Two-dimensional/one-dimensional molybdenum sulfide (MoS2) nanoflake/graphitic carbon nitride (g-C3N4) hollow nanotube photocatalyst for enhanced photocatalytic hydrogen production activity

A green and environmentally benign route to synthesizing Z-scheme Bi2S3-TCN photocatalyst for efficient hydrogen production

Designing and developing photocatalysts with excellent performance in order to achieve efficient hydrogen production is an important strategy for addressing future energy and environmental challenges. Traditional single-phase photocatalytic materials either have a large bandgap and low visible light response or experience rapid recombination of the photogenerated carriers with low quantum efficiency, seriously hindering their photocatalytic applications. To solve these issues, an important solution is to construct well-matched heterojunctions with highly efficient charge separation capabilities. To this end, an in situ sulfurization reaction was adopted after the deposition of Bi3+ supramolecular complex on a layered supramolecular precursor of tubular carbon nitride (TCN). X-ray diffraction (XRD) patterns confirmed that the as-prepared sample has a good crystalline structure without any other impurities, while high-resolution transmission electron microscopy (HR-TEM) revealed that the heterojunction possesses a 2D structure with a layer of nano-array on its surface. Combined Fourier-transform infrared (FT-IR) spectra and energy-dispersive X-ray spectroscopy (EDX) revealed the interfacial interactions. Owing to the formation of the Z-scheme heterojunction, the visible light adsorption and the separation efficiency of the photo-generated carriers are both obviously enhanced, leaving the high energy electrons and high oxidative holes to participate in the photocatalytic reactions. As a result, the photocatalytic hydrogen evolution rate of Bi2S3-TCN achieves 65.2 μmol g-1·h-1. This proposed green and environmentally benign route can also be applied to construct other sulfides with 2D TCN, providing some important information for the design and optimization of novel carbon-nitride-based semiconductors.

Atomic-level investigation on significance of photoreduced Pt nanoparticles over g-C3 N4 /bimetallic oxide composites

Designing an effective photocatalyst for solar-to-chemical fuel conversion presents significant challenges. Herein, g-C3 N4 nanotubes/CuCo2 O4 (CN-NT-CCO) composites decorated with platinum nanoparticles (Pt NPs) were successfully synthesized by chemical and photochemical reductions. The size distribution and location of Pt NPs on the surface of CN-NT-CCO composites were directly observed by TEM. Extended X-ray absorption fine structure (EXAFS) spectra of Pt L3-edge for the above composite confirmed establishment of Pt-N bonds at an atomic distance of 2.09 Å in the photoreduced Pt-bearing composite, which was shorter than in chemically reduced Pt-bearing composites. This proved the stronger interaction of photoreduced Pt NPs with the CN-NT-CCO composite than chemical reduced one. The H2 evolution performance of the photoreduced (PR) Pt@CN-NT-CCO (2079 μmol h-1  g-1 ) was greater than that of the chemically reduced (CR) Pt@CN-NT-CCO composite (1481 μmol h-1  g-1 ). The abundance of catalytically active sites and transfer of electrons from CN-NT to the Pt NPs to participate in the hydrogen evolution are the primary reasons for the improved performance. Furthermore, electrochemical investigations and band edge locations validated the presence of a Z-scheme heterojunction at the Pt@CN-NT-CCO interface. This work offers unique perspectives on the structure and interface design at the atomic level to fabricate high-performance heterojunction photocatalysts.

Rational Design of Monolithic g-C3N4 with Floating Network Porous-like Sponge Monolithic Structure for Boosting Photocatalytic Degradation of Tetracycline under Simulated and Natural Sunlight Illumination

