Boosting CO2 methanation activity on Ru/TiO2 catalysts by exposing (001) facets of anatase TiO2

Efficient CO2 methanation using nickel nanoparticles supported mesoporous carbon nitride catalysts

The CO₂ methanation technique not only gives a solution for mitigating CO₂ emissions but can also be used to store and convey low-grade energy. The basic character and large surface area of mesoporous carbon nitride, (MCN), are considered promising properties for the methanation of CO₂. So, a series (5-20 wt.%) of Ni-doped mesoporous carbon nitride catalysts were synthesized by using the impregnation method for CO₂ methanation. the prepared catalysts were characterized by several physicochemical techniques including XRD, BET, FT-IR, Raman spectroscopy, TEM, TGA analysis, Atomic Absorption, H₂-TPR, and CO₂-TPD. The catalytic performance was investigated at ambient pressure and temperature range (200-500 °C) using online Gas chromatography system. The prepared catalysts showed good performance where 15%Ni/MCN exhibited the best catalytic conversion and methane yield with 100% methane selectivity at 450 °C for investigated reaction conditions.

Effect of non-ionic surfactant in the solvothermal synthesis of anatase TiO2 nanoplates with a high percentage of exposed {001} facets and its role in the photocatalytic degradation of methylene blue dye

The synthesis of anatase TiO₂ nanoparticles with controlled morphology and increased {001} facets exposed without the presence of fluorine-derived substances is a challenge. Herein, we report a highly effective approach to fabricate anatase TiO₂ nanoplates with exposed {001} facets and their exploitation as robust photocatalytic materials for dye remediation. These materials were synthesized under controlled hydrolysis and condensation reactions, using titanium (IV) n-butoxide in an ethanolic solution, with acetic and sulfuric acids, by a solvothermal method at 190 °C with or without the presence of the non-ionic surfactant Triton® X-100 and then characterized. During TiO₂ crystal synthesis, the effect of a non-ionic surfactant on the TiO₂ particle growth was investigated. Our results demonstrate that the proposed method can synthesize pure and crystalline anatase TiO₂ square nanoplates that form nanostructured spheres with high surface area, uniformly sized mesopores, and exposed {001} facets. The presence of non-ionic surfactant increased the exposed {001} facets percentage of the formed nanoplates from 69 to 80%, decreased the crystallite thickness, but unaffected its crystalline phase and band gap energy. The kinetic constants (K_a e K_b) for the synthesized TiO₂ anatase nanoplates are considerably higher than the commercial TiO₂ anatase constant (K_c). The synthesized photocatalysts show higher efficiency in the photocatalytic removal of methylene blue (MB) than commercial TiO₂ (for t = 120 min).

CO2 Methanation of Biogas over Ni-Mg-Al: The Effects of Ni Content, Reduction Temperature, and Biogas Composition

Biogas is mainly composed of CH4 and CO2, so it is used as an alternative energy to CH4 with high energy density by separating and removing CO2 from biogas. In addition, it can be utilized by producing synthesis gas (CO and H2) through thermal decomposition of biogas or by synthesizing CH4 by methanation of CO2. The technique of CO2 methanation is a method that can improve the CH4 concentration without CO2 separation. This study aims to produce more efficient methane through CO2 methanation of biogas over Ni-Mg-Al catalyst. So, the effect of Ni contents in catalyst, catalyst reduction temperature, CO2 concentration in biogas, and the initial concentration of CH4 on CO2 conversion rate and CH4 selectivity was investigated. In addition, the effect of increasing CO2 concentration, H2/CO2 ratio, and GHSV (gas space velocity per hour) on H2 conversion, CH4 productivity, and product was investigated. In particular, the durability and stability of CO2 methanation was tested over 60 wt% Ni-Mg-Al catalyst at 350 °C and 30,000/h for 130 h. From the long-term test results, the catalyst shows stability by maintaining a constant CO2 conversion rate of 72% and a CH4 selectivity of 95%.

Comparing the Performance of Supported Ru Nanocatalysts Prepared by Chemical Reduction of RuCl3 and Thermal Decomposition of Ru3(CO)12 in the Sunlight-Powered Sabatier Reaction

The preparation of Ru nanoparticles supported on γ-Al2O3 followed by chemical reduction using RuCl3 as a precursor is demonstrated, and their properties are compared to Ru nanoparticles supported on γ-Al2O3 prepared by impregnation of γ-Al2O3 with Ru3(CO)12 and subsequent thermal decomposition. The Ru nanoparticles resulting from chemical reduction of RuCl3 are slightly larger (1.2 vs. 0.8 nm). In addition, Ru nanoparticles were deposited on Stöber SiO2 using both deposition techniques. These particles were larger than the ones deposited on γ-Al2O3 (2.5 and 3.4 nm for chemical reduction and thermal decomposition, respectively). Taking into account the size differences between the Ru nanoparticles, all catalysts display similar activity (0.14–0.63 mol·gRu−1·h−1) and selectivity (≥99%) in the sunlight-powered Sabatier reaction. Ergo, the use of toxic and volatile Ru3(CO)12 can be avoided, since catalysts prepared by chemical reduction of RuCl3 display similar catalytic performance.

