Cyclic carbonate synthesis from CO2 and epoxides over diamine-functionalized porous organic frameworks

Synthesis of Ethylene Carbonate by Urea Transesterification Using Zeolitic Imidazolate Framework Derived Fe-Doped ZnO Catalysts

The development of environmentally friendly and efficient methods for the synthesis of ethylene carbonate (EC) is crucial for advancing carbon capture, utilization, and storage technologies. Herein, we present the synthesis of EC through the transesterification of urea with ethylene glycol (EG) using a zeolitic imidazolate framework (ZIF) derived Fe-doped ZnO catalyst (Fe;ZnO-ZIF). The Fe;ZnO-ZIF catalyst, prepared by incorporating Fe dopant atoms into a ZnO-ZIF template, demonstrates excellent catalytic activity, achieving high conversion of reactants and superior selectivity toward EC at 160 °C for 150 min under an applied vacuum (160 mmHg). Based on the thermogravimetric, X-ray spectroscopic, and temperature-programmed desorption analysis, the simultaneous presence of strong Lewis acidic and basic sites in Fe;ZnO-ZIF enables its excellent catalytic performance toward EC synthesis with high selectivity. Acidic sites activate the carbon center in urea, while basic sites facilitate the nucleophilic attack on urea by deprotonation of EG. This synergistic reaction pathway resulting from the interaction between the strong Lewis acidic and basic sites promotes nucleophilic attacks of EG on urea, leading to significantly higher conversion efficiency and selectivity, compared to the commercial benchmark ZnO. Although the establishment of a continuous reaction system which takes into account cyclability and stability of the catalysts is further required in the future, our research reported herein provides valuable insights into the design of synergistic, localized active sites for EC synthesis and contributes to the development of sustainable carbon utilization technologies for achievement of net-zero emissions.

Functionalized β-Cyclodextrins Catalyzed Environment-Friendly Cycloaddition of Carbon Dioxide and Epoxides

Ammonium, imidazole, or pyridinium functionalized β-cyclodextrins (β-CDs) were used as efficient one-component bifunctional catalysts for the coupling reaction of carbon dioxide (CO₂) and epoxide without the addition of solvent and metal. The influence of different catalysts and reaction parameters on the catalytic performance were examined in detail. Under optimal conditions, Im-CD1-I catalysts functionalized with imidazole groups were able to convert various epoxides into target products with high selectivity and good conversion rates. The one-component bifunctional catalysts can also be recovered easily by filtration and reused at least for five times with only slight decrease in catalytic performance. Finally, a possible process for hydroxyl group-assisted ring-opening of epoxide and functionalized group- induced activation of CO₂ was presented.

Synergetic effect of ZnCo2O4/inorganic salt as a sustainable catalyst system for CO2 utilization

Currently, it is essential to consider the rapidly increasing emission of CO₂ into the atmosphere, causing major environmental issues such as climate change and global warming. In this work, we have developed the binary catalyst system (ZnCo₂O₄/inorganic salt) for chemical fixation of CO₂ with epoxides into cyclic carbonates without solvent, and all reactions were performed on a large scale using a 100 ml batch reactor. Two mesoporous catalysts of ZnCo₂O₄ with different architecture, such as flakes (ZnCo-F) and spheres (ZnCo-S) were synthesized and utilized as a heterogeneous catalyst for cycloaddition reaction. The bifunctional property of catalysts is mainly attributed to strong acidic and basic properties confirmed by TPD (NH₃ & CO₂) analysis. The ZnCo-F catalyst exhibited excellent conversion of propylene oxide (99.9%) with good corresponding selectivity of propylene carbonate (≥99%) in the presence of inorganic salt (KI) at 120 °C, 2 MPa, 3 h. In addition, ZnCo-F catalyst demonstrated good catalytic applicability towards the various substrates scope of the epoxide. Furthermore, the catalytic properties were examined by evaluating the reaction parameter such as catalyst loading, pressure, temperature and time. The proposed catalyst exhibited good reusability for cycloaddition reaction without significant change in its catalytic activity and proposed a possible reaction mechanism for chemical fixation of CO₂ with epoxide into cyclic carbonate over ZnCo-F/KI.

