Rod-like Ni0.5Co0.5C2O4·2H2O in-situ formed on rGO by an interface induced engineering: Extraordinary rate and cycle performance as an anode in lithium-ion and sodium-ion half/full cells

The "dual-layer sulfur cathode" strategy: An In2S3/Bi2S3@rGO heterostructure as an interlayer/modified separator for boosting the areal capacities of lithium-sulfur batteries

The specific energies and energy densities of lithium-sulfur (Li-S) batteries are influenced by various cell parameters, including the sulfur loading, the sulfur weight percentage in the cathode, and the electrolyte/sulfur ratio. An In2S3/Bi2S3@rGO heterostructure was obtained by growing indium sulfide nanoparticles on the surface of bismuth sulfide nanoflowers in a graphene oxide (GO) solution via a one-step solvothermal approach. This structure was introduced as a modified separator/dual-layer sulfur cathode for Li-S batteries. The Bi2S3/In2S3 heterointerfaces act as active sites to speed up interfacial electron transfer, along with the entrapment, diffusion, and transformation of lithium polysulfides. A Li-S cell containing a dual-layer sulfur cathode (thin layer of In2S3/Bi2S3@rGO sandwiched between two thick layers of sulfur) and coupled with an In2S3/Bi2S3@rGO-coated separator suppressed the polysulfide shuttle effect. The cell based on the dual-layer sulfur cathode technology and operated at a current rate of 0.3C achieved a high capacity (7.1 mAh cm-2) after the 200th cycle, giving an electrolyte/sulfur ratio (10 µL mg-1) under a high sulfur loading (11.53 mg cm-2). These results demonstrate the unique nature of the dual-layer sulfur cathode technique, which can yield high energy density Li-S batteries with high sulfur loadings and low electrolyte/sulfur ratios.

Achieving ultrastability and efficient lithium storage capacity with high-energy iron(II) oxalate anode materials by compositing Ge nano-conductive sites

Transition metal oxalates (TMOxs, represented by iron oxalate) have attracted considerable interest in anode materials due to their excellent lithium storage properties and consistent cyclic performance. Although investigations into their electrochemical capabilities and lithium storage mechanisms are gradually deepening, the complex and varied electrochemical reactions in the initial cycle, poor inherent conductivity, and high irreversible capacity constrain their further development. Herein, to solve the above-mentioned problems, we controlled the hydrothermal synthesis conditions of iron oxalate with the assistance of organic solvents, which induced the growth of iron oxalate crystals with nano Ge metal as the core. The metal Ge space sites compounded to the stacked iron oxalate particles act as conductive nodes and metal frames, which enhances both the strength of iron oxalate samples and electronic conductivity and lithium-ion diffusion inside the electrode materials. This special structure enhances the electrochemical activity of iron oxalates and improves their lithium storage capability. The iron oxalate @ nano Ge metal composite (FCO@Ge-1) exhibits an excellent cycling performance and an appreciable reversible specific capacity (1090 mA h g^-1 after 200 cycles at 1 A g^-1). The obvious polarization and variation of the electrochemical reaction in the initial cycle of iron oxalate are reduced by compositing nano Ge metal. It is demonstrated that nano Ge metal can promote reversible capacity retention from 67.72% to 80.69% in the early cycles. The distinctive structure of iron oxalate @ nano Ge metal composite provides a fresh pathway to enhance oxalate electrochemical reversible lithium storage activity and develop high-energy electrode material by constructing composite space conductive sites.

High Pseudocapacitance-Driven CoC2 O4 Electrodes Exhibiting Superior Electrochemical Kinetics and Reversible Capacities for Lithium-Ion and Lithium-Sulfur Batteries

In this study, cuboid-like anhydrous CoC₂ O₄ particles (CoC₂ O₄ -HK) are synthesized through a potassium citrate-assisted hydrothermal method, which possess well-crystallized structure for fast Li⁺ transportation and efficient Li⁺ intercalation pseudocapacitive behaviors. When being used in lithium-ion batteries, the as-prepared CoC₂ O₄ -HK delivers a high reversible capacity (≈1360 mAh g^-1 at 0.1 A g^-1 ), good rate capability (≈650 mAh g^-1 at 5 A g^-1 ) and outstanding cycling stability (835 mAh g^-1 after 1000 cycles at 1 A g^-1 ). Characterizations illustrate that the Li⁺ -intercalation pseudocapacitance dominates the charge storage of CoC₂ O₄ -HK electrode, together with the reversible reaction of CoC₂ O₄ +2Li⁺ +2e^- →Co+Li₂ C₂ O₄ on discharging and charging. In addition, CoC₂ O₄ -HK particles are also used together with carbon-sulfur composite materials as the electrocatalysts for lithium-sulfur (Li-S) battery, which displays a gratifying sulfur electrochemistry with a high reversibility of 1021.5 mAh g^-1 at 2 C and a low decay rate of 0.079% per cycle after 500 cycles. The density functional theory (DFT) calculations show that CoC₂ O₄ /C can regulate the adsorption-activation of reaction intermediates and therefore boost the catalytic conversion of polysulfides. Therefore, this work presents a new prospect of applying CoC₂ O₄ as the high-performance electrode materials for rechargeable Li-ion and Li-S batteries.