In order to solve the problems of powder g-C₃N₄ catalysts being difficult to recycle and prone to secondary pollution, floating network porous-like sponge monolithic structure g-C₃N₄ (FSCN) was prepared with a one-step thermal condensation method using melamine sponge, urea, and melamine as raw materials. The phase composition, morphology, size, and chemical elements of the FSCN were studied using XRD, SEM, XPS, and UV-visible spectrophotometry. Under simulated sunlight, the removal rate for 40 mg·L^-1 tetracycline (TC) by FSCN reached 76%, which was 1.2 times that of powder g-C₃N₄. Under natural sunlight illumination, the TC removal rate of FSCN was 70.4%, which was only 5.6% lower than that of a xenon lamp. In addition, after three repeated uses, the removal rates of the FSCN and powder g-C₃N₄ samples decreased by 1.7% and 2.9%, respectively, indicating that FSCN had better stability and reusability. The excellent photocatalytic activity of FSCN benefits from its three-dimensional-network sponge-like structure and outstanding light absorption properties. Finally, a possible degradation mechanism for the FSCN photocatalyst was proposed. This photocatalyst can be used as a floating catalyst for the treatment of antibiotics and other types of water pollution, providing ideas for the photocatalytic degradation of pollutants in practical applications.

Solar-induced efficient propylparaben photodegradation by nitrogen vacancy engineered reticulate g-C3N4: Morphology, activity and mechanism

Propylparaben (PrP) has attracted extensive concerns due to its wide occurrence in wastewater and potential health risk. Herein, nitrogen vacancy engineered reticulate g-C₃N₄ (Nv-RCN) was successfully synthesized for the photodegradation of PrP. Nv-RCN exhibited larger specific surface area, greater light absorption ability, higher transfer and separation efficiency of charge carriers in comparison with bulk g-C₃N₄ (CN). According to the characterization results and DFT calculation, nitrogen vacancy could capture electrons and facilitate oxygen adsorption. The Nv-RCN exhibited an outstanding PrP removal efficiency of 94.3 %, and the corresponding apparent rate constant of Nv-RCN was 3.37 times higher than that of CN. High O₂ concentration (8 mg/L) and low pH value (pH = 3) promoted PrP photodegradation based on Box-Behnken Design. The O₂^- was the major radical during PCOP of Nv-RCN, and could oxidize PrP by decarbonylation and dealkylation. This study provided new insights to the improvement of photodegradation performance of g-C₃N₄ for parabens removal and related environmental remediation.

Molecularly imprinted voltammetric sensor sensibilized by nitrogen-vacancy graphitized carbon nitride and Ag-MWCNTs towards the detection of acetaminophen

The overdose of acetaminophen (AP) can cause serious acute liver injury even the irreversible liver necrosis. The quantitative detection of AP is of great significance not only for clinical applications but also for the quantity control of its pharmaceutical formulations. In this paper, a sensitive molecularly imprinted voltammetric sensor towards AP was constructed based on synergistic enhancement of nitrogen-vacancy graphitized carbon nitride (NV-g-C₃ N₄ ) and carboxylated MWCNTs loaded with silver nanoparticles (Ag-MWCNTs). The powder X-Ray diffraction spectrum, field emission scanning and transmission electron microscopes, cyclic voltammetry (CV), and electrochemical impedance spectrum were used to characterize the composites. The results show that NV-g-C₃ N₄ and Ag-MWCNTs closely embedded each other, forming loose porous hybrid structure by hydrogen bond. The prepared sensor molecular imprinting polymer (MIP)/C₃ N₄ /Ag-CNTs/GCE shows a strong synergistic enhancement of electroanalytical response by CV and differential pulse voltammetry (DPV) tests when compared with NV-g-C₃ N₄ /GCE, Ag-CNTs/GCE, and MIP/GCE. Through the optimization of the ratio of monomer and template, electropolymerization cycle, elution cycle, incubation time, and pH, linear ranges of 0.007-5 and 5-100 μM were found with the limit of detection of 2.33 nM by DPV. Moreover, its selectivity towards AP was satisfied when compared with detection towards ascorbic acid, dopamine, and glucose. The recovery range of 96.3%-100.5% was obtained in the spiked human serum and urine samples with the SD below 3.0%. In addition, the prepared sensor shows great detecting robustness with good anti-interference, reproducibility, and stability.

