S-scheme mesoporous Li2MnO3/g-C3N4 heterojunctions as efficient photocatalysts for the mineralization of trichloroethylene in aqueous media

Enhanced catalytic performance of CuCr/ZSM-5 catalyst by chemical vapour deposition for trichloroethylene oxidation

The CuCr mixed oxides catalysts supported on ZSM-5 zeolite (CuCr/ZSM-5) were synthesized via metal organic chemical vapour deposition (MOCVD) method for catalytic oxidation of trichloroethylene (TCE). SEM, XRD, BET, H2-TPR, NH3-TPD and XPS were tested. The active components were dispersed uniformly over the surface of ZSM-5 zeolite. The catalytic experimental results exhibited that the CuCr/ZSM-5 exhibited the best catalytic performance for TCE oxidation with 90% of TCE at 338°C and the concentration of C2Cl4 decreased compared with Cu/ZSM-5 and Cr/ZSM-5. The possible reason is that CuCr/ZSM-5 has superior reducibility, higher Cu2+ surface concentration as well as more surface oxygen.

Minimizing CO2 emissions by photocatalytic CO2 reduction to CH3OH over Li2MnO3/WO3 heterostructures under visible illumination

Photocatalytic CO2 reduction to valuable fuels has proved to be a favourable process to produce renewable energy and reduce CO2 emissions, which mostly depends on designing effective photocatalysts with the rapid separation rate of charge carriers. In this contribution, mesoporous n-n heterojunction Li2MnO3/WO3 nanocomposites were designed via a simplistic sol-gel process for CO2 reduction utilizing visible illumination (λ > 420 nm). XRD and TEM measurements confirmed the synthesized Li2MnO3/WO3 nanocomposite is a monoclinic structure, and its particle size is 25 ± 5 nm. The obtained Li2MnO3/WO3 exhibited narrower bandgap energy (1.74 eV), larger surface area (212 m2g-1), exceedingly visible absorbing, and lower recombination of electron and hole. The yield of CH3OH was determined about 198, 871, 1140, 1550 and 1570 mmolg-1 for bare WO3 and 5%, 10%, 15% and 20% Li2MnO3/WO3 nanocomposites, respectively. These results evidenced that the 15% Li2MnO3/WO3 photocatalyst exhibited the best reduction ability compared to other nanocomposites. The CO2 reduction over 15% Li2MnO3/WO3 photocatalyst achieved a maximal CO2 conversion with the substantially boosted CH3OH, i.e., 1550 mmolg-1 after 9 h, which was enhanced 7.8 folds great than of WO3 NPs. Mesoporous Li2MnO3/WO3 nanocomposites, in comparison with bare WO3 NPs, created more active sites for facilitating CO2 and had a specific electric field to more effectively separate charge carriers. The Li2MnO3/WO3 photocatalyst has superior photostability during the continuous reduction of CO2 for 45 h with no remarkable decrease. The possible direct S-scheme mechanism for electron transfer over Li2MnO3/WO3 photocatalyst with the enhanced CO2 reduction ability was discussed. The present work demonstrates an avenue for building highly effective heterostructure photocatalysts in solar-energy-induced potential applications.

In situ fabrication of Z-scheme C3N4/Ti3C2/CdS for efficient photocatalytic hydrogen peroxide production

Photocatalysis is a potential technology to produce hydrogen peroxide with low energy consumption and no pollution. However, when using traditional photocatalysts it is hard to meet the requirements of wide visible light absorption, high carrier separation rate and sufficient active sites. Graphitic carbon nitride (g-C3N4) has great potential in the photocatalytic production of hydrogen peroxide, but its photocatalytic performance is limited by a high carrier recombination ratio. Here, we fabricated the Z-Scheme heterojunction of C3N4/Ti3C2/CdS in situ. The large specific surface area of C3N4 can provide plenty of reactive sites, and the absorption efficiency under visible light is improved with the addition of Ti3C2 and CdS. The better conductivity of Ti3C2 reduces the charge transfer resistance. With the increase of surface charge carriers, the width of the space charge region decreases and the photocurrent density increases significantly. Under visible light irradiation, the H2O2 yield of the ternary photocatalyst reaches 256 μM L-1 h-1, which is about 6 times that of pristine C3N4. After three cycles, the high photocatalytic efficiency can still be maintained. In this paper, the reaction mechanism of photocatalytic hydrogen peroxide production by the C3N4/Ti3C2/CdS composite material is proposed through an in-depth study of energy band theory, which provides a new reference for the design and preparation of high-performance materials for photocatalytic hydrogen peroxide production.

