Engineering the interface of organic/inorganic composite solid-state electrolyte by amino effect for all-solid-state lithium batteries

APTES-mediated Cu2(OH)3(NO3) nanomaterials on the surface of silicone catheters for abscess

Metal-based nanomaterials have remarkable bactericidal effects; however, their toxicity cannot be disregarded. To address this concern, we developed a simple synthesis route for antibacterial catheters using metal-based nanomaterials to reduce toxicity while harnessing their excellent bactericidal properties. The grafting agent (3-aminopropyl)triethoxysilane (APTES) forms -NH2 groups on the catheter surface, onto which copper ions form a nanomaterial complex known as Cu2(OH)3(NO3) (defined as SA-Cu). The synthesized SA-Cu exhibited outstanding contact antibacterial effects, as observed through scanning electron microscopy (SEM), which revealed cell membrane crumbing and bacterial rupture on the catheter surface. Furthermore, SA-Cu exhibited excellent biosafety characteristics, as evidenced by the cell counting kit-8 (CCK-8) assay, which showed no significant cytotoxicity. SA-Cu demonstrated sustained antimicrobial capacity, with in vivo experiments demonstrating over 99% bactericidal efficacy against methicillin-resistant Staphylococcus aureus (MRSA) for two weeks. The transcriptome sequencing results suggested that SA-Cu may exert its bactericidal effects by interfering with histidine and purine metabolism in MRSA. This study presents a straightforward method for synthesizing antimicrobial silicone catheters containing copper nanomaterials using copper ions.

Engineering and regulating the interfacial stability between Li1.3Al0.3Ti1.7(PO4)3-based solid electrolytes and lithium metal anodes for solid-state lithium batteries

InCl3@Li1.3Al0.3Ti1.7(PO4)3-F (InCl3@LATP-F) solid electrolyte powders are designed and fabricated by coating a uniform InCl3 layer on the surface of F--doped Li1.3Al0.3Ti1.7(PO4)3 (LATP-F) solid powders via a feasible wet-chemical technique. The assembled Li/InCl3@LATP-F/Li cell can undergo longer cycles of 2500 h at 0.4 mA cm-2 without obvious increases in the overvoltage compared to 1837 h for the Li/LATP-F/Li cell, and the interfacial resistance demonstrates a sharp decrease from 3428 to 436 Ω for the Li/InCl3@LATP-F/Li cell during the first 500 h. Importantly, the assembled LiCoO2/InCl3@LATP-F/Li cell delivers a high discharge specific capacity of 126.4 mAh g-1 with a 95.42% capacity retention ratio after 100 cycles at 0.5 C, and the value easily returns to 112.9 mAh g-1 when the current density is abruptly set back to 0.1 C after different rate cycles. These improved results can be mainly attributed to the fact that the InCl3 layer with a lithiophilic nature can react with lithium metal to form a Li-In alloy, which can guarantee homogeneous lithium ion flux to avoid the accumulation of ions/electrons across the interface and suppress the growth of lithium dendrites. Moreover, the InCl3 layer can prevent direct contact of the LATP-F solid electrolyte and lithium metal to effectively alleviate the reduction reaction of Ti4+ and preserve the structural stability of the composite electrolyte. Therefore, this work may provide an effective strategy to engineer and regulate the interfacial stability between LATP solid electrolytes and lithium metal anodes for LATP-type solid-state lithium batteries.

Three-dimensional polyimide nanofiber framework reinforced polymer electrolyte for all-solid-state lithium metal battery

The replacement of traditional liquid electrolytes with polyethylene oxide (PEO) based composite polymer electrolytes (CPEs) is an important strategy to address the current flammability and explosiveness of lithium batteries since PEO CPEs have high flexibility, excellent processability and moderate cost. However, the insufficient ionic conductivity and inferior mechanical strength of PEO CPEs do not suit the operating requirements of all-solid-state lithium metal batteries at room temperature. Herein, three-dimensional (3D) framework composed of interweaved high-modulus polyimide (PI) nanofibers along with functional succinonitrile (SN) plasticizers are employed to synergistically reinforce the ionic conductivity and mechanical strength of PEO CPEs. Impressively, benefitting from the synergistic effects of 3D PI framework and SN plasticizer, PI-PEO-SN CPEs exhibits high ionic conductivity of 1.03 × 10^-4 S cm^-1 at 30 °C, remarkable tensile strength of 4.52 MPa, and superior Li dendrites blocking ability (>400 h at 0.1 mA cm^-2). Such favorable features of PI-PEO-SN CPEs endow LiFePO₄/PI-PEO-SN/Li solid-state prototype cells with high specific capacity (151.2 mA h g^-1 at 0.2 C), long cycling lifespan (>150 cycles with 91.7 % capacity retention), and superior operating safety even under bending, folding and cutting harsh conditions. This work will pave the avenues to design and fabricate new high-performance PEO CPEs for the high energy density and safety all-solid-state batteries.

Mixed cellulose ester membrane as an ion redistributor to stabilize zinc anode in aqueous zinc ion batteries

Aqueous zinc-ion batteries (AZBs) with high energy density, low cost and environmental characteristics, have become the promising device for energy storage. However, uncontrolled zinc dendrite growth remains an impediment to the popularization of AZBs. The unrestricted two-dimensional (2D) ions diffusion is the main cause of the above defect. In this work, mixed cellulose ester (MCE) membrane is proposed as the separator. A dense homogeneous pore structure can achieve a physical shunting effect on ion diffusion, which can control and homogenize the ion motion. Further, the mechanism of this physical pore effect is confirmed by comparing the behavior of Zn deposition in MCE systems with different pore sizes but the same composition. As conjectured, a membrane with a smaller pore size is more favorable. In addition, the MCE contains many polar oxygen-containing functional groups that can facilitate and modulate ion diffusion through coordination. This chemical ion guiding effect, together with the above physical pore effect, gives the separator the ability to suppress dendrite formation. Zn/Zn symmetric cells with this membrane exhibit ultralong cycle life exceeding 1250 h at 0.5 mA cm^-2 and 1000 h at 5 mA cm^-2. And the Zn//MnO₂ battery presents excellent cycle stability for more than 500 cycles with a capacity retention of 90.67%. This work proposes MCE separators and reveals their coordinated regulation of physical and chemical effects on metal-based anodes. This will shed light on the development of high-performance separators and AZBs.