2D/3D S-scheme heterojunction of carbon nitride/iodine-deficient bismuth oxyiodide for photocatalytic hydrogen production and bisphenol A degradation

A novel 2D/3D S-scheme carbon nitride/iodine-deficient bismuth oxyiodide (g-C₃N₄/BiO_1.2I_0.6) heterojunction was constructed for the first time by calcining a mixture of g-C₃N₄ nanosheets and flower-like BiOI. Irradiated by visible light, this g-C₃N₄/BiO_1.2I_0.6 heterojunction exhibited excellent photocatalytic hydrogen production and BPA degradation activity with high cycle stability. In particular, the photocatalytic activity of 0.2-C₃N₄/BiO_1.2I_0.6 could reach 1402.7 μmol g^-1 h^-1 (hydrogen production rate) and 0.01155 min^-1 (apparent rate of bisphenol A degradation), which were 3.5 and 3.2 times that of g-C₃N₄ respectively. The remarkable photocatalytic performance was due to the efficient charge separation of g-C₃N₄/BiO_1.2I_0.6 and the formation of S-scheme heterojunction, which maintained strong photocatalytic reduction and oxidation potentials. Noticeably, the charge density difference and band offsets of the g-C₃N₄/BiO_1.2I_0.6 were calculated. The results revealed that a built-in electric field (IEF) was created. The values of the valence band offset (ΔE_VBO) and the conduction band offset (ΔE_CBO) were -0.84 and -1.27 eV, respectively, which further demonstrated the formation of S-scheme photocatalytic charge transfer mechanism.

Development and Mechanistic Studies of Ternary Nanocomposites for Hydrogen Production from Water Splitting to Yield Sustainable/Green Energy and Environmental Remediation

Photocatalysts lead vitally to water purifications and decarbonise environment each by wastewater treatment and hydrogen (H2) production as a renewable energy source from water-photolysis. This work deals with the photocatalytic degradation of ciprofloxacin (CIP) and H2 production by novel silver-nanoparticle (AgNPs) based ternary-nanocomposites of thiolated reduce-graphene oxide graphitic carbon nitride (AgNPs-S-rGO2%@g-C3N4) material. Herein, the optimised balanced ratio of thiolated reduce-graphene oxide in prepared ternary-nanocomposites played matchlessly to enhance activity by increasing the charge carriers’ movements via slowing down charge-recombination ratios. Reduced graphene oxide (rGO), >2 wt.% or <2 wt.%, rendered H2 production by light-shielding effect. As a result, CIP degradation was enhanced to 95.90% by AgNPs-S-rGO2%@g-C3N4 under the optimised pH(6) and catalyst dosage(25 mg/L) irradiating beneath visible-light (450 nm, 150 watts) for 70 min. The chemical and morphological analysis of AgNPs-S-rGO2%@g-C3N4 surface also supported the possible role of thiolation for this enhancement, assisted by surface plasmon resonance of AgNPs having size < 10 nm. Therefore, AgNPs-S-rGO2%@g-C3N4 has 3772.5 μmolg−1 h−1 H2 production, which is 6.43-fold higher than g-C3N4 having cyclic stability of 96% even after four consecutive cycles. The proposed mechanism for AgNPs-S-rGO2%@g-C3N4 revealed that the photo-excited electrons in the conduction-band of g-C3N4 react with the adhered water moieties to generate H2.

Phosphor-Enhanced, Visible-Light-Storing g-C3N4/Ag3PO4/SrAl2O4:Eu2+,Dy3+ Photocatalyst Immobilized on Fractal 3D-Printed Supports

The combination of a phosphor with semiconductor photocatalysts can provide photoactivity in the dark. Indeed, the phosphor acts as a "light battery", harvesting photons during irradiation and later re-emitting light that can be used by the catalytic phase when in conditions of total darkness. This allows for continued activity of the composite catalyst, even in conditions of unstable light stimulation. In this study, we assess the use of a heterojunction, namely graphitic-C₃N₄/Ag₃PO₄, that enables efficient photoactivity specifically under visible light stimulation, in combination with a phosphor that exhibits green-blue phosphorescence (510 nm), that is SrAl₂O₄:Eu²⁺,Dy³⁺. Our findings showed that this combination was particularly interesting, noticeably displaying significant photoactivity in darkness, after short periods of activation by visible light. After finding the right combination and optimal ratios for maximum efficiency, the resulting catalyst composite was immobilized on resin supports with a fractal surface, printed by LCD-SLA 3D printing. The immobilization was effectuated via an aqueous-phase plasma-aided grafting (APPAG) process, using cold plasma discharge (CPD) and using vinylphosphonic acid (VPA) as a coupling agent. Whereas the colloidal photocatalyst displayed a serious problem of partial physical separation between the catalytic phase, g-C₃N₄/Ag₃PO₄, and the phosphor, the immobilization of the composite catalyst on polymer supports allowed solving this issue. Photodegradation assessments confirmed that the hybrid supported phosphor-enhanced catalyst was active, notably in dark conditions, as well as fairly photostable. This study offers new prospects for the fabrication of polymer-based panels for water purification, with round-the-clock activity and that are, in addition, extremely easy to recover and reuse, by comparison with colloidal catalysts.

