert soot to CO2. The tight contact mode also enables CeONB to exhibit a very low Tig of 310 °C, whereas the existence of NO also enhances the soot oxidation by CeONB to reduce the Tig. The mechanism of NO-assisted soot oxidation is also examined, and validated by DRIFTS to identify the formation and transformation of nitrogen-containing intermediates. CeONB is also recyclable over many consecutive cycles and maintained its high catalytic activity for soot oxidation. These results demonstrate that CeONB is a promising and easily prepared high-aspect-ratio Ce-based catalyst for soot oxidation.

Hierarchical ZIF-decorated nanoflower-covered 3-dimensional foam for enhanced catalytic reduction of nitrogen-containing contaminants

Metal Organic Frameworks (MOFs) represent a promising class of metallic catalysts for reduction of nitrogen-containing contaminants (NCCs), such as 4-nitrophenol (4-NP). Nevertheless, most researches involving MOFs for 4-NP reduction employ noble metals in the form of fine powders, making these powdered noble metal-based MOFs impractical and inconvenient for realistic applications. Thus, it would be critical to develop non-noble-metal MOFs which can be incorporated into macroscale and porous supports for convenient applications. Herein, the present study proposes to develop a composite material which combines advantageous features of macroscale/porous supports, and nanoscale functionality of MOFs. In particular, copper foam (CF) is selected as a macroscale porous medium, which is covered by nanoflower-structured CoO to increase surfaces for growing a cobaltic MOF, ZIF-67. The resultant composite comprises of CF covered by CoO nanoflowers decorated with ZIF-67 to form a hierarchical 3D-structured catalyst, enabling this ZIF-67@Cu foam (ZIF@CF) a promising catalyst for reducing 4-NP, and other NCCs. Thus, ZIF@CF can readily reduce 4-NP to 4-AP with a significantly lower E_a of 20 kJ/mol than reported values. ZIF@CF could be reused over 10 cycles and remain highly effective for 4-NP reduction. ZIF@CF also efficiently reduces other NCCs, such as 2-nitrophenol, 3-nitrophenol, methylene blue, and methyl orange. ZIF@CF can be adopted as catalytic filters to enable filtration-type reduction of NCCs by passing NCC solutions through ZIF@CF to promptly and conveniently reduce NCCs. The versatile and advantageous catalytic activity of ZIF@CF validates that ZIF@CF is a promising and practical heterogeneous catalyst for reductive treatments of NCCs.

Nickel and cobalt transfigured natural clay: a green catalyst for low-temperature catalytic soot oxidation

Modified 'natural clay' with Ni and Co nanoparticles explored as efficient catalyst for low-temperature soot oxidation activity studies.

Highly improved soot combustion performance over synergetic MnxCe1-xO2 solid solutions within mesoporous nanosheets

Constructing synergetic bimetal oxide solid solutions with exceptional catalytic performances for efficient soot elimination is becoming a research frontier in environmental catalysis. Herein, synergetic Mn_xCe_1-xO₂ solid solutions within mesoporous nanosheets, synthesized by a facile hydrothermal method for the first time, have been performed to catalyze the NO_x-assisted soot combustion. Research results validate that Mn_xCe_1-xO₂ solid solutions displayed highly improved soot combustion performance with respect to activity and selectivity, mainly due to the synergetic effect by combining factors of the unique mesoporous nanosheet-shaped feature, the enhanced chemical nature stemmed from high-valence Mn species, abundant active oxygen species originated from the enriched oxygen vacancies and the escalated redox properties. Furthermore, the enhanced NO_x storage and oxidation abilities, mainly derived from integrating reciprocal merits of high-valence Mn species and CeO₂, were also responsible for the highly improved soot combustion performance via NO_x-assisted mechanism. Moreover, Mn_xCe_1-xO₂ solid solutions also exhibited excellent reusability due to the unique morphological structure and stable crystal phase, showing good potential in practical applications.

Self-assembly of a highly stable and active Co3O4/H-TiO2 bulk heterojunction with high-energy interfacial structures for low temperature CO catalytic oxidation

Self-assembly of a highly stable and active Co₃O₄/H-TiO₂ bulk heterojunction with high-energy interfacial structures was realized for low temperature CO catalytic oxidation.