Active Sulfur-Host Material VS4 with Surface Defect Engineering: Intercalation-Conversion Hybrid Cathode Boosting Electrochemical Performance of Li-S Batteries

Transition-metal sulfides as late-model electrocatalysts usually remain inactive in lithium-sulfur (Li-S) batteries in spite of their advantages to accelerate the rapid conversion of lithium polysulfides (LiPSs). Herein, a series of cobalt-doped vanadium tetrasulfide/reduced graphene oxide (x%Co-VS₄/rGO) composites with an ultrathin layered structure as an active sulfur-host material are prepared by a one-pot hydrothermal method. The well-designed two-dimensional ultrathin 3%Co-VS₄/rGO with heteroatom architecture defects (defect of Co-doping and defect of S-vacancies) can significantly improve the adsorption ability on LiPSs, the electrocatalytic activity in the Li₂S potentiostatic deposition, and the active sulfur reduction/oxidation conversion reactions and greatly boost the electrochemical performances of Li-S batteries. On the one hand, the ultrathin 3%Co-VS₄/rGO possesses good conductivity inheriting from rGO which contributes to the capacity of internal redox reactions on lithiation from VS₄. On the other hand, the hybrid architectures provide strong adsorption and excellent electrocatalytic ability on LiPSs, which benefit from the surface defects caused by heteroatom doping. The S@3%Co-VS₄/rGO cathode displays a high specific capacity of 1332.6 mA h g^-1 at 0.2 C and a low-capacity decay of only 0.05% per cycle over 1000 cycles at 3 C with a primary capacity of 633.1 mA h g^-1. Furthermore, when the sulfur loading (single-side coating) reaches 4.48 mg cm^-2, it still can deliver 756.2 mA h g^-1 after the 100th cycle at 0.2 C with 89.5% capacity retention. In addition, the in situ X-ray diffraction test reveals that the sulfur conversion mechanism is the processes of α-S₈ → Li₂S → β-S₈ (first cycle) and then β-S₈ ↔ Li₂S during the subsequent cycles. The designing strategy with heteroatom doping and self-intercalation capacity adopted in this work would provide novel inspiration for fabricating advanced sulfur-host materials to achieve excellent electrochemical capability in Li-S batteries.

Manipulating the electrocatalytic activity of sulfur cathode via distinct cobalt sulfides as sulfur host materials in lithium-sulfur batteries

For the better development of lithium-sulfur (Li-S) batteries, it is necessary to fabricate sulfur hosts with cheap, rapid sulfur reaction dynamic and inhibiting the shuttling effect of lithium polysulfides (LiPSs). Herein, four hollow cubic materials with two kinds of nitrogen-doped carbon derived from Prussian blue analogues (PBA) precursor, Co₉S₈/MnS/NC@NC-400, CoS₂/MnS/NC@NC-500, CoS_1.097/MnS/NC@NC-600 and CoS_1.097/MnS/NC@NC-700, are reported when the vulcanization temperatures are regulated at 400 °C, 500 °C, 600 °C and 700 °C, respectively. Among them, Co₉S₈/MnS/NC@NC-400, CoS₂/MnS/NC@NC-500 and CoS_1.097/MnS/NC@NC-600 have the similar hollow cubic structure, which can physically confine the LiPSs's shuttle, however, the Co vacancies of CoS_1.097 in the CoS_1.097/MnS/NC@NC-600 can promote the rearrangement of surface electrons, which is beneficial to the diffusion of Li⁺/e^-, improving the electrochemical reaction kinetics. As for the CoS_1.097/MnS/NC@NC-700 with the same substance but almost collapsed structure, the CoS_1.097/MnS/NC@NC-600 can accommodate the volume expansion of sulfur conversion. In the four sulfur-host materials, the CoS_1.097/MnS/NC@NC-600 not only displays the outstanding adsorption ability on LiPSs, but also presents the best electrocatalytic activity in the Li₂S potentiostatic deposition experiments and active sulfur reduction/oxidation conversion reactions, greatly promoting the electrochemical performances of Li-S batteries. The S@CoS_1.097/MnS/NC@NC-600 cathode can deliver 1010.2 mA h g^-1 at 0.5 C and maintain 651.1 mA h g^-1 after 200 cycles. In addition, the in-situ X-ray diffraction (in-situ XRD) test reveals that the sulfur conversion mechanism is the processes of the α-S₈ → Li₂S → β-S₈ (first cycle), then β-S₈ ↔ Li₂S during the subsequent cycles. Based on the fundamental understanding of the design and preparation of Co_xS_y/MnS/NC@NC hosts with the desired adsorption and catalysis functions, the work can provide new insights and reveal the defect-engineering to develop the advanced Li-S batteries.

Enormous-sulfur-content cathode and excellent electrochemical performance of Li-S battery accouched by surface engineering of Ni-doped WS2@rGO nanohybrid as a modified separator

The poor conductivity of sulfur, the lithium polysulfide's shuttle effect, and the lithium dendrite problem still impede the practical application of lithium-sulfur (Li-S) batteries. In this work, the ultrathin nickel-doped tungsten sulfide anchored on reduced graphene oxide (Ni-WS₂@rGO) is developed as a new modified separator in the Li-S battery. The surface engineering of Ni-WS₂@rGO could enhance the cell conductivity and afford abundant chemical anchoring sites for lithium polysulfides (LiPSs) adsorption, which is convinced by the high adsorption energy and the elongate SS bond given using density-functional theory (DFT) calculation. Concurrently, the Ni-WS₂@rGO as a modified separator could effectively catalyze the conversion of LiPSs during the charging/discharging process. The Li-S cell with Ni-WS₂@rGO modified separator achieves a high initial capacity of 1160.8 mA h g^-1 at the current density of 0.2C with a high-sulfur-content cathode up to 80 wt%, and a retained capacity of 450.7 mA h g^-1 over 500 cycles at 1C, showing an efficient preventing polysulfides shuttle to the anode while having no influence on Li⁺ ion transference across the decorating separator. The strategy adopted in this work would afford an effective pathway to construct an advanced functional separator for practical high-energy-density Li-S batteries.