Recent developments in architecturing the g-C3N4 based nanostructured photocatalysts: Synthesis, modifications and applications in water treatment

Water pollution is becoming an inevitable problem in today's world. Tons and tons of wastewater with hazardous pollutants are getting discharged into the clean water bodies every day. In this regard, photocatalytic environmental remediation using nanotechnology such as the use of organic, metal and non-metal based semiconductor photocatalysts for photodegradation of pollutants has gained enormous attention in the past few decades. This review is focused particularly on graphitic carbon nitride (g-C₃N₄) which is a cheap, metal-free, polymeric photoactive compound and it is used as a potential photocatalyst in wastewater treatment. Though, pristine g-C₃N₄ is a good photocatalyst, it has certain drawbacks such as poor visible light absorption capacity, quicker recombination of photoelectrons and holes, delayed mass and charge transfer, etc. As a result, the pristine g-C₃N₄ catalyst is modified into novel 0D, 1D, 2D and 3D morphologies such as nano-quantum dots, nanorods, nanotubes, nanowires, nanosheets, nanoflakes, nanospheres, nanoshells, etc. It was also tailored into novel composites along with various compounds through doping, metal deposition, heterojunction formation, etc., to enhance the photocatalytic property of pure g-C₃N₄. The modified catalysts showed promising photocatalytic performance such as degradation of majority of pollutants in the environment. It also showed excellent results in the removal or reduction of heavy metals. This review provides a detailed record of g-C₃N₄ and its diverse photocatalytic applications in the past years and it provides knowledge for the development of such similar novel compounds in the future.

MoS2 and Fe2O3 co-modify g-C3N4 to improve the performance of photocatalytic hydrogen production

Photocatalytic hydrogen production as a technology to solve energy and environmental problems exhibits great prospect and the exploration of new photocatalytic materials is crucial. In this research, the ternary composite catalyst of MoS2/Fe2O3/g-C3N4 was successfully prepared by a hydrothermal method, and then a series of characterizations were conducted. The characterization results demonstrated that the composite catalyst had better photocatalytic performance and experiment results had confirmed that the MoS2/Fe2O3/g-C3N4 composite catalyst had a higher hydrogen production rate than the single-component catalyst g-C3N4, which was 7.82 mmol g−1 h−1, about 5 times higher than the catalyst g-C3N4 (1.56 mmol g−1 h−1). The improvement of its photocatalytic activity can be mainly attributed to its enhanced absorption of visible light and the increase of the specific surface area, which provided more reactive sites for the composite catalyst. The successful preparation of composite catalyst provided more channels for carrier migration and reduced the recombination of photogenerated electrons and holes. Meanwhile, the composite catalyst also showed higher stability and repeatability.

Carbon Nitride Quantum Dot-Embedded Poly(vinyl alcohol) Transparent Thin Films for Greenish-Yellow Light-Emitting Diodes

Recently, freestanding polymer thin films encapsulated with nanostructures have attracted the significant attention of the scientific community due to their promising application in portable optoelectronic devices. In this research contribution, we have fabricated a freestanding polymer thin film of poly(vinyl alcohol) (PVA) encapsulated with carbon nitride quantum dots (CN-QDs) using the casting method, for the first time. The PVA polymer matrix provides mechanical support as well as dispersion of the CN-QDs preventing its solid-state quenching. From UV-visible spectra, it is revealed that optical transparency decreases with an increase in the concentration of CN-QDs within the PVA polymeric thin film. Such kind of decrease in optical transparency is one of the crucial factors for the optical concert of a nanomaterial. Interestingly, we have optimized the synthesis protocol to retain 40% transparency of the thin film by incorporating 10 wt % CN-QDs along with PVA without deteriorating its optical behavior. It is observed that when CN-QDs are embedded in the PVA matrix, emission becomes independent of excitation wavelength and is localized in the 510-530 nm region of the spectrum. Thus, the films exhibit excellent greenish-yellow emission when excited at 420 nm with the Commission Internationale de l'èclairage (CIE) coordinates (0.39, 0.46) and a correlated color temperature (CCT) of 4105 K. These excellent optoelectronic properties make them a promising candidate for practical phosphor applications. In a nutshell, this study demonstrates a promising way to exhibit the luminescence potential of freestanding polymer/CN-QD films in CN-QD-based solid-state lighting systems.