Research Progress and Reaction Mechanism of CO2 Methanation over Ni-Based Catalysts at Low Temperature: A Review

The combustion of fossil fuels has led to a large amount of carbon dioxide emissions and increased greenhouse effect. Methanation of carbon dioxide can not only mitigate the greenhouse effect, but also utilize the hydrogen generated by renewable electricity such as wind, solar, tidal energy, and others, which could ameliorate the energy crisis to some extent. Highly efficient catalysts and processes are important to make CO2 methanation practical. Although noble metal catalysts exhibit higher catalytic activity and CH4 selectivity at low temperature, their large-scale industrial applications are limited by the high costs. Ni-based catalysts have attracted extensive attention due to their high activity, low cost, and abundance. At the same time, it is of great importance to study the mechanism of CO2 methanation on Ni-based catalysts in designing high-activity and stability catalysts. Herein, the present review focused on the recent progress of CO2 methanation and the key parameters of catalysts including the essential nature of nickel active sites, supports, promoters, and preparation methods, and elucidated the reaction mechanism on Ni-based catalysts. The design and preparation of catalysts with high activity and stability at low temperature as well as the investigation of the reaction mechanism are important areas that deserve further study.

CO and CO2 Methanation over CeO2-Supported Cobalt Catalysts

CO2 methanation is a promising reaction for utilizing CO2 using hydrogen generated by renewable energy. In this study, CO and CO2 methanation were examined over ceria-supported cobalt catalysts with low cobalt contents. The catalysts were prepared using a wet impregnation and co-precipitation method and pretreated at different temperatures. These preparation variables affected the catalytic performance as well as the physicochemical properties. These properties were characterized using various techniques including N2 physisorption, X-ray diffraction, H2 chemisorption, temperature-programmed reduction with H2, and temperature-programmed desorption after CO2 chemisorption. Among the prepared catalysts, the ceria-supported cobalt catalyst that was prepared using a wet impregnation method calcined in air at 500 °C, and reduced in H2 at 500 °C, showed the best catalytic performance. It is closely related to the large catalytically active surface area, large surface area, and large number of basic sites. The in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) study revealed the presence of carbonate, bicarbonate, formate, and CO on metallic cobalt.

Atomically dispersed Palladium-Ethylene Glycol- Bismuth oxybromide for photocatalytic nitrogen fixation: Insight of molecular bridge mechanism

Performance of single-atom catalysis largely depends on the interaction between the metal and the supporter. Herein, ethylene glycol (EG) was used as a molecular bridge connecting Palladium (Pd) and bismuth oxybromide (BiOBr) to form atomically dispersed Pd catalyst (Pd-EG-BiOBr) for photocatalytic nitrogen fixation under ambient conditions. Compared with 0.20 wt% Pd-BiOBr, 0.20 wt% Pd-EG-BiOBr greatly promoted the photocatalytic nitrogen fixation activity, affording an ammonia formation rate of 124.63 μmol·h^-1. The molecular bridge mechanism during catalyst formation and photocatalysis is speculated based on Transmission electron microscopy, In-situ Fourier transform infrared spectra, Electron spin resonance spectra, UV-vis diffuse reflectance spectra, Photoluminescence spectra and Density Functional Theory calculations. The results show that EG not only induces the formation of atomically dispersed Pd, but also enhances the electron density of Pd and activation capacity of nitrogen molecules. This work opens a new door to applications of atomically dispersed Pd supported catalysts for high efficiency photocatalytic nitrogen fixation.

Ru and Ni—Privileged Metal Combination for Environmental Nanocatalysis

Privileged structures is a term that is used in drug design to indicate a fragment that is popular in the population of drugs or drug candidates that are in the application or investigation phases, respectively. Privileged structures are popular motifs because they generate efficient drugs. Similarly, some elements appear to be more efficient and more popular in catalyst design and development. To indicate this fact, we use here a term privileged metal combination. In particular, Ru-based catalysts have paved a bumpy road in a variety of commercial applications from ammonia synthesis to carbon (di)oxide methanation. Here, we review Ru/Ni combinations in order to specifically find applications in environmental nanocatalysis and more specifically in carbon (di)oxide methanation. Synergy, ensemble and the ligand effect are theoretical foundations that are used to explain the advantages of multicomponent catalysis. The economic effect is another important issue in blending metal combinations. Low temperature and photocatalytic processes can be indicated as new tendencies in carbon (di)oxide methanation. However, due to economics, future industrial developments of this reaction are still questionable.

Recent Progresses in Constructing the Highly Efficient Ni Based Catalysts With Advanced Low-Temperature Activity Toward CO2 Methanation

With the development and prosperity of the global economy, the emission of carbon dioxide (CO2) has become an increasing concern. Its greenhouse effect will cause serious environmental problems, such as the global warming and climate change. Therefore, the worldwide scientists have devoted great efforts to control CO2 emissions through various strategies, such as capture, resource utilization, sequestration, etc. Among these, the catalytic conversion of CO2 to methane is considered as one of the most efficient routes for resource utilization of CO2 owing to the mild reaction conditions and simple reaction device. Pioneer thermodynamic studies have revealed that low reaction temperature is beneficial to the high catalytic activity and CH4 selectivity. However, the low temperature will be adverse to the enhancement of the reaction rate due to kinetic barrier for the activation of CO2. Therefore, the invention of highly efficient catalysts with promising low temperature activities toward CO2 methanation reaction is the key solution. The Ni based catalysts have been widely investigated as the catalysts toward CO2 methanation due to their low cost and excellent catalytic performances. However, the Ni based catalysts usually perform poor low-temperature activities and stabilities. Therefore, the development of highly efficient Ni based catalysts with excellent low-temperature catalytic performances has become the research focus as well as challenge in this field. Therefore, we summarized the recent research progresses of constructing highly efficient Ni based catalysts toward CO2 methanation in this review. Specifically, the strategies on how to enhance the catalytic performances of the Ni based catalysts have been carefully reviewed, which include various influencing factors, such as catalytic supports, catalytic auxiliaries and dopants, the fabrication methods, reaction conditions, etc. Finally, the future development trend of the Ni based catalysts is also prospected, which will be helpful to the design and fabrication of the Ni catalysts with high efficiency toward CO2 methanation process.