Study on Selected Metal-Organic Framework-Based Catalysts for Cycloaddition Reaction of CO2 with Epoxides: A Highly Economic Solution for Carbon Capture and Utilization

The level of carbon dioxide in the atmosphere is growing rapidly due to fossil fuel combustion processes, heavy oil, coal, oil shelter, and exhausts from automobiles for energy generation, which lead to depletion of the ozone layer and consequently result in global warming. The realization of a carbon-neutral environment is the main focus of science and academic researchers of today. Several processes were employed to minimize carbon dioxide in the air, some of which include the utilization of non-fossil sources of energy like solar, nuclear, and biomass-based fuels. Consequently, these sources were reported to have a relatively high cost of production and maintenance. The applications of both homogeneous and heterogeneous processes in carbon capture and storage were investigated in recent years and the focus now is on the conversion of CO2 into useful chemicals and compounds. It was established that CO2 can undergo cycloaddition reaction with epoxides under the influence of special catalysts to give cyclic carbonates, which can be used as value-added chemicals at a different level of pharmaceutical and industrial applications. Among the various catalysts studied for this reaction, metal-organic frameworks are now on the frontline as a potential catalyst due to their special features and easy synthesis. Several metal-organic framework (MOF)-based catalysts were studied for their application in transforming CO2 to organic carbonates using epoxides. Here, we report some recent studies of porous MOF materials and an in-depth discussion of two repeatedly used metal-organic frameworks as a catalyst in the conversion of CO2 to organic carbonates.

Aqueous adsorption of bisphenol A over a porphyrinic porous organic polymer

A new porphyrinic porous organic polymer (PPOP) with high stability and excellent textural properties (929 m²/g surface area with 0.73 cm³/g pore volume) was made via the Friedel-Crafts reaction and applied for bisphenol A (BPA) adsorption in water. The material was examined by X-ray diffraction, N₂ adsorption-desorption isotherms, scanning electron microscopy, infrared spectroscopy, X-ray photoelectron spectroscopy, and solid-state ¹³C CP-MAS nuclear magnetic resonance spectroscopy. PPOP was proven highly effective for capturing BPA among the many adsorbent materials investigated. The Langmuir model could closely match the adsorption isotherm data with a high adsorption amount of ca. 653 mg/g at 25 °C. Approximately 95% of BPA was adsorbed in 50 min, and the pseudo-second-order kinetic model satisfactorily described the adsorption behavior. This adsorption process was exothermic (ΔH° = -39.10 kJ/mol), and the capacity gradually decreased with increasing pH. Spectroscopic analyses indicated that the BPA adsorption on PPOP was affected by (1) π-π interaction between BPA and the aromatic constituents of PPOP, (2) hydrogen bonding between the N sites of porphyrin units in PPOP and the hydroxyl group of BPA and, and (3) hydrophobic interactions. PPOP was easily regenerated after acetone washing, and >98% efficiency was observed throughout the five repeated adsorption-desorption cycles.

Self-Assembly of CDs@NH2-MOF(Ni)/n-Bu4NBr and its Catalytic Performance for CO2 Fixation with Epoxides

Metal–organic frameworks (CDs@NH2-MOF(Ni)) with carbon dots as the core were synthesised successfully by a one-pot method. The synthesised CDs@NH2-MOF(Ni) contain a large number of amine functional groups and a large surface area for capturing CO2. The FT-IR spectra showed that there exists a large number of carboxylate and amine groups on the surface of the carbon dots, and analysis by scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, thermogravimetric, and Brunauer–Emmett–Teller surface area analysis confirmed that the CDs had successfully entered the CDs@NH2-MOF(Ni). The cycloaddition reaction of propylene oxide (PO) and CO2 was carried out using CDs@NH2-MOF(Ni)/tetra-n-butylammonium bromide (TBAB) and NH2-MOF(Ni)/TBAB as catalytic systems, respectively. The reaction results showed that the two catalytic systems have good catalytic performance for the cycloaddition reaction of PO and CO2. Compared with that of the NH2-MOF(Ni)/TBAB system, both the conversion of PO and the yield of propylene carbonate (PC) are improved in the CDs@NH2-MOF(Ni)/TBAB system. Finally, the optimum catalytic reaction conditions, such as time, temperature, CO2 pressure, and five cycles of catalytic effect, were also discussed. Meanwhile, the mechanism of the catalytic system CDs@NH2-MOF(Ni)/TBAB in the cycloaddition reaction of PO and CO2 was proposed in this work.

Silica-Supported Nitrogen-Enriched Porous Benzimidazole-Linked and Triazine-Based Polymers for the Adsorption of CO2

Two crystalline and five amorphous benzimidazole polymers (BINP) were synthesized and conjugated to porous silica via amine and aldehyde-based materials by a simple reflux procedure. The resulting polymers were subject to thermal analysis for monitoring and quantification of the adsorption and desorption of CO₂. All the polymers were capable of adsorbing CO₂ from a flowing stream of only 80 mL/min at 25 °C. The adsorbed CO₂ onto the polymers were effectively desorbed at room temperature, illustrating the potential application of such polymers for repeated adsorption/desorption of CO₂. The CO₂ adsorption capacities of these polymers were dependent upon their nitrogen content, specific surface area, and pore size. The available nitrogen atoms for binding to the carbon of CO₂ via tetrel bonds also plays an important role in the capture of this gas. Minimal and much lower CO₂ adsorption was also noted with two crystalline polymers, compared to the five amorphous counterparts. Intermolecular hydrogen bonding and π-π interaction effectively prevented the polymer N sites of the crystalline polymers from interacting with polarized CO₂ molecules.