New g-C3N4/GO/MoS2 composites as efficient photocatalyst for photocathodic protection of 304 stainless steel

Photocathodic protection is an economical and environmental metal anticorrosion method. In this research, we successfully synthesized the g-C₃N₄/GO (15 wt%)/MoS₂ catalytic materials by a facile hydrothermal method. The results show that the as-prepared g-C₃N₄/GO (15 wt%)/MoS₂ composites prominently enhanced photocatalytic activities for the photocathodic protection of 304 stainless steel (SS) compared with the corresponding pristine g-C₃N₄ and MoS₂. Notably, the AC impedance results demonstrated that the Rct value of 304 SS coupled with g-C₃N₄/GO (15 wt%)/MoS₂ decreased to 35.66 Ω•cm², which is 29 and 37 times lower than that of g-C₃N₄ and MoS₂ alone. In addition, g-C₃N₄/GO (15 wt%)/MoS₂ provided the highest current density (77.19 μA•cm²) for the 304 SS, which is four times that of pristine g-C₃N₄. All results indicate that as-prepared g-C₃N₄/GO (15 wt%)/MoS₂ photocatalysts have produced a distinct enhancement on photocathodic protection performance. An optimum decorating amount of MoS₂ onto g-C₃N₄ forms heterojunctions of g-C₃N₄/MoS₂, which favor the separation of electrons and holes efficiently. Furthermore, the addition of GO further promotes the separation and transfer of photo-induced carriers.

Construction of 2D/2D MoS2/g-C3N4 Heterostructures for Photoreduction of Cr (VI)

2D/2D MoS₂/g-C₃N₄ (MCN) surface heterostructures were created by second thermal polymerization of bulk g-C₃N₄ and the reaction of thiourea and MoO₃ at 670 °C. MoS₂ networks grew vertically along the (002) facet on superior thin g-C₃N₄ nanosheets. The layered heterostructures drastically improved the Cr(VI) removal ability. In the dark case, 27% of Cr(VI) was removed within 45 min. The result indicates that the adsorption of Cr(VI) was a chemical adsorption process involving the sharing and transfer of electrons. The equilibrium data indicate that the adsorbent was covered with a monolayer adsorbate, which conformed to the Langmuir isotherm model (R² = 0.9618). In addition, MCN nanocomposites could convert Cr(VI) into non-toxic Cr(III) by photoreduction under visible light irradiation. With an optimized composition, 100% of Cr(VI) was removed within 30 min, which was ∼10 times quicker compared with Cr(VI) removal under dark conditions. Because g-C₃N₄ nanosheets (sample CN₆₇₀) with higher photocurrent density revealed the lowest photoreduction Cr(VI) ability, adsorption plays an important role in Cr(VI) removal. For MoS₂/g-C₃N₄ nanocomposites used in Cr(VI) removal, adsorption and photoreduction were incorporated together to get excellent performance.