The Adsorption Behaviors and Mechanisms of Humic Substances by Thermally Oxidized Graphitic Carbon Nitride

Thermal oxidation is efficient for enhancing the photocatalysis performance of graphitic carbon nitride (g-C₃N₄), while its effect on adsorption performance has not been fully studied, which is crucial to the application of g-C₃N₄ as adsorbents and photocatalysts. In this study, thermal oxidation was used to prepare sheet-like g-C₃N₄ (TCN), and its application for adsorption of humic acids (HA) and fulvic acids (FA) was evaluated. The results showed that thermal oxidation clearly affected the properties of TCN. After thermal oxidation, the adsorption performance of TCN was enhanced significantly, and the adsorption amount of HA increased from 63.23 (the bulk g-C₃N₄) to 145.35 mg/g [TCN prepared at 600 °C (TCN-600)]. Based on fitting results using the Sips model, the maximum adsorption amounts of TCN-600 for HA and FA were 327.88 and 213.58 mg/g, respectively. The adsorption for HA and FA was markedly affected by pH, alkaline, and alkaline earth metals due to electrostatic interactions. The major adsorption mechanisms included electrostatic interactions, π-π interactions, hydrogen bonding, along with a special pH-dependent conformation (for HA). These findings implied that TCN prepared from environmental-friendly thermal oxidation showed promising prospects for humic substances (HSs) adsorption in natural water and wastewater.

Mesoporous BiVO4/TiO2 heterojunction: enhanced photoabsorption and photocatalytic ability through promoted charge transfer

BiVO₄ has been constructed into heterojunctions with TiO₂ to boost the photocatalytic ability under visible illumination. Here, mesoporous BiVO₄/TiO₂ nanocomposites have been fabricated by a facile sol-gel approach utilizing nonionic surfactant and addressed for morphological, optical, structural, and degradation of ciprofloxacin (CIP) in water under visible illumination as an antibiotic pollutant model. The TEM images demonstrated that the TiO₂ NPs are homogenous in terms of shape and size (15 ± 5 nm). The introduction of BiVO₄ into mesoporous TiO₂ could effectively enhance the rapid separation efficiency of the photoinduced carriers and optical absorption. The 3%BiVO₄/TiO₂ photocatalyst possessed the best degradation efficiency (100%) within 60 min which was promoted 20-folds larger than TiO₂ NPs (5%). 3%BiVO₄/TiO₂ nanocomposite exhibited the fastest degradation rate (2.15 × 10^-2 min^-1), which was 40 times faster than bare TiO₂ photocatalyst (0.05 × 10^-2 min^-1). The enhanced photocatalytic ability originated from superior charge separation characteristics and high solar energy absorption in mesopore structures. The recombination rate and mobility of charge carriers were characterized utilizing photoluminescence (PL) and photoelectrochemical measurements. This work highlights the advantages of mesoporous heterojunction BiVO₄/TiO₂ nanocomposites for photocatalytic performances and provides a multilateral route to design an effective wide-spectrum response photocatalyst for the development of comparable materials. The photocatalytic mechanism for degradation CIP over BiVO₄/TiO₂ was discussed in detail..

Mn3O4@ZnO Hybrid Material: An Excellent Photocatalyst for the Degradation of Synthetic Dyes including Methylene Blue, Methyl Orange and Malachite Green

In this study, we synthesized hybrid systems based on manganese oxide@zinc oxide (Mn₃O₄@ZnO), using sol gel and hydrothermal methods. The hybrid materials exhibited hierarchical morphologies and structures characterized by the hexagonal phase of ZnO and the tetragonal phase of Mn₃O₄. The hybrid materials were tested for degradation of methylene blue (MB), methyl orange (MO), and malachite green (MG) under ultraviolet (UV) light illumination. The aim of this work was to observe the effect of various amounts of Mn₃O₄ in enhancing the photocatalytic properties of ZnO-based hybrid structures towards the degradation of MB, MO and MG. The ZnO photocatalyst showed better performance with an increasing amount of Mn₃O₄, and the degradation efficiency for the hybrid material containing the maximum amount of Mn₃O₄ was found to be 94.59%, 89.99%, and 97.40% for MB, MO and MG, respectively. The improvement in the performance of hybrid materials can be attributed to the high charge separation rate of electron-hole pairs, the co-catalytic role, the large number of catalytic sites, and the synergy for the production of high quantities of oxidizing radicals. The performance obtained from the various Mn₃O₄@ZnO hybrid materials suggest that Mn₃O₄ can be considered an effective co-catalyst for a wide range of photocatalytic materials such as titanium dioxide, tin oxide, and carbon-based materials, in developing practical hybrid photocatalysts for the degradation of dyes and for wastewater treatment.