The effects of continuous- and stop-flow gas streams on adsorptive removal of benzene vapor using type - II covalent organic polymers

Various materials have been investigated for the adsorptive removal of volatile organic compounds (VOCs, such as benzene). However, most materials proposed for the adsorptive removal of gaseous benzene (and other VOCs) perform relatively poorly (e.g., an impractically low-service 10% breakthrough volume [BTV10] at < 100 ppm). The adsorbent uptake rate (mg g^-1 min^-1) can also be assessed as a function of the gas-stream flow rate (or space velocity). The main aim of this study is to explore the effect of two different gas-stream supply modes - stopped flow (at a fixed stream flow rate of 330 mL atm min^-1) vs. continuous flow (a variable-stream flow rate of 100, 200, or 330 mL atm min^-1) on the adsorption metrics of gaseous benzene on 5 mg of two types of - II covalent organic polymers (COPs: CBAP-1 [DETA], CD; or CBAP-1 [EDA], CE). The sorbent tube outlet stream was sampled by two respective sampling methods (i.e., a large-volume injector [LVI] for stopped flow vs. syringe injection [SI] for continuous flow) for sample quantitation by gas chromatography flame-ionization detection (GC-FID). The observed BTV10 values in the two sampling modes were similar when tested using 10 ppm benzene, irrespective of sorbents: 56/60 (CD) vs. 620/624 L atm g^-1 (CE). BTV10 values increased systematically with decreasing stream-flow rates to reflect the importance of space velocity in adsorptive removal of benzene. The overall assessment of adsorption performance between stopped flow (LVI) and continuous flow (SI) revealed that the performance of the adsorbent is independent of flow mode (e.g., when performance was compared at flow rate of 330 mL min^-1).

Facile fabrication of a heterogeneous Co-modified pyridinecarboxaldehyde-polyethylenimine catalyst for efficient CO2 conversion under mild conditions

A heterogeneous Co-modified pyridinecarboxaldehyde-polyethylenimine catalyst with active metal sites and amine groups exhibited high catalytic activity for CO₂ conversion under mild conditions, even at ambient temperature.

Adsorption properties of advanced functional materials against gaseous formaldehyde

Intense efforts have been made to eliminate toxic volatile organic compounds (VOCs) in indoor environments, especially formaldehyde (FA). In this study, the removal performances of gaseous FA using two metal-organic frameworks, MOF-5 and UiO-66-NH₂, and two covalent-organic polymers, CBAP-1 (EDA) and CBAP-1 (DETA), along with activated carbon as a conventional reference material, were evaluated. To assess the removal capacity of FA under near-ambient conditions, a series of adsorption experiments were conducted at its concentrations/partial pressures of both low (0.1-0.5 ppm/0.01-0.05 Pa) and high ranges (5-25 ppm/0.5-2.5 Pa). Among all tested materials at the high-pressure region ㅐ (e.g., at 2.5 ppm FA), a maximum adsorption capacity of 69.7 mg g^-1 was recorded by UiO-66-NH₂. Moreover, UiO-66-NH₂ also displayed the best 10% breakthrough volume (BTV10) of 534 L g^-1 (0.5 ppm FA) to 2963 L g^-1 (0.1 ppm FA). In contrast, at the high concentration test (at 5, 10, and 25 ppm FA), the maximum BTV10 values were observed as: 137 (UiO-66-NH₂), 144 (CBAP-1 (DETA)), and 36.8 L g^-1 (CBAP-1 (EDA)), respectively. The Langmuir isotherm model was observed to be a better fit of the adsorption data than the Freundlich model under most of the tested conditions. The superiority of UiO-66-NH₂ was attributed to the van der Waals interactions between the linkers (framework) and the hydrocarbon "tail" (FA) coupled with interactions between its open metal sites and the FA carbonyl groups. This study demonstrated the good potential of these advanced functional materials toward the practical removal of gaseous FA in indoor environments.