Robust charge carrier by Fe3O4 in Fe3O4/WO3 core-shell photocatalyst loaded on UiO-66(Ti) for urea photo-oxidation

In this study, a facile four-step hydrothermal method was utilized to deposit a core-shell structure on UiO-66(Zr/Ti) nanoflake (NFs) as a visible-light-driven photocatalyst. The core was magnetic Fe₃O₄ which served as a charge carrier coated with WO₃ shell. The as-prepared photocatalyst was characterized by XRD, VSM, BET, FTIR, FE-SEM, UV-Vis-DRS, and PL techniques which proved successful deposition of Fe₃O₄@WO₃ core/shell particle on UiO-66(Zr/Ti)-NFs. The obtained photocatalyst was subsequently applied for urea photo-oxidation. This magnetically recoverable photocatalyst exhibited superior activity due to its desirable band alignment, high stability, and generation of the photo-induced charge carriers, as well as providing a high surface area with low mass transfer resistance. Fe₃O₄ core acted as charge-carrier to transport the photogenerated charges of UiO-66(Zr/Ti)-NFs (electron-donor) to WO₃ charge-collectors for effective photoconversion. The central composite design was applied to design the experiments matrix in which flow rate, pH, irradiation time, catalyst mass, and initial urea concentration were considered as operational factors. The optimized condition was found by defining the desirability function. 90% degradation percentage was achieved at 550 mL/min solution flowrate, pH = 7, 120 min irradiation time, 0.22 g UiO-66(Zr)-NFs-Fe₃O₄@WO_3, and 40 mg/L of the initial concentration of urea with the desirability value of 0.89. Such a superior photocatalytic activity of UiO-66-Fe₃O₄@WO₃ can be ascribed to the reclamation of Fe₃O₄ as a low bandgap carrier, which accelerated the conveyance of electrons and followed surpassing charge separation. Our present findings open a new strategy to produce a wide range of core-shell heterogeneous catalysts to be applied in photoreactors scale-up.

Graphitic carbon nitride nanotubes: a new material for emerging applications

We provide a critical review of the current state of the synthesis and applications of nano- and micro-tubes of layered graphitic carbon nitride. This emerging material has a huge potential for light-harvesting applications, including light sensing, artificial photosynthesis, selective photocatalysis, hydrogen storage, light-induced motion, membrane technologies, and can become a major competitor for such established materials as carbon and titania dioxide nanotubes. Graphitic carbon nitride tubes (GCNTs) combine visible-light sensitivity, high charge carrier mobility, and exceptional chemical/photochemical stability, imparting this material with unrivaled photocatalytic activities in photosynthetic processes, such as water splitting and carbon dioxide reduction. The unique geometric GCNT structure and versatility of possible chemical modifications allow new photocatalytic applications of GCNTs to be envisaged including selective photocatalysts of multi-electron processes as well as light-induced and light-directed motion of GCNT-based microswimmers. Closely-packed arrays of aligned GCNTs show great promise as multifunctional membrane materials for the light energy conversion and storage, light-driven pumping of liquids, selective adsorption, and electrochemical applications. These emerging applications require synthetic routes to GCNTs with highly controlled morphological parameters and composition to be available. We recognize three major strategies for the GCNT synthesis including templating, supramolecular assembling of precursors, and scrolling of nano-/microsheets, and outline promising routes for further progress of these approaches in the light of the most important emerging applications of GCNTs.

Short-range ordered Co(OH)2/TiO2 for boosting sulfite oxidation: Performance and mechanism

Catalysis of magnesium sulfite (MgSO₃) oxidation is crucial for the flue gas desulfurization by magnesium oxide. Here, a short-range ordered Co(OH)₂/TiO₂ hybrid with a direct Z-scheme band structure, was fabricated for the reaction of MgSO₃ oxidation. The abundant defects of Co(OH)₂/TiO₂ induced the generation of more surface adsorbed oxygen species, and therefore greatly facilitated the formation of the key radical of SO₅^- to enhance MgSO₃ oxidation. The oxidation rate of MgSO₃ was enhanced 6.1-fold higher than the uncatalyzed benchmark with this neat Co(OH)₂/TiO₂ catalyst. Moreover, the oxidation rate of MgSO₃ could be further improved 11.3-fold by the assistance of light irradiation, which broadened the pathways for MgSO₃ oxidation by inspiring more active radicals (O₂^-, OH, SO₄^-, SO₅^-) and photogenerated holes to participate into MgSO₃ oxidation. The photogenerated holes were proved to play key role to accelerate reaction by directly oxidized MgSO₃ or inducing active radicles, and the highly efficient utilization of photogenerated holes was guaranteed by the Z-scheme charge transfer in the Co(OH)₂/TiO₂ interface. The results provided by this study could serve as an environmentally friendly approach to improve the overall performance of wet desulfurization.