Controlled fabrication of nitrogen-doped porous carbon foam with refined hierarchical architectures for desalination via capacitive deionization

Photoselectively modulating main products by changing the wavelength of visible light over D-π-A-D conjugated polymers

The diversity of catalytic products determines the difficulty of selective product modulation, which usually relies on adjusting the catalyst and reaction conditions to obtain different main products selectively. Herein, we synthesized D-π-A-D conjugated organic polymers (TH-COP) using cyclotriphosphonitrile, alkyne, 2H-benzimidazole, and sulfur units as electron donors, π bridges, electron acceptors, and electron donors, respectively. TH-COP exhibited excellent photoinduced carrier separation and redox ability under different visible light wavelengths, and the main products of its CO2 reduction are CH4 (1000.0 μmol g-1) and CO (837.0 μmol g-1) under 400-420 nm and 420-560 nm, respectively. In addition, TH-COP could completely convert phenylmethyl sulfide to methyl phenyl sulfone at 400-420 nm and diphenyl disulfide at 480-485 nm in yields up to 95 %. This study presents a novel strategy for the targeted fabrication of various main products using conjugated polymers by simply changing the wavelength range of visible light.

Carbonized wood fiber-supported S, N-codoped carbon layer-coated multinary metal sulfide nanoarchitecture for efficient oxygen evolution reaction at ampere-level current density

Multinary metal sulfides (MMSs) are highly suitable candidates for the application of electrocatalysis as they offer numerous parameters for optimizing the electronic structure and catalytic sites. Herein, a stable nanoarchitecture consisting of MMSs ((NiCoCrMnFe)Sx) nanoparticles embedded in S, N-codoped carbon (SNC) layers derived from metal organic framework (MOF) and supported on carbonized wood fibers (CWF) was fabricated by directly carbonization. Benefiting from this carbon-coated configuration, along with the synergistic effects within multinary metal systems, (NiCoCrMnFe)Sx@SNC/CWF delivers an exceptionally low overpotential of 260 mV at a high current density of 1000 mA cm-2, a small Tafel slope of 48.5 mV dec-1, and robust electrocatalytic stability. Furthermore, the (NiCoCrMnFe)Sx@SNC/CWF used as the cathode of rechargeable Zn-air batteries demonstrates higher power density and remarkable durability, surpassing that of commercial RuO2. Thus, we showcase the feasibility and advantages of employing highly efficient and durable MMSs materials for low-cost and sustainable energy conversion.

Na2MnSiO4/C as hybrid capacitive deionization electrode material to enhance desalination performance

The utilization of Na2MnSiO4 as a Faraday electrode in hybrid capacitive deionization (HCDI) is investigated to achieve efficient desalination. The Na2MnSiO4/C (NMSO) materials were fabricated via a simple sol-gel method, in which the synthesis process was modulated by adjusting the volume ratio of ethanol to water. When maintaining the volume ratio of water to ethanol at 3:1, the resultant NMSO-3/1 exhibited expected salt adsorption capacity of 31.06 mg g-1 and salt adsorption rate of 20.43 mg g-1 min-1. This distinguished desalination performance was mainly attributed to its inherent multiple redox pairs, as well as the integration of ethanol, which enhanced both specific capacitance and hydrophilicity of the material. This study opens a new perspective for the development of highly efficient materials in HCDI.

Integrated hierarchical porous lignin-based carbon electrode for boosting membrane-free capacitive deionization areal adsorption capacity

The development of high value-added lignin-based functional porous carbon electrodes with excellent properties from sustainable industry lignin powder remains a challenge. This work aims to create robust, binder-free, conductive additives-free, and current collector-free monolithic porous carbon electrodes using industrial lignin powder for membrane-free capacitive deionization (CDI). The material exhibits high mechanical strength, hierarchical porosity structure, large uniform size, and thickness of just a few millimetres (<2.6 mm). In a three-electrode supercapacitor system, the areal specific capacitance of CLCA300-3-1.0 reaches 5.03-1.02 F cm-2 when the scan rate between 1 and 20 mV s-1 in 1 M NaCl solution. As CDI electrodes, the charge efficiency of CLCA300-3-1.0 at different voltages of 1.2 V, 1.4 V and 1.6 V is 0.53, 0.72 and 0.71, respectively. The energy consumption of CLCA280-3-1.0, CLCA300-3-1.0 and CLCA320-3-1.0 tested at 1.2 V are 3.27, 3.40 and 3.25 Wh m-3, respectively. In addition, with thickness increasing to 1.5 mm, the developed CLCA300-3-1.5 electrode exhibits an areal adsorption capacity of 0.46 mg cm-2, and relative highly capacity retention of 84.78 % after 70 cycles. The impressive desalination performance is attributed to the well-designed hierarchical porosity, superhydrophilicity and robust monolithic structure.