Recent Advances in the Chemical Fixation of Carbon Dioxide: A Green Route to Carbonylated Heterocycle Synthesis

Carbon dioxide produced by human activities is one of the main contributions responsible for the greenhouse effect, which is modifying the Earth’s climate. Therefore, post-combustion CO2 capture and its conversion into high value-added chemicals are integral parts of today’s green industry. On the other hand, carbon dioxide is a ubiquitous, cheap, abundant, non-toxic, non-flammable and renewable C1 source. Among CO2 usages, this review aims to summarize and discuss the advances in the reaction of CO2, in the synthesis of cyclic carbonates, carbamates, and ureas appeared in the literature since 2017.

Competitive adsorption of gaseous aromatic hydrocarbons in a binary mixture on nanoporous covalent organic polymers at various partial pressures

Covalent-organic polymers (COPs) are recognized for their great potential for treating diverse pollutants via adsorption. In this study, the sorption behavior of benzene and toluene was investigated both individually and in a binary mixture against two types of COPs possessing different -NH₂ functionalities. Namely, the potential of COPs was tested against benzene and toluene in a low inlet partial pressure range (0.5-20 Pa) using carbonyl-incorporated aromatic polymer (CBAP)-1-based diethylenediamine (EDA) [CD] and ethylenetriamine (DETA) [CE]. The maximum adsorption capacity and breakthrough values of both COPs showed dynamic changes with increases in the partial pressures of benzene and toluene. The maximum adsorption capacities (A_max) of benzene (as the sole component in N₂ under atmospheric conditions) on CD and CE were in the range of 24-36 and 33-75 mg g^-1, respectively. In contrast, with benzene and toluene in a binary mixture, the benzene A_max decreased more than two-fold (range of 2.7-15 and 6-39 mg g^-1, respectively) due to competition with toluene for sorption sites. In contrast, the toluene A_max values remained consistent, reflecting its competitive dominance over benzene. The adsorption behavior of the targeted compounds (i.e., benzene and toluene) was explained by fitting the adsorption data by diverse isotherm models (e.g., Langmuir, Freundlich, Elovich, and Dubinin-Radushkevich). The current research would be helpful for acquiring a better understanding of the factors affecting competitive adsorption between different VOCs in relation to a given sorbent and across varying partial pressures.

The design of a novel and resistant Zn(PZDC)(ATZ) MOF catalyst for the chemical fixation of CO2 under solvent-free conditions

Novel Zn(PZDC)(ATZ) with Lewis acid–base sites exhibited strong resistance to acids/alkalis and moisture and possessed high catalytic activity for CO₂ transformation.

Driving dimethyl carbonate synthesis from CO2 and methanol and production of acetylene simultaneously using CaC2

The synthesis of dimethyl carbonate (DMC) from CO2 and methanol is a very interesting reaction, but is thermodynamically limited. In this work, CaC2 was used to consume the water produced in the reaction to shift the reaction equilibrium, and C2H2 was produced at the same time. This is the first work on the combination of driving a thermodynamically unfavorable reaction and producing C2H2 using CaC2.

Cationic Zn-Porphyrin Polymer Coated onto CNTs as a Cooperative Catalyst for the Synthesis of Cyclic Carbonates

The development of solid catalysts containing multiple active sites that work cooperatively is very attractive for biomimetic catalysis. Herein, we report the synthesis of bifunctional catalysts by supporting cationic porphyrin-based polymers on carbon nanotubes (CNTs) using the direct reaction of 5,10,15,20-tetrakis(4-pyridyl)porphyrin zinc(II), di(1H-imidazol-1-yl)methane, and 1,4-bis(bromomethyl)benzene in the presence of CNTs. The bifunctional catalysts could efficiently catalyze the cycloaddition reaction of epoxides and CO₂ under solvent-free conditions with porphyrin zinc(II) as the Lewis acid site and a bromine anion as a nucleophilic agent working in a cooperative way. Furthermore, a relative amount of porphyrin zinc(II) and quaternary ammonium bromide could be facilely adjusted for facilitating cooperative behavior. The bifunctional catalyst with a TOF up to 2602 h^-1 is much more active than the corresponding homogeneous counterpart and is one of the most active heterogeneous catalysts ever reported under cocatalyst-free conditions. The high activity is mainly attributed to the enhanced cooperation effect of the bifunctional catalyst. With a wide substrate scope, the bifunctional catalyst could be stably recycled. This work demonstrates a new approach for the generation of a cooperative activation effect for solid catalysts.

Cycloaddition of CO2 and epoxides over a porous covalent triazine-based polymer incorporated with Fe3O4

A triazine-based organic polymer incorporated with Fe₃O₄ nanoparticles was synthesized and employed as a catalyst for cycloaddition of CO₂ under mild conditions.