Unusual morphology transformation and basicity of magnesium oxide controlled by ageing conditions and its carbon dioxide adsorption

Development of innovative and green adsorbents for in situ cleanup of fluoride-polluted groundwater: Mechanisms and field-scale studies

In this study, the magnesium oxide (MgO)-based adsorbents [granulated MgO aggregates (GA-MgO) and surface-modified MgO powder (SM-MgO)] were developed to remediate a fluoride-contaminated groundwater site. Both GA-MgO and SM-MgO had porous, spherical, and crystalline structures. Diameters for GA-MgO and SM-MgO were 1-1.7 mm and 1-10 μm, respectively. The pseudo second-order dynamic adsorption and the Freundlich isotherm could be applied to express the chemical adsorption phenomena. The monolayer adsorption was the dominant mechanism at the initial adsorption period. During the latter part of fluoride adsorption, the multilayer adsorption became the dominant mechanism for fluoride removal from the water phase, which also resulted in the increased adsorption capacity. Higher hydroxide, phosphate, and carbonate concentrations caused a decreased fluoride removal efficiency due to the competition of sorption sites between fluoride and other anions with similar electronic properties. Fluoride removal mechanism using GA-MgO and SM-MgO as the adsorbents was mainly carried out by the chemical adsorption. Reaction paths contained two main processes: (1) formation of magnesium hydroxide after the reaction of MgO with water, and (2) the hydroxyl group of the magnesium hydroxide was replaced by fluoride ions to form magnesium fluoride precipitation. Results from column tests show that up to 61 and 73% of fluoride removal (initial fluoride concentration = 9.3 mg/L) could be obtained after 50 pore volumes of groundwater pumping with GA-MgO and SM-MgO injection, respectively. The GA-MgO system could be applied to contain and remediate fluoride-contaminated groundwater, and SM-MgO could be applied as an immediate fluoride removal alternative to achieve a rapid pollutant removal for emergency responses. Up to 71% of fluoride removal (fluoride concentration = 10.8 mg/L) could be obtained with GA-MgO injection after 30 days of operation. The developed GA-MgO system is a potential and green remediation alternative to contain the fluoride plume significantly.

CO adsorption on MgO thin-films: formation and interaction of surface charged defects

Two-dimensional (2D) materials formed by thin-films of metal oxides that grow on metal supports are commonly used in heterogeneous catalysis and multilayer electronic devices. Despite extensive research on these systems, the effects of charged defects at supported oxides on surface processes are still not clear. In this work, we perform spin-polarized density-functional theory (DFT) calculations to investigate formation and interaction of charged magnesium and oxygen vacancies, and Al dopants on MgO(001)/Ag(001) surface. The results show a sizable interface compressive effect that decreases the metal work function as electrons are added on the MgO surface with a magnesium vacancy. This surface displays a larger formation energy in a water environment (O-rich condition) even with additional Al-doping. Under these conditions, we found that a polar molecule such as CO is more strongly adsorbed on the low-coordination oxygen sites due to a larger contribution of the channeled electronic transport with the silver interface regardless of the surface charge. Therefore, these findings elucidate how surface intrinsic vacancies can influence or contribute to charge transfer, which allows one to explore more specific reactions at different surface topologies for more efficient catalysts for CO2 conversion.

Polydimethylsiloxane/Magnesium Oxide Nanosheet Mixed Matrix Membrane for CO2 Separation Application

Carbon dioxide (CO₂) concentration is now 50% higher than in the preindustrial period and efforts to reduce CO₂ emission through carbon capture and utilization (CCU) are blooming. Membranes are one of the attractive alternatives for such application. In this study, a rubbery polymer polydimethylsiloxane (PDMS) membrane is incorporated with magnesium oxide (MgO) with a hierarchically two-dimensional (2D) nanosheet shape for CO₂ separation. The average thickness of the synthesized MgO nanosheet in this study is 35.3 ± 1.5 nm. Based on the pure gas separation performance, the optimal loading obtained is at 1 wt.% where there is no observable significant agglomeration. CO₂ permeability was reduced from 2382 Barrer to 1929 Barrer while CO₂/N₂ selectivity increased from only 11.4 to 12.7, and CO₂/CH₄ remained relatively constant when the MMM was operated at 2 bar and 25 °C. Sedimentation of the filler was observed when the loading was further increased to 5 wt.%, forming interfacial defects on the bottom side of the membrane and causing increased CO₂ gas permeability from 1929 Barrer to 2104 Barrer as compared to filler loading at 1 wt.%, whereas the CO₂/N₂ ideal selectivity increased from 12.1 to 15.0. Additionally, this study shows that there was no significant impact of pressure on separation performance. There was a linear decline of CO₂ permeability with increasing upstream pressure while there were no changes to the CO₂/N₂ and CO₂/CH₄ selectivity.