Mesoporous dopamine-modified leaf-like zeolitic imidazolate frameworks derived carbon for efficient capacitive deionization

The onstruction of novel porous carbon materials for efficient desalination is crucial but remains challenging for capacitive deionization (CDI) development. Herein, a micelle-assisted strategy was raised to coat mesoporous polydopamine (mPDA) on the surface of two-dimensional (2D) leaf-like zeolitic imidazolate frameworks (ZIFL) followed by confinement pyrolysis. The introduction of the mPDA layer can not only mitigate the backbone collapse of ZIFL during pyrolysis to build a favorable porous environment for efficient ion transport and diffusion, but also induce explosive growth of carbon nanotubes (CNTs) to improve the electron conductivity. As expected, the derivative ZIFL@mPDA-C possessed a high desalination capacity of 41.9 mg g-1 in 500  mg L-1 NaCl solution at an operating voltage of 1.2 V. In particular, the retention ratio of the desalination capacity of ZIFL@mPDA-C was about 100 % after 50 consecutive adsorption-desorption cycles, while its leaf-like morphology and hierarchical pore structures were well preserved. This study highlights the importance of rationally designed structures and components for the performance breakthrough of carbon-based CDI electrode materials.

Layered hydrated-titanium-oxide-laden reduced graphene oxide composite as a high-performance negative electrode for selective extraction of Li via membrane capacitive deionization

In this work, we initially prepared layered lithium titanate (Li2TiO3) using a solid-state reaction. Then Li+ of Li2TiO3 were acid-eluded with Hydrochloric acid to obtain hydrated titanium oxide (H2TiO3). Different weight percentages (50%, 60%, 70%, 80%, and 90%) of the as-prepared H2TiO3 were deposited on a conductive reduced graphene oxide (rGO) matrix to obtain a series of rGO/ H2TiO3 composites. Of the prepared composites, rGO/H2TiO3-60% showed excellent current density, high specific capacitance, and rapid ion diffusion. An asymmetric MCDI (membrane capacitive deionization) cell fabricated with activated carbon as the anode and rGO/H2TiO3-60% as the cathode displayed outstanding Li+ electrosorption capacity (13.67 mg g-1) with a mean removal rate of 0.40 mg g-1 min-1 in a 10 mM LiCl aqueous solution at 1.8 V. More importantly, the rGO/H2TiO3-60% composite electrode exhibited exceptional Li+ selectivity, superior cyclic stability up to 100,000 s, and a Li+ sorption capacity retention of 96.32% after 50 adsorption/desorption cycles. The excellent Li+ extraction obtained by MCDI using the rGO/H2TiO3-60% negative electrode was putatively attributed to: (i) ion exchange between Li+ and H+ of H2TiO3; (ii) the presence of narrow lattice spaces in H2TiO3 suitable for selective Li+ capture; (iii) capture of Li+ by isolated and hydrogen-bonded hydroxyl groups of H2TiO3; and (iv) enhanced interfacial contact and transfer of large numbers of Li+ ions from the electrolyte to H2TiO3 achieved by compositing H2TiO3 with a highly conductive rGO matrix.

Interface engineering induced charge rearrangement boosting reversible oxygen electrocatalysis activity of heterogeneous FeCo-MnO@N-doped carbon nanobox

The advancement of bifunctional oxygen catalysts for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) is imperative yet challenging for the optimization of Zn-air batteries. In this study, we reported the successful incorporation of a novel Mott-Schottky catalytic site within a MnO-FeCo heterojunction into an N-doping carbon nanobox, taking into consideration the effects of the intrinsic electric field and hollow/porous support carriers for electrocatalyst design. As expected, the resulting heterogeneous catalyst exhibited an encouraging half-wave potential of 0.88 V and an impressive limiting-current density of 5.62 mA/cm2 for the ORR, as well as a minimal overpotential of 271 mV at 10 mA/cm2 for the OER, both in alkaline conditions. Furthermore, the Zn-air battery constructed with the heterojunction nanobox product displayed a decent potential gap of 0.621 V, an outstanding power density of 253 mW/cm2, a considerable specific capacity of 761 mAh/gZn, and exceptional stability, with up to 336 h of cycling charging and discharging operation. Consequently, this method of modulating the catalyst's surface charge distribution through an internal electric field at the interface and facilitating mass transport offers a novel avenue for the development of robust bifunctional oxygen catalysts.