Mg-O-F Nanocomposite Catalysts Defend against Global Warming via the Efficient, Dynamic, and Rapid Capture of CO2 at Different Temperatures under Ambient Pressure

The utilization of Mg-O-F prepared from Mg(OH)2 mixed with different wt % of F in the form of (NH4F·HF), calcined at 400 and 500 °C, for efficient capture of CO2 is studied herein in a dynamic mode. Two different temperatures were applied using a slow rate of 20 mL·min-1 (100%) of CO2 passing through each sample for only 1 h. Using the thermogravimetry (TG)-temperature-programed desorption (TPD) technique, the captured amounts of CO2 at 5 °C were determined to be in the range of (39.6-103.9) and (28.9-82.1) mgCO2 ·g-1 for samples of Mg(OH)2 mixed with 20-50% F and calcined at 400 and 500 °C, respectively, whereas, at 30 °C, the capacity of CO2 captured is slightly decreased to be in the range of (32.2-89.4) and (20.9-55.5) mgCO2 ·g-1, respectively. The thermal decomposition of all prepared mixtures herein was examined by TG analysis. The obtained samples calcined at 400 and 500 °C were characterized by X-ray diffraction and surface area and porosity measurements. The total number of surface basic sites and their distribution over all samples was demonstrated using TG- and differential scanning calorimetry-TPD techniques using pyrrole as a probe molecule. Values of (ΔH) enthalpy changes corresponding to the desorption steps of CO2 were calculated for the most active adsorbent in this study, that is, Mg(OH)2 + 20% F, at 400 and 500 °C. This study's findings will inspire the simple preparation and economical design of nanocomposite CO2 sorbents for climate change mitigation under ambient conditions.

Counter-Intuitive Magneto-Water-Wetting Effect to CO2 Adsorption at Room Temperature Using MgO/Mg(OH)2 Nanocomposites

MgO/Mg(OH)₂-based materials have been intensively explored for CO₂ adsorption due to their high theoretical but low practical CO₂ capture efficiency. Our previous study on the effect of H₂O wetting on CO₂ adsorption in MgO/Mg(OH)₂ nanostructures found that the presence of H₂O molecules significantly increases (decreases) CO₂ adsorption on the MgO (Mg(OH)₂) surface. Furthermore, the magneto-water-wetting technique is used to improve the CO₂ capture efficiency of various nanofluids by increasing the mass transfer efficiency of nanobeads. However, the influence of magneto-wetting to the CO₂ adsorption at nanobead surfaces remains unknown. The effect of magneto-water-wetting on CO₂ adsorption on MgO/Mg(OH)₂ nanocomposites was investigated experimentally in this study. Contrary to popular belief, magneto-water-wetting does not always increase CO₂ adsorption; in fact, if Mg(OH)₂ dominates in the nanocomposite, it can actually decrease CO₂ adsorption. As a result of our structural research, we hypothesized that the creation of a thin H₂O layer between nanograins prevents CO₂ from flowing through, hence slowing down CO₂ adsorption during the carbon-hydration aging process. Finally, the magneto-water-wetting technique can be used to control the carbon-hydration process and uncover both novel insights and discoveries of CO₂ capture from air at room temperature to guide the design and development of ferrofluid devices for biomedical and energy applications.

Morphology Design and Fabrication of Bio-Inspired Nano-MgO-Mg(OH)2 via Vapor Steaming to Enable Bulk CO2 Diffusion and Capture

The absorption of CO₂ on MgO is being studied in depth in order to enhance carbon engineering. Production of carbonate on MgO surfaces, such as MgCO₃, for example, has been shown to hinder further carbon lattice transit and lower CO₂ collecting efficiency. To avoid the carbonate blocking effect, we mimic the water harvesting nano-surface systems of desert beetles, which use alternate hydrophobic and hydrophilic surface domains to collect liquid water and convey condensed droplets down to their mouths, respectively. We made CO₂-philic MgO and CO₂-phobic Mg(OH)₂ nanocomposites from electrospun nano-MgO by vapor steaming for 2-20 min at 100 °C. The crystal structure, morphology, and surface properties of the produced samples were instrumentally characterized using XRD, SEM, XPS, BET, and TGA. We observed that (1) fiber morphology shifted from hierarchical particle and sheet-like structures to flower-like structures, and (2) CO₂ capture capacity shifted by around 25%. As a result, the carbonate production and breakdown processes may be managed and improved using vapor steaming technology. These findings point to a new CO₂ absorption technique and technology that might pave the way for more CO₂ capture, mineralization, and fuel synthesis options.

Synthesis, characterization, CO2 mineralization in air, and thermal decomposition of nano- C8H10MgO10·4H2O powder

Effective solutions for efficient carbon dioxide (CO₂) capture in air at room temperature are in high demand due to the major impacts CO₂ has on global climatic changes. Solid adsorbents materials for CO₂ capture received great attention over the past years, among them, magnesium-based sorbents have been identified as a promising solution for CO₂ capture at intermediate temperatures. This study reports for the first time (1) the synthesis of monoclinic magnesium malate tetrahydrate by combining electrospinning and aging processes, and (2) its room temperature CO₂ adsorption and mineralization in air. Commercial magnesium hydroxide (Mg(OH)₂) powder was used as raw material in the synthesis of magnesium carbonate hydrates (MCH), by three processes; (1) direct calcination, (2) electrospinning and calcination, and (3) electrospinning, calcination, and aging (at room temperature and in air to incubate CO₂ mineralization). The synthesized powder samples were characterized thoroughly using XRD, SEM, EDS, and TGA analyses. Effects of calcination temperature/aging time on CO₂ adsorption (at room temperature), crystallization, and mineralization of MCH were studied. Interestingly, the results showed that the 6-month aged samples (via the third synthesis process above), recorded a CO₂ adsorption capacity of 15.5 wt% within 90 min at 30 °C. Subsequently, three novel mechanisms of thermal decomposition CO₂ adsorption/mineralization were proposed, and a theoretical upper limit of carbon saving potentials was estimated, i.e., 8 mol CO₂ per 1 mol MgO. This work provides a novel CO₂ mineralization approach that results in (1) effective and practical solutions of carbon dioxide (CO₂) emission management and which holds (2) great potential for novel carbon-based fuels development.